Instrukcja obsługi LumenRadio CRMX Galileo MAX

LumenRadio Ulga CRMX Galileo MAX

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla LumenRadio CRMX Galileo MAX (2 stron) w kategorii Ulga. Ta instrukcja była pomocna dla 10 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

MANUAL LUMENRADIO CRMX Galileo MAX

APPLICATION AREA

The CRMX Galileo MAX is a wireless lighting control product. It is designed to be

used indoors or outdoors when installed in an IP65 or higher rated environmental

enclosure.

CRMX Galileo MAX is used to replace the cable in DMX-512A systems. CRMX

Galileo MAX can be used together with any CRMX compatible device using

either CRMX Classic or CRXM

2 modes. CRMX Galileo MAX can also be congu-

red to operate in W-DMX mode where it can communicate with W-DMX com-

patible devices.

GENERAL

All personnel must familiarize themselves with the instructions in this leaet befo-

re using this product. This product must not be used if damaged. For additional

documentation for CRMX Galileo series or CRMX in general, scan the QR code

on this leaet or visit www.lumenradio.com.

WARRANTY

All warranty claims for this product shall be directed to the local distributor/reseller.

Warranty is deemed void if:

1. The product is modied, repaired or otherwise altered unless it has been

directed by LumenRadio AB, or

2. The serial number on the product (the QR code) has been compromised.

SYSTEM OVERVIEW

A CRMX system replaces the need to use expensive and cumbersome DMX ca-

bles. Place the Galileo MAX unit in close proximity to the lighting controller, or

connected to a local Ethernet network, and let it wirelessly trasmit the DMX and

RDM data to Galileo RX receiver units or other CRMX compatible receivers –

for instance built-in receivers in wireless-ready xtures from any of LumenRadio’s

partners.

DMX data can be locally daisy-chained with a cable between xtures that are

physically close to each other.

The signal can be repeated to extend the range using a Galileo RX unit with the

repeater option.

SAFETY

Only qualied electricians or service personell trained by LumenRadio may

perform installations with this product. Always follow local electrical code and

regulations.

This products shall only be used together with limited power supplies with UL

insulation class II.

Do not use the product if the product is damaged. Only use cables within the

specied conductor sizes. This product may not be connected directly to mains

power.

INSTALLATION

1. Verify that the product has no physical damage.

2. Clip the unit onto a DIN rail. If installed outdoors, this must be performed

in a minimum IP65 rated environmental enclosure.

3. Mount the antenna or, if installed in an an enclosure, mount the antenna

coax cable.

4. Connect the power supply in accordance with the specied voltage.

5. Connect the Ethernet cable to the RJ45 connector.

6. Power on and verify that the unit starts up correctly without any errors.

7. Set the unit up for the correct protocol to use. See further details on this by

scanning the QR code on this guide.

BOX CONTENT

1 pc. CRMX Galileo MAX unit 1 pc. RP-SMA antenna

1 pc. 2-pin terminal plug for power 1 pc. Quick start guide (this leaet)

SPECIFICATIONS

Power supply: 12-24 VDC +/- 10%

Max. power consumption: 8.5W

Self-healing fuse: Yes

Rated wire size: 0.2 - 1.5mm2

24-16 AWG

IP rating: IP X0

Dimensions (W x H x D): 107 x 93 x 58.7 [mm]

Weight: 195g

Antenna connector: RP-SMA

Operating temp. range: -20 to +55°C

Storage temp. range: -30 to +80°C

Humidity: 0–90% non-condensing

Frequency range CMRX/W-DMX: 24024-2480 MHz (ISM band)

Frequency range WiFi: 5170-5330MHz (ISM band)

5490-5590 MHz (ISM band)

Max. RF power CRMX/W-DMX: 100mW (280mW in US)

