Instrukcja obsługi Louroe Electronics IF-PX
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Louroe Electronics IF-PX (8 stron) w kategorii Karta sieciowa/adapter. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/8

Page 1 of 8 if-px inst 12/12
IF-PX
POE INTERFACE / POWER EXTRACTOR
INSTALLATION AND OPERATING INSTRUCTIONS
6955 VALJEAN AVE, VAN NUYS, CA 91406
PH: (818)994-6498 / FAX: (818)994-6458
/ www.louroe.com
techsupport@louroe.com
®
LOUROE ELECTRONICS® 6 9 5 5 VA L J E A N AVENUE, VAN NUYS, CA 91406 TEL (818) 994-6498 FAX 994-6458
website: www.louroe.com e-mail: sales@louroe.com
(818)
INTRODUCTION
FIG. 1
Model IF-PX is a single zone POE in-line interface designed to extracts power
from an Ethernet connection to power Louroe microphones, speaker/microphones
and external devices that require a 12Vdc supply such as Encoders and Non PoE
IP cameras. The IF-PX supports both one-way and two-way audio. Most
commercial grade line level unbalanced microphones are compatible with this
unit. Audio output has variable gain control.
Terminal blocks are employed to receive signal wiring from a Louroe Verifact
microphone or an AOP-SP speaker/microphone. Two 3.5mm stereo male to
3.5mm stereo male audio cables are included to connect the unit to an IP camera
or Encoder. Both Mode A and Mode B power options of IEEE802.3af are
supported. Outputs for both PoE (Power+Data) and Non-PoE (Data Only)
cameras and Encoders are included. The IF-PX has built-in thermal, overload and
short-circuit protection that protects the unit from overcurrent and over
temperature. The unit shuts down and turns back ON after the fault is removed.
ILLUSTRATED PARTS
1
2
3
4
5
6
7
8
9
10
Power+Data Output Jack
MIC Out Adjust
DC Out Terminal Block
DC IN Power Jack
Mic/Speaker Audio Terminal Block
Audio Input Jack
Data Out Only Jack
Power+Data Input Jack
Audio Output Jack
Power Indicator
Connects to PoE IP Cameras and/or Encoder
Adjust the audio output gain of the microphone
Receives 12Vdc power from external power supply (not supplied)
Receives wiring from Louroe Verifact Microphone and/or AOP-SP series
Connects to data input of Non-PoE IP Cameras, and Encoders.
Connects to PoE (802.3af) Switch or PoE (802.3af) Midspan
Lights Green indicating power is present to the unit
Connects to audio input of IP cameras,
Encoder, etc.
Provides audio to IP Cameras, Encoder, etc.
Receives audio from IP Camera, Encoder, etc. and connects to audio
output for talkback operation
Provides +12Vdc voltage to power external equipment such as
Non-PoE cameras, encoders, relays, etc.
FIG. 2
POE INTERFACE/POWER EXTRACTOR
POWER + DATA
OUT
IEEE 802.3af
POE
MIC OUT
ADJUST
DC OUT
GN D + 12V
DC IN
+12V
AUDIO
DATA
OUT
P/N:LE-520
MIC/SPEAKER
OUT
IN
AUDIO
AB C SP
POWER + DAT
A
IN
1 2 3 4 5 6 7 8 9
10
REAR PANEL FRONT PANEL

10
10
10
1010
CONNECTING PoE SWITCH TO PoE IP CAMERA OR ENCODER (See Fig. 3 and 4)
1. Connect Ethernet cable from PSE (Power Source Equipment) to the Power+Data Input Jack of the IF-PX.
2. Connect Ethernet cable from camera to Power+Data Output Jack of the IF-PX. Camera should now have power
and data running through it. Power Indicator lights up.
3. Microphone Connection :
a) Connect a 2 cond. shielded cable to the terminal block of Louroe’s Verifact microphone. Connect the other end to
the pluggable header (Mic/Speaker Audio Terminal Block ) of the IF-PX. Connect terminal A of microphone to
terminal A of IF-PX; terminal B of microphone to terminal B of IF-PX; terminal C of microphone to terminal C of IF-
PX. Terminal SP of IF-PX is not used when connecting microphone only (one-way listen).
b) Using the patch cable (stereo plug to stereo plug), connect the Audio Output Jack of the IF-PX to the audio input
of the camera.
c) Adjust the Mic Out Adjust potentiometer (as needed) by rotating it clockwise to increase the microphone output to
the camera, or counterclockwise to decrease. This potentiometer is factory set for a gain of 0dB output.
4. AOP-SP Connection (two-way audio): Before connecting the AOP-SP series, make sure that the Ethernet
cables between the PSE, IF-PX and Camera are all connected.
a) Connect
(one-way listen)
See
interconnection diagram(Fig 3) on page 4.
a 3 cond shielded cable between the AOP-SP and the pluggable header (Mic/Speaker Audio Terminal
Block) of the IF-PX. Connect terminal A of the AOP-SP to terminal A of IF-PX; connect terminal B of AOP-SP to
terminal B of IF-PX; terminal C of AOP-SP to terminal C of IF-PX and terminal SP of AOP-SP to terminal SP of IF-
PX.
b) Using the patch cable (stereo plug to stereo plug), connect the Audio Output Jack of the IF-PX to the audio input
of the camera or encoder. Connect the Audio Input Jack of IF-PX to audio output of the camera or encoder. See
interconnection diagram on page 5.
c) See installation instructions of AOP-SP for setting up and operation of the unit.
5. Use an amplified speaker and a microphone to test the audio. A push Setup camera for video and audio monitoring.
to talk microphone is recommended to minimize the echo when doing two-way audio. See camera user manual for
setting up the camera to the network.
1. Do not connect non-PoE complaint devices to Power+Data Output Jack . Failure to do so may damage the
powered equipment.
Plan ahead where to install before making any connections.The IF-PX is supplied with 6’ audio cables for connections
between the IF-PX and camera. The maximum distance between the IP camera and PSE is 100m or 328’.
2. Do not connect wiring from external microphone or AOP-SP to the Mic/Speaker Audio Terminal Block until
all the ethernet cables (RJ45) are connected and power is present to the camera. Failure to do so in sequence,
the camera may not receive power.
INSTALLATION AND OPERATING INSTRUCTIONS
Page 2 of 8 if-px inst 12/12
LOUROE ELECTRONICS® 6 9 5 5 VA L J E A N AVENUE, VAN NUYS, CA 91406 TEL (818) 994-6498 FAX 994-6458
website: www.louroe.com e-mail: sales@louroe.com
(818)
CAUTION
NOTES
CONNECTIONS AND OPERATIONS
5
5
5
55
The IF-PX can power most IP cameras and Encoders, check that the power requirements of the equipment does
not go beyond the IF-PX power output. See IF-PX power output below.
Power output of IF-PX:
12Vdc, 650mA with AOP-SP connected
12Vdc, 850mA with a Louroe microphone only connected
CONNECTING PoE SWITCH TO NON-PoE IP CAMERA OR ENCODER (See Fig 5)
1. Connect Ethernet cable from PSE (Power Source Equipment) to the Power+Data Input Jack of the IF-PX.
2. Connect Ethernet cable from camera to Data Out Only Jack of the IF-PX.
8
8
8
88
1
1
1
11
1
1
1
11
5
5
5
55
9
9
9
99
2
2
2
22
5
5
5
55
9
9
9
99
8
8
8
88
7
7
7
77
6
6
6
66

