Instrukcja obsługi LYYT RL50MWW

LYYT Ulga RL50MWW

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla LYYT RL50MWW (4 stron) w kategorii Ulga. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/4
TUBE LIGHT
Installation Guide
Red 155.010UK
White 155.015 UK
Blue 155.0 20UK
Green 155.0 25UK
Yellow 155.0 30UK
Orange 155.0 35UK
Caution: Please read this guide carefully before installation
Damage caused by misuse is not covered by the warranty
Version 1.0
Introduction
Thank you for choosing Lyyt Tube Light as part of your decorative lighting installation.
This product has been design to add light and colour to indoor or outdoor areas for ed
displays, architectural highlights and themed installations. Please use the following guide to
avoid incorrect installation and get the best results from Lyyt Tube Light.
Tube Light Installation Guide
Construction
Tube comprises a continuous chain of miniature light bulbs (sometimes called rice bul light “bs”
because of their shape), encased in an inner PVC extrusion with an outer coating of coloured
PVC which is resistant to wat -ingress, impact and UV degradation. The product is supplied er
as a 45m roll and can be cut to length as required. The power lead is sold separately .
Storage and Handling
Keep unused rolls or part-rolls in a clean and dry environment. Protect cut ends, if necessary,
with end caps and/or tape not store in freezing temperatures or extreme heat as this can . Do
affect the strength and flexibility of the PVC containment when it is being installed.
Available accessories
153.604UK
End cap for Tube Light
153.624UK
1.5m UK power lead with 2-pin connector, shrink tubing and end cap
153.6 27UK
Silicone glue for waterproof installation 22g tube –
153.6 29UK
Set of 2 couplers for extending or splicing lengths of Tube Light
153.6 30UK
Mounting clip (sold in packs of 25)
153. 316 UK
Plastic channel for Tube Light ngth –2m le
Warning
Lyyt Tube Light operates from 230Vac mains voltage and installation and
connection should be carried out b qualified electrical installer. y a
Safety
• Do not connect Tube Light to power whilst still on the roll or during installation and
ensure all connections are sealed before connecting to the power supply.
• Lyyt Tube Light is IP44 water-resistant and can be used outdoors. Do not submerge or
install the Tube Light in water and keep away from constant flow or jets of water.
Tube Light Installation Guide
Installation
Lyyt Tube Light can be attached to building surfaces, frameworks, suspended or laid into
channels as required. Mounting clips are available which can be screwed in place to fix the
Tube Light to various surfaces and shape it to follow architectural details or specific designs.
Tube Light must be completely uncoiled and should be installed without any overlapping
loops Do not completely enclose the Tube Light and allow space for ventilation and cooling. .
Do not cover or apply heavy stresses to the PVC containment.
Tube Light can be cut to length at the indicated cutting points at 1 metre intervals along the
length of its outer PVC covering. Use a sharp knife or shears to ensure a clean cut.
Likewise, cut lengths or entire rolls of Tube Light can be coupled or spliced together using the
optional 2-pin couplers that can be purchased separately ( Available accessories above). see “ ”
Note: The maximum length that can be connected together is 90m, or 2 complete rolls.
To maintain the water-resistant protection of the product and to insulate the mains voltage
carried through the Tube Light all cut ends and joints must be sealed using silicone glue and ,
heat- rink tubing. See instructions on the following page sh
For straight runs, plastic channel is available in 2 metre lengths and can be installed to hold
the tube light firmly in a straight line.
Tube Light can also be fitted around corners with a minimum bend radi us
of Ø. (Any a mpt to force the Tube Light to follow a smaller radius 60mm tte
can result in damage to the integrity of the PVC insulation, rice bulbs or
connections between them) It is advised to connect the power lead and .
end cap (see below) and power up the Tube Light for a short time to
soften it before making such sharp bends. Avoid bending the Tube Light at
any joi ed connections. nt
Connection
The power lead is supplied with a 2-pin connector with rounded pins on one side and spikes
on the other side. The spikes should be pushed into the cut end of the Tube Light where the
ends of the 2 internal wires can be seen. This is to ensure a good electrical connection.

Specyfikacje produktu

Marka: LYYT
Kategoria: Ulga
Model: RL50MWW

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z LYYT RL50MWW, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Ulga LYYT

LYYT

LYYT RL360M Instrukcja

14 Września 2024
LYYT

LYYT RL50MWW Instrukcja

11 Września 2024
LYYT

LYYT 10B-Mirror-L Instrukcja

11 Września 2024
LYYT

LYYT USB-DW Instrukcja

10 Września 2024
LYYT

LYYT FLEX-B Instrukcja

8 Września 2024
LYYT

LYYT RLC-40 Instrukcja

7 Września 2024
LYYT

LYYT COMPACT-B Instrukcja

6 Września 2024

Instrukcje Ulga

Najnowsze instrukcje dla Ulga

Goobay

Goobay 30780 Instrukcja

15 Października 2024
QTX

QTX DM-X12 Instrukcja

15 Października 2024
Livarno

Livarno IAN 94799 Instrukcja

15 Października 2024
Astro

Astro Denia Instrukcja

13 Października 2024
AFX

AFX Grace GRCP07CBBK Instrukcja

12 Października 2024
AFX

AFX Point PNTP0107L30D1BK Instrukcja

12 Października 2024
Neewer

Neewer TL97C Instrukcja

9 Października 2024
Neewer

Neewer SRP18C Instrukcja

9 Października 2024
Ikea

Ikea STRÅLA 005.824.56 Instrukcja

9 Października 2024
Ikea

Ikea STRÅLA 705.829.38 Instrukcja

9 Października 2024