Instrukcja obsługi LifeSpan SP1000
LifeSpan
wyposażenie fitness
SP1000
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla LifeSpan SP1000 (2 stron) w kategorii wyposażenie fitness. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/2
Stretch Partner Warranty
The LifeSpan Stretch Partner comes with the following warranty:
Parts: 90 days seat and flex bumper
1 year for commercial use
2 years for residential use
Frame: 1 year for commercial use
5 years for residential use
PCE Health and Fitness Warrants that the equipment it manufactures is free from defects in material and workmanship under normal
use and service.
If within the timeframe specified above, any part of the Stretch Partner fails to operate properly, contact your authorized PCE Health and
Fitness Retailer to report the problem or contact PCE Health and Fitness at www.pcefitness.com or (435) 940-1180.
PCE Health and Fitness reserves the right to make changes and improvements to our products without incurring any obligations to similarly
alter any product purchased. In order in insure our product warranty and to ensure the safe and efficient operation of LifeSpan equipment,
only authorized parts can be used. The product warranty is void if any parts, other than those provided by PCE Health and Fitness are used.
Exclusions and Limitations
• This Warranty does not apply to any defects caused by negligence, misuse, or improper assembly or maintenance.
• This warranty does not apply to discoloration of paint or plastics.
• PCE Health and Fitness will not be responsible for incidental or consequential damages.
• This warranty is non-transferable from the original owner.
Registration
You must register your LifeSpan product before a warranty claim can be processed and proof of purchase must be demonstrated at the time a
claim is made. To complete your registration online, go to www.pcefitness.com and fill out the online registration or fill out the
warranty card provided with your Stretch Partner and mail it today.
CONTENTS:
• Base
• Handlebar post
• Seat Frame
• Handlebars & Safety Straps
• Seat Bottom
• Seat Back
• Pedal Axle
• Pedals
• Seat Pivot Axle
• Instruction Bracket with
User Instructions
• Plastic Covers
• Hardware Bag/Tools
a. 8 - 5mm Frame Screws
b. 8 - Bent Washers
c. 1 - 5mm Allen Wrench
d. 1 - 4mm Allen Wrench
e. 2 - 14mm Wrench’s
f. 1 - Phillips Screwdriver
g. 1 - 14mm Lock Nut
h. 1 - Straight Washer
STEP 1:
FRAME ASSEMBLY
a. Insert the handlebar post bracket into
the end of the base frame.
b. Align the holes and using four, 5mm
Allen head screws and 4 Bent Washers,
hand tighten all four screws before
securely tightening them with the Allen
wrench provided.
STEP 2:
PLASTIC COVERS
a. Remove the three Phillips head screws
already in place on the plastic covers.
b. Place the 2 plastic halves in place over
the front joint and tighten down the 3
Phillips head screws.
STEP 3:
HANDLEBAR ASSEMBLY
a. Put the Safety Strap around the
handlebars and push the handlebar
down onto the handlebar post.
b. Locate the Instruction bracket and align
the screw hole in the bracket with the
screw hole in the front of the handlebar
post. Hand tighten a 5mm Allen head
screw with Bent Washer.
c. Hand tighten the remaining 3 screws
with bent washers and then securely
tighten all four screws with the 5 mm
Allen wrench provided.
STEP 4:
SEAT AXLE A
a. Locate the seat fra
seat frame in plac
the frame with the
b. Once the holes are
SURE THAT THE IN
THE BRACKET AS
c. Using the 4mm All
shown in the pictur
STEP 5:
SEAT ASSEMBLY
a. Locate the seat bottom, remove the four screws from the back of the seat
bottom and securely tighten all four screws on the seat frame as shown in
diagram below.
b. Locate the seat back, remove the four screws from the seat back and
securely tighten all four screws onto the seat frame bracket.
Note: Turn the seat bottom so that the front of the seat is flush with the oval seat tube. It
should not overhang past the seat tube.
STEP 6:
PEDAL AXLE/PEDALS
a. Locate the pedal axle and the foot pedal. One of the ends on the axle already has a nut and washer in
Over the opposite end, slide the left side pedal.
b. Push the axle through the pedal axle shaft and push the right pedal over the end.
c. Secure the pedal in place by using a washer and locknut. To tighten the nut you will need to use the 2 -
wrenches provided. Put one wrench on each end of the axle and turn clockwise until tight.
d. After the axle nuts are tightened, push the axle caps into the pedals.
Push base onto bracket. Securely
tighten four 5mm Allen head
screws with bent washers.
Push the axle into the brack
and make sure the indent in
axle is aligned with the hole
the frame bracket.
Turn the seat
bottom so the
front of the seat
is flush with the
seat tube.
Tighten down three
Phillips head screws.
Put the right pedal on the axle
and insert through shaft.
Use a socket wrench on each
end to tighten the axle nuts. Push on pedal cap
Below handlebar
Over handlebar
Specyfikacje produktu
| Marka: | LifeSpan |
| Kategoria: | wyposażenie fitness |
| Model: | SP1000 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z LifeSpan SP1000, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje wyposażenie fitness LifeSpan
26 Sierpnia 2024
26 Sierpnia 2024
26 Sierpnia 2024
Instrukcje wyposażenie fitness
- wyposażenie fitness Taurus
- wyposażenie fitness York Fitness
- wyposażenie fitness Precor
- wyposażenie fitness Tunturi
- wyposażenie fitness SereneLife
- wyposażenie fitness Asaklitt
- wyposażenie fitness Marbo Sport
- wyposażenie fitness Maxxmee
- wyposażenie fitness HMS Premium
Najnowsze instrukcje dla wyposażenie fitness
16 Września 2024
16 Września 2024
16 Września 2024
16 Września 2024
16 Września 2024
16 Września 2024
16 Września 2024
16 Września 2024
16 Września 2024
13 Września 2024