Max RF power WiFi: 50mW

Supported protocols: Art-Net, Streaming ACN, RDM

Supported RF protocols: CRMX, CRMX

2, W-DMX G3 & G4S

Ethernet: 10/100 Mbps via RJ45 connector

PoE: IEEE 802.3af

USB: Version 2.0 (only for software updates)

LEGAL

CRMX is a trademark of LumenRadio AB, W-DMX is a trademark of Wireless So-

lution Sweden AB. Wireless Solution Sweden AB is a fully-owned subsidiary of

LumenRadio AB. DMX-512A, RDM and Streaming ACN refers to ANSI national

standards developed and maintained by ESTA, Entertainment Services and Tech-

nology Association. Art-Net Trademark Designed and Copyright Artistic Licence

Engineering Ltd.

This product makes use of US patents 7,432,803; 8,457,023; 10,208,680; EU pa-

tents EP 2415317, EP 2803248; China patents CN 102369774, CN 104041189B

and others.

Verison of this quick start guide: Version 1 (2023-12-04)

MANUFACTURER

LumenRadio AB LumenRadio

Johan Willins gata 6 Alfred-Herrhausen-Allee 3-5

416 64 Gothenburg DE-65760 Eschborn

Sweden Germany

www.lumenradio.com

Scan for additional

information

FCC ID: XRSTIMOMWAN301

FCC ID:2ABCB-RPIRM0

IC ID: 8879A-TIMOMWAN301

IC ID: 20953-RPIRM0

E115504

UL62368-1

CSA C22.2 No. 62368-1

CRMX Galileo MAX

by LumenRadio

MANUAL LUMENRADIO CRMX Galileo MAX

Setting Description

YOUR GALILEO MAX UNIT

NETWORK SETTING

For Galileo MAX to be able to receive data and to be accessible on the network,

it is required to set up the network properly.

DHCP On: receive IP settings from network’s DHCP server

Off: manually set settings (see below for details)

IP The unit’s IP address, for instance 10.0.0.23

Netmask Netmask address, for instance 255.255.0.0

Gateway Default gateway’s IP. Set to 0.0.0.0 if not used.

WIFI

The Galileo MAX has built-in WiFi with an internal antenna. This can be enabled

during installation to allow for easy access from a computer, tablet or phone. It is

recommeded to turn WiFi off after installation is nished.

Set the WiFi up as an access point to allow devices to join.

WEB UI

The Galileo MAX has a web UI allowing all settings to be performed more easiliy

than on the small front-panel screen. This can be accessed from any web browser

via Ethernet or WiFi. Navigate to http://a.b.c.d where a.b.c.d is the device’s IP

address. Or if only one device is present on the network you can use http://

galileomax.local instead.

LINKING RECEIVERS

Before you can control any xtures you must set up the wireless network by link-

ing receivers to the transmitter.

1. Make sure the receivers are unlinked and that they are within communica-

tion range.

2. If a receiver is already linked, please see the receiver’s user manual for in-

structions on how to unlink it.

3. In the menu system - navigate to “Outputs” and then select the output you

wish to link to. Then select “Link” to start the linking process.

4. Wait for the link process to nish.

5. You can now repeat these steps for any other outputs on the Galileo MAX.

UNLINKING RECEIVERS

Unlinking can be performed from the transmitter by selecting “Unlink” from the

output’s menu. This will unlink all currently powered receivers that are within

range that are linked to this output.

Linking can also be done from one specic receiver. Please refer to the receiver’s

user manual for how to unlink that receiver.

MODE

Galileo MAX can operate in a number of different modes: CRMX

2, CRMX Classic,

W-DMX G3 or W-DMX G4S. The one that is right for your installation depends

on what your receivers support. It is recommended to use a CRMX mode if it is

supported for optimal performance. Use CRMX Classic unless you need more

universes. Some older receivers may only support receiving W-DMX. In this case

you get maximum compatibility using G3 mode.