Page 3 of 8
LOUROE ELECTRONICS® 6 9 5 5 VA L J E A N AVENUE, VAN NUYS, CA 91406 TEL (818) 994-6498 FAX 994-6458
website: www.louroe.com e-mail: sales@louroe.com
(818)
INSTALLATION AND OPERATING INSTRUCTIONS
if-px inst 12/12
SPECIFICATIONS
Ethernet Connectors
Voltage Input
DC Output
Operating Temperature
RJ45 CAT 5 Input and Output Jacks
12Vdc, 800mA
-20°C to +65°C
Optional Power Supply 12Vdc, 2A, Ext. Power Supply
(Not Supplied)
Connectors
Audio Output/Input
Audio Output Gain
Material
up to +15dB
Black Anodized Al 14 Ga
Line level
RJ-45, DC Jack,
Terminal Block for Microphone/Speaker
3.5mm Stereo Jacks for Audio IN/OUT
Dimensions
Weight 13oz.
6”L x 3 1/2”W x 2 1/8”H
36V - 57V
CONNECTING NON-PoE SWITCH TO NON-PoE CAMERA OR ENCODER (See Fig. 6 - Encoder shown)
1. Connect Ethernet cable from Non-PoE Switch to the Power+Data Input Jack of the IF-PX.
2. Connect Ethernet cable from Encoder or Camera to Data Out Only Jack of the IF-PX.
3. Connect DC Out Terminal Block to the power input jack of the encoder or camera. This Terminal block supplies
12Vdc power to the camera or encoder. It can also provide power to other external equipment such relays, etc. that
require a 12Vdc power. Connect 2 wires to the DC Out Terminal Block . At least 20 AWG wires can be use between
the IF-PX and the encoder or camera. Positive 12Vdc connects to terminal marked “+12Vdc” of IF-PX. Negative 12Vdc
or ground connects to terminal marked “GND”of IF-PX. Connect the other end of the 2 wires to the power jack or
terminal block of the encoder or camera. If the encoder or camera has a 2.1mm power jack, an adapter (2-pin terminal
block to 2.1mm male plug) can be used. Connect the wires to the 2-pin terminal block ( ) of the observe polarity
adapter. Plug the adapter to the 2.1mm power jack of the encoder or camera.
4. Connect an external power supply (not included) to the DC In Jack to power the IF-PX and the encoder or camera.
We recommend using a 12Vdc, 2A power supply.
5. Repeat same procedure when connecting Louroe Verifact microphone or AOP-SP (steps 3 thru 5 from the previous
page - Connections and Operations).
8
8
8
88
7
7
7
77
3
3
3
33
3
3
3
33
4
4
4
44
3. Connect 2 wires to the DC Out Terminal Block . At least 20 AWG wires should be used between the IF-PX and the
encoder or camera. Positive 12Vdc connects to terminal marked “+12Vdc” of IF-PX. Negative 12Vdc or ground
connects to terminal marked “GND” of IF-PX. Connect the other end of the 2 wires to the power jack or terminal block
of the encoder or camera. If the encoder or camera has a 2.1mm power jack, an adapter (2-pin terminal block to
2.1mm male plug) can be used. Connect the wires to the 2-pin terminal block ( ) of the adapter. Plug observe polarity
the adapter to the 2.1mm power jack of the encoder or camera.
4. Repeat same procedure when connecting Louroe Verifact microphone or AOP-SP (steps 3 thru 5 from the previous
page - Connections and Operations).
3
3
3
33
Specyfikacje produktu
Marka: | Louroe Electronics |
Kategoria: | Karta sieciowa/adapter |
Model: | IF-PX |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Louroe Electronics IF-PX, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Karta sieciowa/adapter Louroe Electronics

