Instrukcja obsługi Makita 194043-3
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Makita 194043-3 (28 stron) w kategorii Inny. Ta instrukcja była pomocna dla 9 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/28
Models:
LS0711B, LS0711Z, LS0713/FL
LS0714/F/FL, LS711D, LS1013/F
LS1030N, LS1040/F, LS1212/F
LS1214/F, LS1220, LS1221, 2012NB
GB Stand
Instruction Manual
F Support
Manuel d’instructions
D Ständer
Betriebsanleitung
I Banco
Istruzioni per l’uso
NL Standaard
Gebruiksaanwijzing
EEstante
Manual de instrucciones
P
Base Manual de instruções
DK
Stand Brugsanvisning
S
Maskinbord Bruksanvisning
N
Stativ Bruksanvisning
SF
Teline Käyttöohje
GR Υποστήριγµα Οδηγίεσ χρήσεωσ
TR Sehpai El kitabı
CH 支架 使用說明書
2
12
34
56
78
14
13
2
12
18
45
45
16
19 17
20
16
17
15
10
13
11
12
14
7
8
3
10
9
6
23
4
5
7
1
3
ENGLISH
Explanation of general view
1Frame
2Bolts
3 Support
4 Inner grooves (A)
5 Outer grooves (B)
6Frame pipe
7 Lock plate
8 Support plate (For LS0714 only)
9 The smallest hole in the support
10 Adjusting bolt
11 Front holes in your tool base
12 Front holes in the supports
13 Bolt
14 Nut
15 Fix plates
16 Outer hole (a)
17 Inner hole (b)
18 The largest holes
19 Outer frame
20 Inner frame
Symbols
WARNING:
• Read and thoroughly understand this manual and the
instruction manual of the tool you use before perform-
ing the following.
• Before installing a tool on this stand, always switch off
and unplug the tool.
• The stand should be bolted in a stable and level sur-
face using the bolts provided on three of four feet.
• This stand can be used only with the models of Miter
saws, Compound miter saw, slide compound miter saw
and thicknesser or planer specified in this manual.
• Open and lock before fastening the tool to the stand.
• Fasten the tool to the supports before use.
• Do not climb, sit or stand on this stand.
• Make sure that the stand is set up so that the corporate
nameplate on the stand always faces the operator.
• Do not carry the stand with the tool.
• Before storing or transporting, fold the frame and
secure the supports by tightening bolts on the support
backside.
How to install the stand
When installing miter saw, compound miter saw and
slide compound saw;
1. Loosen the bolts on the backside of the supports.
(Fig. 1)
2. Open the frame and pivot the supports so that the
frame pipe fits in the inner grooves (A) in the sup-
ports. (Fig. 1)
3. Adjust the position of two supports according to the
distance of front holes in the base of the tool you use.
Push down the lock plate to lock it. (Fig. 1)
Note:
Only when using Model LS0714, install the support
plate so that its holes meet the smallest holes in the
supports and secure it firmly with two bolts. (Fig. 2)
4. Turn the stand so that the adjusting bolt at its foot or
the corporate nameplate faces you. Place the tool in
the middle of the support.
All miter saw models specified in this manual should
be placed so that two front holes of the tool base
match the first front holes on the support. (Fig. 3)
Two rear holes of the tool base meet holes accordingly.
Note: When the holes in the tool base do not align
with those in the support, unlock the lock plate by
raising it, readjust it for fine adjustment and push it
down again to lock it. Secure bolts on the backside
of supports firmly after the adjustment. (Fig. 3)
5. Secure the tool base to the support of the stand with
four hex bolts and four nuts provided with the stand.
Make sure that the two front bolts and nuts have been
firmly tightened in the first front holes in the support.
(Fig. 3)
6. When the stand cannot be set up stable, turn the
adjusting bolt at the foot of stand for proper stability.
After adjustment, make sure that the stand and tool
keep stable. (Fig. 4)
7. Secure the feet of stand to the stable and level sur-
face using holes in the fix plates with three hex bolts.
(Fig. 4)
When installing thicknesser or planer
CAUTION:
When using the thicknesser or planer specified in
this manual, set up the stand in the low position
mode.
Failure to do so may result in fall-down and personal
injury.
1. See (1) and (2) stated above in the titled “When
installing miter saw”.
2. Loosen and remove the bolt and nut that secure the
lock plate and outer frame. Change the installation
position of the lock plate from the outer hole (a) to the
inner hole (b) and retighten the bolt firmly. Repeat the
same action on another side. (Fig. 5)
3. Close the frame slightly, raise the support and detach
the frame pipe from the inner grooves (A) in the sup-
port. While holding the frame on, widen the feet of
frame carefully and fully. Fit the frame pipe in the
outer grooves (B) in the support. (Fig. 6)
4. Adjust the position of the supports according to the
distance of front holes in the base of the tool you use.
Push down the lock plate to lock it. (Fig. 7)
5. Turn the stand so that the adjusting bolt at its foot or
the corporate nameplate faces you. Place the tool in
the middle of the support. Thicknesser or planer
model specified in this manual should be placed so
that four holes of the tool base match the largest
holes on the support of the stand. (Fig. 7)
Note: When the holes in the tool base do not align
with those in the support, unlock the lock plate by
raising it, readjust it for fine adjustment and push it
down again to lock it. Secure bolts on the backside
of supports firmly after the adjustment. (Fig. 7)
6. Secure the tool base to the support of the stand with
four hex bolts and four nuts provided with the stand.
Make sure that these four bolts are inserted from the
underside as shown in the figure. (Fig. 8)
7. The subsequent actions are the same as (6) – (7) in
the “When installing miter saw, compound miter saw
and slide compound saw;”.
❏Read instruction manual.
❏Maximum allowable loading.
MAX
100Kg
(220lbs.)
Specyfikacje produktu
| Marka: | Makita |
| Kategoria: | Inny |
| Model: | 194043-3 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Makita 194043-3, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Inny Makita
6 Lipca 2024
6 Lipca 2024
5 Lipca 2024
5 Lipca 2024
5 Lipca 2024
5 Lipca 2024
5 Lipca 2024
5 Lipca 2024
5 Lipca 2024
5 Lipca 2024
Instrukcje Inny
- Inny AEG
- Inny Voltcraft
- Inny Milwaukee
- Inny Stihl
- Inny Bosch
- Inny Parkside
- Inny Festool
- Inny Kärcher
- Inny Panasonic
- Inny Stanley
- Inny Scheppach
- Inny Proxxon
- Inny Grizzly
- Inny DeWalt
- Inny Einhell
- Inny Hyundai
- Inny Husqvarna
- Inny Fuxtec
- Inny RYOBI
- Inny Wolf Garten
- Inny Cuisinart
- Inny Flex
- Inny LogiLink
- Inny GLORIA
- Inny Wagner
- Inny Max Bahr
- Inny Dremel
- Inny AL-KO
- Inny Güde
- Inny ATIKA
- Inny Numatic
- Inny Airpress
- Inny Ferrex
- Inny Digi
- Inny Tronic
- Inny TurboTronic
- Inny Omega
- Inny Fein
- Inny Ferm
- Inny Hitachi
- Inny Kyoritsu
- Inny PowerPlus
- Inny Vonroc
- Inny Powerfix
- Inny HiKOKI
- Inny Workzone
- Inny EasyMaxx
- Inny OKAY
- Inny Sievert
- Inny Skil
- Inny Laserliner
- Inny Greenworks
- Inny Alpina
- Inny Altrex
- Inny Brennenstuhl
- Inny Lotus
- Inny Oregon
- Inny Bort
- Inny Topcraft
- Inny Sparky
- Inny Gamma
- Inny Zodiac
- Inny Renovator
- Inny Turbotech
- Inny Dolmar
- Inny Duro
- Inny Maxicool
- Inny Varo
- Inny Defort
- Inny Max
- Inny Emco
- Inny Eliet
- Inny Bruder Mannesmann
- Inny Probuilder
- Inny Rupes
- Inny Batavia
- Inny Heidenhain
- Inny Xenteq
- Inny Dunlop
- Inny Tecomec
- Inny Holzmann
- Inny Hofmann
- Inny Kraft
- Inny Huvema
- Inny Black Decker
- Inny Stomer
- Inny Blucave
- Inny NDS
- Inny Bostitch
- Inny Bartec
- Inny Kompernass
- Inny Triton
- Inny Ateq
- Inny Ideen Welt
- Inny Sola
- Inny Ergofix
- Inny Flowserve
- Inny Maxxtools
- Inny PLS - Fluke
- Inny Spero
- Inny Datona
- Inny Komatsu
- Inny Rawlink
- Inny DAP
- Inny Dollken-Weimar
- Inny Powerfix Profi
- Inny Mac Allister
- Inny Gude Pro
- Inny MSW
- Inny IntelliFlo
Najnowsze instrukcje dla Inny
12 Stycznia 2025
11 Stycznia 2025
11 Stycznia 2025
11 Stycznia 2025
11 Stycznia 2025
14 Października 2024
14 Października 2024
30 Września 2024
30 Września 2024
29 Września 2024