OUTPUTS

An output can be seen as a virtual DMX output port. Data is sent to an output

after it has been received from a particular universe on the Ethernet network. In

CRMX Classic, W-DMX G3 and G4S modes each radio contains one output. In

CRMX2 mode each radio contains two outputs.

EXPANDING WITH MORE OUTPUTS

Out-of-the-box the Galileo MAX has one radio, that is it has one or two outputs

(two in CRMX2 mode, one in other modes).

Sometimes it can be required to make an installation with more DMX universes.

In those cases, Galileo MAX can be connected to Galileo TX units to expand on

the number of outputs while still receiving the data via the Ethernet network. Up

to three Galileo TX units can be connected, which results in up to eight outputs

in CRMX2 mode or four outputs in other modes. For more information, visit the

LumenRadio website.

NETWORK PROTOCOLS

Galileo MAX supports receiving data via Art-Net (version 4) and/or Streaming

ACN (ANSI E1.31). It is possible to receive data from different protocols going to

different outputs. This allows for great exibility in your lighting network.

Art-Net uses broadcast or unicast and supports up to 32,768 universes on the

network at the same time. Art-Net always requires proper IP address set-up.

Streaming ACN (also called sACN) uses multicast and can be more efcient on

the network. Multicast also allow for sACN to work in some cases even with in-

valid IP settings.

sACN supports up to 64,000 universes on the same network and also supports

universe synchronization for large-scale installations.

RDM (REMOTE DEVICE MANAGEMENT)

Galileo MAX supports RDM via Art-Net. This means that any third-party RDM

controller that supports RDM over Art-Net can be used to congure and monitor

RDM capable devices in the network – such as signal quality levels in the wireless

system or temperature levels in a luminaire.

The specic RDM functions available to you depend on what is supported by the

controller and by the RDM devices.

Galileo MAX also contains[1] a built-in RDM controller that can be accessed from

the web UI through any web browser – from a computer, a phone or a tablet.

[1] Available during 2024 as a downloadable rmware update.

FIRMWARE UPDATE

The software on your Galileo MAX can be updated. It is recommended to look

for an updated version of the software on the LumenRadio website. We are con-

tinuously releasing new software with improvements, xes and new functionality.

Firmware can be updated via the USB port of your Galileo MAX unit:

1. Take a freshly formatted USB thumb drive. It should be formatted using

FAT32.

2. After unpacking the rmware release zip le, copy the .swu le to the root

of the USB thumb drive. Make sure to keep the lename intact.

3. In the menu system - navigate to “Settings” and then “Software update”.

4. The unit will search for the update le on the USB thumb drive and install it.

5. Wait for the update to nish – it may take several minutes.

6. After installation you can remove the USB thumb drive.

Specyfikacje produktu

Marka:	LumenRadio
Kategoria:	Ulga
Model:	CRMX Galileo MAX

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z LumenRadio CRMX Galileo MAX, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Ulga LumenRadio

LumenRadio CRMX Galileo MAX Instrukcja

21 Grudnia 2024

Instrukcje Ulga

Najnowsze instrukcje dla Ulga

Lucide Raka 78376/41/30 Instrukcja

22 Grudnia 2024

Lucide Kyara 78385/32/30 Instrukcja

22 Grudnia 2024

Lucide Naarden 78377/01/17 Instrukcja

22 Grudnia 2024

Lucide Byrsa 78382/40/97 Instrukcja

22 Grudnia 2024

Lucide Raka 78376/31/30 Instrukcja

22 Grudnia 2024

Lucide Thor 73102/01/15 Instrukcja

22 Grudnia 2024

Lucide Tycho 45274/02/30 Instrukcja

22 Grudnia 2024

Lucide Scott 45265/01/30 Instrukcja

22 Grudnia 2024

Lucide Honore 45252/01/97 Instrukcja

22 Grudnia 2024

Lucide Spectrum 09988/24/12 Instrukcja

22 Grudnia 2024