10 Marca 2025
Instrukcje Karta sieciowa/adapter
- Karta sieciowa/adapter Sony
- Karta sieciowa/adapter Yamaha
- Karta sieciowa/adapter Tenda
- Karta sieciowa/adapter Supermicro
- Karta sieciowa/adapter Pioneer
- Karta sieciowa/adapter TP-Link
- Karta sieciowa/adapter Philips
- Karta sieciowa/adapter Conceptronic
- Karta sieciowa/adapter StarTech.com
- Karta sieciowa/adapter Klipsch
- Karta sieciowa/adapter Canon
- Karta sieciowa/adapter Crestron
- Karta sieciowa/adapter Viewsonic
- Karta sieciowa/adapter Asus
- Karta sieciowa/adapter Nedis
- Karta sieciowa/adapter TRENDnet
- Karta sieciowa/adapter MSI
- Karta sieciowa/adapter Toshiba
- Karta sieciowa/adapter D-Link
- Karta sieciowa/adapter Yealink
- Karta sieciowa/adapter ATen
- Karta sieciowa/adapter Terris
- Karta sieciowa/adapter Speed-Link
- Karta sieciowa/adapter Iiyama
- Karta sieciowa/adapter Thrustmaster
- Karta sieciowa/adapter Evolveo
- Karta sieciowa/adapter Martin Logan
- Karta sieciowa/adapter APC
- Karta sieciowa/adapter Alcatel
- Karta sieciowa/adapter Sigma
- Karta sieciowa/adapter Manhattan
- Karta sieciowa/adapter Strong
- Karta sieciowa/adapter Microchip
- Karta sieciowa/adapter Tripp Lite
- Karta sieciowa/adapter Akasa
- Karta sieciowa/adapter Audac
- Karta sieciowa/adapter Cisco
- Karta sieciowa/adapter Kenwood
- Karta sieciowa/adapter Icy Box
- Karta sieciowa/adapter Moxa
- Karta sieciowa/adapter Gembird
- Karta sieciowa/adapter Paradigm
- Karta sieciowa/adapter Lindy
- Karta sieciowa/adapter ZyXEL
- Karta sieciowa/adapter Trust
- Karta sieciowa/adapter LogiLink
- Karta sieciowa/adapter Linksys
- Karta sieciowa/adapter Digitus
- Karta sieciowa/adapter Dahua Technology
- Karta sieciowa/adapter Oehlbach
- Karta sieciowa/adapter Netgear
- Karta sieciowa/adapter AVM
- Karta sieciowa/adapter Velleman
- Karta sieciowa/adapter Ferguson
- Karta sieciowa/adapter Totolink
- Karta sieciowa/adapter Black Box
- Karta sieciowa/adapter ELAC
- Karta sieciowa/adapter Lancom
- Karta sieciowa/adapter Iogear
- Karta sieciowa/adapter Intellinet
- Karta sieciowa/adapter Devolo
- Karta sieciowa/adapter Sennheiser
- Karta sieciowa/adapter Vivotek
- Karta sieciowa/adapter Suunto
- Karta sieciowa/adapter Heckler Design
- Karta sieciowa/adapter Mercusys
- Karta sieciowa/adapter I-TEC
- Karta sieciowa/adapter Ewent
- Karta sieciowa/adapter Draytek
- Karta sieciowa/adapter CLUB3D
- Karta sieciowa/adapter Edimax
- Karta sieciowa/adapter SEH
- Karta sieciowa/adapter AirLive
- Karta sieciowa/adapter EnGenius
- Karta sieciowa/adapter Planet
- Karta sieciowa/adapter Intermec
- Karta sieciowa/adapter NEC
- Karta sieciowa/adapter Antec
- Karta sieciowa/adapter LevelOne
- Karta sieciowa/adapter Axis
- Karta sieciowa/adapter Vivolink
- Karta sieciowa/adapter Teufel
- Karta sieciowa/adapter Aluratek
- Karta sieciowa/adapter Abus
- Karta sieciowa/adapter Rocstor
- Karta sieciowa/adapter Hama
- Karta sieciowa/adapter Microsoft
- Karta sieciowa/adapter Marmitek
- Karta sieciowa/adapter Ubiquiti Networks
- Karta sieciowa/adapter Goobay
- Karta sieciowa/adapter Sharkoon
- Karta sieciowa/adapter Cudy
- Karta sieciowa/adapter QNAP
- Karta sieciowa/adapter Micro Connect
- Karta sieciowa/adapter SVS
- Karta sieciowa/adapter Netis
- Karta sieciowa/adapter Anker
- Karta sieciowa/adapter Allnet
- Karta sieciowa/adapter InLine
- Karta sieciowa/adapter Media-Tech
- Karta sieciowa/adapter Vivanco
- Karta sieciowa/adapter Elo
- Karta sieciowa/adapter Alecto
- Karta sieciowa/adapter Eaton
- Karta sieciowa/adapter Sonnet
- Karta sieciowa/adapter Twelve South
- Karta sieciowa/adapter Allied Telesis
- Karta sieciowa/adapter Eminent
- Karta sieciowa/adapter Targus
- Karta sieciowa/adapter Sitecom
- Karta sieciowa/adapter Aukey
- Karta sieciowa/adapter Lava
- Karta sieciowa/adapter Kensington
- Karta sieciowa/adapter Techly
- Karta sieciowa/adapter Steren
- Karta sieciowa/adapter Buffalo
- Karta sieciowa/adapter ICIDU
- Karta sieciowa/adapter Valcom
- Karta sieciowa/adapter Simplecom
- Karta sieciowa/adapter Grixx
- Karta sieciowa/adapter Intel
- Karta sieciowa/adapter Mede8er
- Karta sieciowa/adapter Konig
- Karta sieciowa/adapter Sweex
- Karta sieciowa/adapter ESI
- Karta sieciowa/adapter Veho
- Karta sieciowa/adapter Maxxter
- Karta sieciowa/adapter Pinnacle
- Karta sieciowa/adapter Ipevo
- Karta sieciowa/adapter IC Intracom
- Karta sieciowa/adapter Emtec
- Karta sieciowa/adapter Russound
- Karta sieciowa/adapter EverFocus
- Karta sieciowa/adapter EQ3
- Karta sieciowa/adapter Hawking Technologies
- Karta sieciowa/adapter Nexxt
- Karta sieciowa/adapter Vantec
- Karta sieciowa/adapter OSD Audio
- Karta sieciowa/adapter Aeon Labs
- Karta sieciowa/adapter OpenVox
- Karta sieciowa/adapter UTEPO
- Karta sieciowa/adapter SIIG
- Karta sieciowa/adapter Hercules
- Karta sieciowa/adapter Hughes & Kettner
- Karta sieciowa/adapter Extron
- Karta sieciowa/adapter Minute Man
- Karta sieciowa/adapter Motu
- Karta sieciowa/adapter SMC
- Karta sieciowa/adapter Star Micronics
- Karta sieciowa/adapter CradlePoint
- Karta sieciowa/adapter Digium
- Karta sieciowa/adapter Riello
- Karta sieciowa/adapter Iconbit
- Karta sieciowa/adapter 7inova
- Karta sieciowa/adapter Perfect Choice
- Karta sieciowa/adapter NUVO
- Karta sieciowa/adapter Canyon
- Karta sieciowa/adapter Rosewill
- Karta sieciowa/adapter Digicom
- Karta sieciowa/adapter Tycon Systems
- Karta sieciowa/adapter Code Corporation
- Karta sieciowa/adapter Hamlet
- Karta sieciowa/adapter Atto
- Karta sieciowa/adapter Raidsonic
- Karta sieciowa/adapter Approx
- Karta sieciowa/adapter Barox
- Karta sieciowa/adapter Raspberry Pi
- Karta sieciowa/adapter Mach Power
- Karta sieciowa/adapter EXSYS
- Karta sieciowa/adapter Altronix
- Karta sieciowa/adapter J5 Create
- Karta sieciowa/adapter Microsemi
- Karta sieciowa/adapter Atlantis Land
- Karta sieciowa/adapter IDIS
- Karta sieciowa/adapter Luxul
- Karta sieciowa/adapter Vigitron
- Karta sieciowa/adapter SMK-Link
Najnowsze instrukcje dla Karta sieciowa/adapter

14 Marca 2025

14 Marca 2025

12 Marca 2025

14 Stycznia 2025

14 Stycznia 2025

8 Stycznia 2025

29 Grudnia 2024

28 Grudnia 2024

27 Grudnia 2024

27 Grudnia 2024