Instrukcja obsługi Leviton SGVSM-W

Leviton Kontroler SGVSM-W

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Leviton SGVSM-W (2 stron) w kategorii Kontroler. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

Strauss™ Volume Control

200 Watts (100 RMS)

Cat. No. SGVSM

DI-000-SGVSM-00A

INSTALLATION

WARNING: TO BE INSTALLED AND/OR USED IN ACCORDANCE WITH APPROPRIATE ELECTRICAL CODES AND

REGULATIONS.

WARNING: MAXIMUM AMPLIFIER POWER IS 100 WATTS PER CHANNEL. HIGHER AMPLIFIER POWER MAY

CAUSE DAMAGE.

Before starting connections, please note that the left and right attenuator circuits are completely isolated from each other

to prevent instability when used with certain types of ampliﬁers which have ﬂoating grounds. If the ampliﬁer to be used

has common grounds between channels, a 3 wire system can be used between the ampliﬁer and control, but it will be

necessary to connect a jumper between the control ground returns (L- & R-).

If one ground is open, there will be no output on the ungrounded channel at any attenuator setting.

The connectors on the attenuator are the screw-to-tighten type. Connect wires per WIRING DIAGRAM as follows:

1. Select location for mounting control.

NOTE: Due to the depth of volume control, a low-voltage ring or deep electrical box is recommended.

2. Make connections by stripping wire insulation back about 1/4” (.63 cm). Twist any loose strands tightly.

NOTE: It is recommended that at least 16 AWG speaker wire be used for runs up to 30’ (9.1 m). For runs longer than

30’ (9.1 m), use 14-18 AWG wire.

3. Insert the wires from the ampliﬁer into the “TO AMP” openings of the connector, Positive-to-Positive and Negative-to-

Negative, then tighten screws. Check for stray wire strands that might cause a short circuit. Make sure the metal part of

the screw connector engages the bare wire, NOT the insulation!

4. Similarly, connect speaker wires to the “TO SPEAKER” openings and tighten screws.

IMPEDANCE NOTE: There are two impedance settings. 2x is used for up to four rooms connected to a single 8 ohm

rated ampliﬁer output and 6x which is used for 5 to six rooms.

5. ensuring that terminal connector is at top. Install control in its operating location,

NOTE: Leave control 3 or 4 positions above minimum volume before starting the system for the ﬁrst time to avoid

damaging the speakers, while still being loud enough to observe operation.

INSTALLATION MANUAL

DI-000-SGVSM-00A

SPECIFICATIONS

Attenuator Type: Ceramic Resistive Network

Switch: 12 position slider, make-before-break contacts, low torque speciﬁcations for smooth feel

Connector: Screw-tight type, removable connector block

Ampliﬁer Power Rating: 200 Watts (100 RMS)

Impedance Matching: 2 x 8 Ohms

(provided by jumpers) 6 x 47 Ohms

Frequency Response: 20-20kHz +/- 1db, 4-16 Ohm load

Attenuation: 36db

For Technical Assistance Call:

1-800-824-3005 (U.S.A. Only)

www.leviton.com/lin

DI-000-SGVSM-00A

4 CONDUCTOR SPEAKER WIRE

1 x 6

Passive Audio Module

4 CONDUCTOR

SPEAKER WIRE

4 CONDUCTOR SPEAKER WIRE

ZONE 1 ZONE 2 ZONE 3

AMPLIFIER

SPEAKER RIGHTSPEAKER RIGHT SPEAKER LEFTSPEAKER LEFTSPEAKER LEFT SPEAKER RIGHT

WIRING DIAGRAM 1: MULTIPLE VOLUME CONTROLS

Plug/Connector Wiring

R L R L

SPEAKER AMP

2x is used for up to four rooms

connected to a single 8 ohm

rated amplifier output, 6x is

used for 5 to six rooms

LIMITED 2 YEAR WARRANTY AND EXCLUSIONS

Leviton warrants to the original consumer purchaser and not for the beneﬁt of anyone else that this product at the time of its sale by Leviton is free of defects in materials

and workmanship under normal and proper use for two years from the purchase date. Leviton’s only obligation is to correct such defects by repair or replacement, at

its option, if within such two year period the product is returned prepaid, with proof of purchase date, and a description of the problem to Leviton Manufacturing Co.,

Inc., Att: Quality Assurance Department, 59-25 Little Neck Parkway, Little Neck, New York 11362-2591. This warranty excludes and there is disclaimed liability

for labor for removal of this product or reinstallation. This warranty is void if this product is installed improperly or in an improper environment, overloaded, misused,

opened, abused, or altered in any manner, or is not used under normal operating conditions or not in accordance with any labels or instructions. There are no other or

implied warranties of any kind, including merchantability and ﬁtness for a particular purpose, but if any implied warranty is required by the applicable jurisdiction,

the duration of any such implied warranty, including merchantability and ﬁtness for a particular purpose, is limited to two years. Leviton is not liable for incidental,

indirect, special, or consequential damages, including without limitation, damage to, or loss of use of, any equipment, lost sales or proﬁts or delay or failure

to perform this warranty obligation. The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise.