Instrukcja obsługi Liberty Garden 710


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Liberty Garden 710 (9 stron) w kategorii wąż ogrodowy. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/9
VISIT OUR WEBSITE: W . .COM WW LIBERTYGARDENPRODUCTS
OR CALL US TO FREE AT 1-866-820-5805LL
IMPORTANT READ THE OWNER’S MANUAL BEFORE ASSEMBLING :
LIBERTY GARDEN PRODUCTS, INC.
1161 SOUTH PARK DRIVE, RNERSVILLE NC 4KE 2728
Owner’s Ma alnu
WATCH THE VIDEO
Model #710
TOOLS REQUIRED:
PARTS LIST
HARDWARE INCLUDED
BB
AA
A
2
C
B D
CC
PliersAA. Allen wrench (Supplied) Adjustable wrench Drill
BB. Allen bolts (2)
A. B. C. D. Crank handle (1) Leader hose (1) Base shelf (1) Hose reel (1)
DD
DD. Allen screw (1)CC. Lock nuts (2)
Note: Hardware not shown to actual size.
Estimated Assembly Time : 10 minutes (not including mounting the hose reel)
PRE-ASSEMBLY
The wall mounting hardware is included with this unit. Check with the retailer or visit a hardware store to purchase.NOT
IMPORTANT: LAY OUT ALL PARTS AND FASTENERS. MAKE SURE ALL PARTS ARE
ACCOUNTED FOR. IF ANY PART IS MISSING PLEASE CONTACT LIBERTY GARDEN PRODUCTS
AT YOU CAN ALSO VISIT OUR 1-866-820-5805. DO NOT CONTACT THE RETAILER.
WEBSITE, WWW.LIBERTYGARDENPRODUCTS.COM, FOR MORE INSTRUCTIONS, PICTURES
AND HELPFUL HINTS.
3
INSTALLATION
1 2
NOTE: The following hardware (not included)
is recommended for installation.
NOTE: The following hardware (not included)
is recommended for installation.
Position and hold your Navigator base shelf (C) against
the brick masonry wall at a convenient height. Mark the
position of each suspension hole on the wall. Remove the
base shelf (C).
Using a power drill, drill holes 5/16” in diameter and
1 5/8” deep at the marked positions on the wall.
Insert the masonry wall anchors into the anchor sleeve.
Next, insert the anchor and sleeve into the drilled holes
until the steel sleeve is completely in the wall.
Place the base shelf (C) on the masonry wall anchors.
Install a washer, lock washer, and nut over each wall
anchor and tighten securely.
Position and hold your Navigator hose reel base shelf
(C) against the wood wall at a convenient height. Mark
the position of each suspension hole on the wall.
Remove the base shelf (C).
Using a power drill, drill pilot holes 1/4” in diameter and
2 1/2” deep at the marked positions on the wall.
Align the hose reel suspension holes with the pilot
holes.
Attach the base shelf (C) to the wall using the lag
screws with washers and tighten securely.
MOUNTING ON BRICK MASONRY WALL MOUNTING ON FLAT WOOD FRAME WALL
(4) 7 or 8 mm x 60 mm masonry wall anchors
(5/16” x 2 1/2”)
(4) Anchor sleeves
(4) Washers
(4) Lock washers
(4) Nuts
(4) 7 or 8 mm lag screws with washers
(5/16” x 2 1/2”)
This hose reel must be mounted to a solid masonry wall or to wall studs
C
Mounting Hole
Size: 5/16
Mounting Hole
Size: 1/4”
TIP: Remember to use the correct size and quantity of hardware to properly support the
total weight of the unit. A standard 100' length of garden hose weighs approximately 15 lbs.
Filled with water the additional weight can exceed 20 lbs. The mounting hardware must be
able to support the combined weight of the unit, garden hose, plus water.
C
:
NOTE: Drill hole diameters may vary based on anchor sleeve,
concrete screws, and wood screw manufacturer.
Check product recommendations before drilling holes.


Specyfikacje produktu

Marka: Liberty Garden
Kategoria: wąż ogrodowy
Model: 710

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Liberty Garden 710, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą