Instrukcja obsługi Lenovo System x3500 M4

Lenovo serwer System x3500 M4

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Lenovo System x3500 M4 (168 stron) w kategorii serwer. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/168

IBM System x3500 M4 Type 7383

Installation and User’s Guide



IBM System x3500 M4 Type 7383

Installation and User’s Guide



Important:

Each caution and danger statement in this documentation is labeled

with a number. This number is used to cross reference an English

language caution or danger statement with translated versions of the

caution or danger statement in the document.Safety Information

For example, if a caution statement is labeled "Statement 1,"

translations for that caution statement are in the Safety Information

document under "Statement 1."

Be sure to read all caution and danger statements in this document

before you perform the procedures. Read any additional safety

information that comes with the server or optional device before you

install the device.

viii IBM System x3500 M4 Type 7383: Installation and User’s Guide

Attention: Use No. 26 AWG or larger UL-listed or CSA certified

telecommunication line cord.

Statement 1:

DANGER

Electrical current from power, telephone, and communication cables is

hazardous.

To avoid a shock hazard:

vDo not connect or disconnect any cables or perform installation,

maintenance, or reconfiguration of this product during an electrical

storm.

vConnect all power cords to a properly wired and grounded electrical

outlet.

vConnect to properly wired outlets any equipment that will be attached to

this product.

vWhen possible, use one hand only to connect or disconnect signal

cables.

vNever turn on any equipment when there is evidence of fire, water, or

structural damage.

vDisconnect the attached power cords, telecommunications systems,

networks, and modems before you open the device covers, unless

instructed otherwise in the installation and configuration procedures.

vConnect and disconnect cables as described in the following table when

installing, moving, or opening covers on this product or attached

devices.

To Connect: To Disconnect:

1. Turn everything OFF.

2. First, attach all cables to devices.

3. Attach signal cables to connectors.

4. Attach power cords to outlet.

5. Turn device ON.

1. Turn everything OFF.

2. First, remove power cords from outlet.

3. Remove signal cables from connectors.

4. Remove all cables from devices.

Safety ix

Statement 2:

CAUTION:

When replacing the lithium battery, use only IBM Part Number 33F8354 or an

equivalent type battery recommended by the manufacturer. If your system has

a module containing a lithium battery, replace it only with the same module

type made by the same manufacturer. The battery contains lithium and can

explode if not properly used, handled, or disposed of.

Do not:

vThrow or immerse into water

vHeat to more than 100°C (212°F)

vRepair or disassemble

Dispose of the battery as required by local ordinances or regulations.

xIBM System x3500 M4 Type 7383: Installation and User’s Guide

Statement 3:

CAUTION:

When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or

transmitters) are installed, note the following:

vDo not remove the covers. Removing the covers of the laser product could

result in exposure to hazardous laser radiation. There are no serviceable

parts inside the device.

vUse of controls or adjustments or performance of procedures other than

those specified herein might result in hazardous radiation exposure.

DANGER

Some laser products contain an embedded Class 3A or Class 3B laser

diode. Note the following.

Laser radiation when open. Do not stare into the beam, do not view directly

with optical instruments, and avoid direct exposure to the beam.

Class 1 Laser Product

Laser Klasse 1

Laser Klass 1

Luokan 1 Laserlaite

Appareil A Laser de Classe 1

Safety xi

Statement 4:

≥ ≥ ≥18 kg (39.7 lb.) 32 kg (70.5 lb.) 55 kg (121.2 lb.)

CAUTION:

Use safe practices when lifting.

Statement 5:

CAUTION:

The power control button on the device and the power switch on the power

supply do not turn off the electrical current supplied to the device. The device

also might have more than one power cord. To remove all electrical current

from the device, ensure that all power cords are disconnected from the power

source.

Statement 6:

CAUTION:

Do not place any objects on top of a rack-mounted device unless that

rack-mounted device is intended for use as a shelf.

Statement 8:

xii IBM System x3500 M4 Type 7383: Installation and User’s Guide

CAUTION:

Never remove the cover on a power supply or any part that has the following

label attached.

Hazardous voltage, current, and energy levels are present inside any

component that has this label attached. There are no serviceable parts inside

these components. If you suspect a problem with one of these parts, contact

a service technician.

Statement 11:

CAUTION:

The following label indicates sharp edges, corners, or joints nearby.

Statement 12:

CAUTION:

The following label indicates a hot surface nearby.

Statement 13:

DANGER

Overloading a branch circuit is potentially a fire hazard and a shock hazard

under certain conditions. To avoid these hazards, ensure that your system

electrical requirements do not exceed branch circuit protection

requirements. Refer to the information that is provided with your device for

electrical specifications.

Safety xiii

Statement 15:

CAUTION:

Make sure that the rack is secured properly to avoid tipping when the server

unit is extended.

Statement 17:

CAUTION:

The following label indicates moving parts nearby.

Statement 26:

CAUTION:

Do not place any object on top of rack-mounted devices.

Statement 27:

CAUTION:

Hazardous moving parts are nearby.

Statement 35:

xiv IBM System x3500 M4 Type 7383: Installation and User’s Guide

CAUTION:

Hazardous energy present. Voltages with hazardous energy might cause

heating when shorted with metal, which might result in splattered metall,

burns, or both.

Attention: This server is suitable for use on an IT power distribution system

whose maximum phase-to-phase voltage is 240 V under any distribution fault

condition.

Safety xv

xvi IBM System x3500 M4 Type 7383: Installation and User’s Guide

Related documentation

This contains general information about the serverInstallation and User’s Guide

including how to set up and cabling the server, how to install supported optional

devices, and how to configure the server. The following documentation also comes

with the server:

vEnvironmental Notices and User Guide

This document is in PDF on the IBM CD. It containsSystem x Documentation

translated environmental notices.

vIBM License Agreement for Machine Code

This document is in PDF. It provides translated versions of the IBM License

Agreement for Machine Code for your product.

vIBM Warranty Information

This printed document contains the warranty terms and a pointer to the IBM

Statement of Limited Warranty on the IBM website.

vLicenses and Attributions Documents

This document is in PDF. It provides the open-source notices.

vProblem Determination and Service Guide

This document is in PDF on the IBM CD. It containsSystem x Documentation

information to help you solve problems yourself, and it contains information for

service technicians.

vSafety Information

This document is in PDF on the IBM CD. It containsSystem x Documentation

translated caution and danger statements. Each caution and danger statement

that appears in the documentation has a number that you can use to locate the

corresponding statement in your language in the document.Safety Information

Depending on the server model, additional documentation might be included on the

IBM CD.System x Documentation

The System x and BladeCenter Tools Center is an online information center that

contains information about tools for updating, managing, and deploying firmware,

device drivers, and operating systems. The System x and BladeCenter Tools Center

is at http://publib.boulder.ibm.com/infocenter/toolsctr/v1r0/index.jsp.

The server might have features that are not described in the documentation that

you received with the server. The documentation might be updated occasionally to

include information about those features, or technical updates might be available to

provide additional information that is not included in the server documentation.

These updates are available from the IBM website. To check for updates, go to

http://www.ibm.com/supportportal/.

Notices and statements in this document

The caution and danger statements in this document are also in the multilingual

Safety Information System x Documentationdocument, which is on the IBM CD.

Each statement is numbered for reference to the corresponding statement in your

language in the document.Safety Information

The following notices and statements are used in this document:

vNote: These notices provide important tips, guidance, or advice.

4IBM System x3500 M4 Type 7383: Installation and User’s Guide

vImportant: These notices provide information or advice that might help you avoid

inconvenient or problem situations.

vAttention: These notices indicate potential damage to programs, devices, or

data. An attention notice is placed just before the instruction or situation in which

damage might occur.

vCaution: These statements indicate situations that can be potentially hazardous

to you. A caution statement is placed just before the description of a potentially

hazardous procedure step or situation.

vDanger: These statements indicate situations that can be potentially lethal or

extremely hazardous to you. A danger statement is placed just before the

description of a potentially lethal or extremely hazardous procedure step or

situation.

Chapter 1. The System x3500 M4 server 5

Table 1. Features and specifications (continued)

Integrated functions:

vIntegrated Management Module II

(IMM2), which consolidates multiple

management functions in a single chip.

vIntel I350AM4 Quad Port Gigabit

Ethernet controller with Wake on LAN

support

vSerial over LAN (SOL) and serial

redirection over Telnet or Secure Shell

(SSH)

vOne systems-management 1 Gb

Ethernet port for connection to a

dedicated systems-management

network. This system management

connector is dedicated to the IMM2

functions.

vLight path diagnostics

vSix Universal Serial Bus (USB) ports

standard

– Two on front of server

– Four on rear of server

vOne internal USB port for optional USB

flash device with embedded hypervisor

vOne internal USB tape connector

vOne serial connector

RAID controllers (depending on the

model):

vA ServeRAID M1115 SAS/SATA adapter

that provides RAID 0, 1, and 10 with

optional FoD RAID 5/50 and SED (Self

Encrypting Drive) upgrade.

vA ServeRAID M5110 SAS/SATA adapter

that provides RAID 0, 1, and 10.

Optional upgrade:

– RAID 5/50 (512 MB Cache) with

optional FoD RAID 6/60 and SED

upgrade

– RAID 5/50 (512 MB Flash) with

optional FoD RAID 6/60 and SED

upgrade

– RAID 5/50 (1 GB Flash) with optional

FoD RAID 6/60 and SED upgrade

– RAID 5/50 and SED (Zero Cache)

Acoustical noise emissions:

vSound power, idling: 6.0 bels

vSound power, operating: 6.0 bels

Environment:

vAir temperature:

– Server on: 10°C to 35°C (50.0°F to

95.0°F); altitude: 0 to 914.4 m

(3000 ft)

– Server on: 10°C to 32°C (50.0°F to

89.6°F); altitude: 914.4 m (3000 ft)

to 2133.6 m (7000 ft)

– Server off (with standby power):

10°C to 43°C (50.0°F to 109.4°F);

maximum altitude: 2133.6 m (7000

ft)

– Shipment: -40°C to 60°C (-40°F to

140°F)

vHumidity:

– Server on: 8% to 80%; maximum

dew point 21°C; maximum rate of

change: 5°C/hour

– Server off (with standby power): 8%

to 80%; maximum dew point: 27°C

vParticulate contamination:

Attention: Airborne particulates and

reactive gases acting alone or in

combination with other environmental

factors such as humidity or

temperature might pose a risk to the

server. For information about the limits

for particulates and gases, see

“Particulate contamination” on page

137.

Heat output:

Approximate heat output:

vMinimum configuration: 2013 Btu per

hour (590 watts)

vMaximum configuration: 3610 Btu per

hour (1058 watts)

Electrical input:

vSine-wave input (50 - 60 Hz) required

vInput voltage low range:

– Minimum: 100 V ac

– Maximum: 127 V ac

vInput voltage high range:

– Minimum: 200 V ac

– Maximum: 240 V ac

vInput kilovolt-amperes (kVA),

approximately:

– Minimum: 0.60 kVA

– Maximum: 1.10 kVA

Notes:

1. Power consumption and heat output

vary depending on the number and type

of optional features installed and the

power-management optional features in

use.

2. The noise emission level stated is the

declared (upper limit) sound power

level, in bels, for a random sample of

machines. All measurements are made

in accordance with ISO 7779 and

reported in conformance with ISO 9296.

Chapter 1. The System x3500 M4 server 7

What your server offers

The server uses the following features and technologies:

vIntegrated Management Module II

The integrated management module II (IMM2) is the second generation of the

IMM. The IMM2 is the common management controller for IBM System x

hardware. The IMM2 consolidates multiple management functions in a single chip

on the server system board.

Some of the features that are unique to the IMM2 are enhanced performance,

expanded compatibility with blade servers, higher-resolution remote video,

expanded security options, and Feature on Demand enablement for hardware

and firmware options.

For additional information, see “Using the Integrated Management Module II” on

page 124.

vUEFI-compliant server firmware

IBM System x Server Firmware (server firmware) offers several features,

including Unified Extensible Firmware Interface (UEFI) 2.1 compliance; Active

Energy Manager technology; enhanced reliability, availability, and serviceability

(RAS) capabilities; and basic input/output system (BIOS) compatibility support.

UEFI replaces the BIOS and defines a standard interface between the operating

system, platform firmware, and external devices. UEFI-compliant System x

servers are capable of booting UEFI-compliant operating systems, BIOS-based

operating systems, and BIOS-based adapters as well as UEFI-compliant

adapters.

Note: The server does not support DOS (Disk Operating System).

vIBM Dynamic System Analysis Preboot diagnostics programs

The Dynamic System Analysis (DSA) Preboot diagnostics programs are stored

on the integrated USB memory. It collects and analyzes system information to aid

in diagnosing server problems. The diagnostic programs collect the following

information about the server:

– System configuration

– Network interfaces and settings

– Installed hardware

– Light path diagnostics status

– Service processor status and configuration

– Vital product data, firmware, and UEFI (formerly BIOS) configuration

– Hard disk drive health

– RAID controller configuration

– Event logs for ServeRAID controllers and service processors

The diagnostic programs create a merged log that includes events from all

collected logs. The information is collected into a file that you can send to IBM

service and support. Additionally, you can view the information locally through a

generated text report file. You can also copy the log to a removable media and

view the log from a web browser.

For additional information about DSA Preboot diagnostics, see the Problem

Determination and Service Guide System x Documentationon the IBM CD

vMulti-core processing

The server supports up to two Intel Xeon™E5-2600 series multi-core

microprocessors. The server comes with only one microprocessor installed.

8IBM System x3500 M4 Type 7383: Installation and User’s Guide

Light path diagnostics provides LEDs to help you diagnose problems. For more

information about the light path diagnostics, see “Light path diagnostics panel” on

page 15 and the on the IBMProblem Determination and Service Guide System x

Documentation CD.

vPCI adapter capabilities

The server has six PCI interface slots. Slot 1 can support PCI Express or PCI-X

adapters through an optional PCI-X interposer card. See “Installing an adapter”

on page 85 for detailed information.

vActive Energy Manager

The IBM Active Energy Manager solution is an IBM Systems Director plug-in that

measures and reports server power consumption as it occurs. This enables you

to monitor power consumption in correlation to specific software application

programs and hardware configurations. You can obtain the measurement values

through the systems-management interface and view them, using IBM Systems

Director. For more information, including the required levels of IBM Systems

Director and Active Energy Manager, see the IBM Systems Director

documentation on the IBM , or see http://www.ibm.com/Systems Director CD

servers/systems/management/director/resources/.

vRedundant connection

The addition of the optional Ethernet daughter card provides failover capability to

a redundant Ethernet connection with the applicable application installed. If a

problem occurs with the primary Ethernet connection and the optional Ethernet

daughter card is installed on the server, all Ethernet traffic that is associated with

the primary connection is automatically switched to the optional redundant

Ethernet daughter card connection. If the applicable device drivers are installed,

this switching occurs without data loss and without user intervention.

vRedundant cooling and optional power capabilities

The server supports a maximum of two 750-watt or 900-watt hot-swap power

supplies and six simple-swap fans, which provide redundancy and hot-swap

capability for a typical configuration. The redundant cooling by the fans in the

server enables continued operation if one of the fans fails. The server comes

with one 750-watt or 900-watt hot-swap power supply and two fans.

You must install fan 2 when you install the second microprocessor in the server.

You can order the optional fan 4, 5, and 6 for cooling redundancy. You can order

the second optional power supply for power redundancy.

Notes:

1. You cannot mix 750-watt and 900-watt power supplies in the server.

2. The server is not running in power redundant mode with two 225W GPUs

installed, two 900-watt power supplies are required.

vServeRAID support

The ServeRAID adapter provides hardware redundant array of independent disks

(RAID) support to create configurations. The standard RAID adapter provides

RAID levels 0, 1, and 10. An optional RAID adapter is available for purchase.

vSystems-management capabilities

The server comes with an integrated management module II (IMM2). When the

IMM2 is used with the systems-management software that comes with the server,

you can manage the functions of the server locally and remotely. The IMM2 also

provides system monitoring, event recording, and network alert capability. The

system-management connector on the rear of the server is dedicated to the

IMM2. The dedicated system-management connector provides additional security

by physically separating the management network traffic from the production

10 IBM System x3500 M4 Type 7383: Installation and User’s Guide

network. You can use the Setup utility to configure the server to use a dedicated

systems-management network or a shared network.

Reliability, availability, and serviceability

Three important computer design features are reliability, availability, and

serviceability (RAS). The RAS features help to ensure the integrity of the data that

is stored in the server, the availability of the server when you need it, and the ease

with which you can diagnose and correct problems.

Your server has the following RAS features:

v3-year parts and 3-year labor limited warranty for machine type 7383

vAutomatic error retry and recovery

vAutomatic restart on nonmaskable interrupt (NMI)

vAutomatic restart after a power failure

vBackup basic input/output system switching under the control of the Integrated

Management Module II (IMM2)

vBuilt-in monitoring for fan, power, temperature, voltage, and power-supply

redundancy

vChipkill memory protection

vDiagnostic support for ServeRAID and Ethernet adapters

vError correcting code (ECC) L2 cache and system memory

vSimple-swap cooling fans with speed-sensing capability

vHot-swap hard disk drives

vInformation and light path diagnostics LED panels

vIntegrated Management Module II (IMM2)

vMenu-driven setup, system configuration, and redundant array of independent

disks (RAID) configuration programs

vMicroprocessor built-in self-test (BIST), internal error signal monitoring,

configuration checking, and microprocessor and voltage regulator module failure

identification through light path diagnostics

vMemory mirrored channel support (memory mirrored channel are mutually

exclusive of each other)

vParity checking on the small computer system interface (SCSI) bus and PCI

buses

vPower management: Compliance with Advanced Configuration and Power

Interface (ACPI)

vPower-on self-test (POST)

vPredictive Failure Analysis (PFA) alerts on memory, SAS/SATA hard disk drives,

fans, and power supplies

vRedundant Ethernet capabilities with failover support

vRedundant hot-swap power supplies and redundant simple-swap fans

vRedundant Network Interface Card (NIC) support

vRemind button to temporarily turn on the system-error LED

vRemote system problem-determination support

vROM-based diagnostics

vROM checksums

vSerial Presence Detection (SPD) on memory, VPD, power supply, and hard disk

drives backplane

vDIMM isolation of excessive correctable error or multi-bit error by the Unified

Extensible Firmware Interface (UEFI)

vStandby voltage for system-management features and monitoring

vStartup (boot) from LAN through remote initial program load (RIPL) or dynamic

host configuration protocol/boot protocol (DHCP/BOOTP)

vSystem auto-configuring from the configuration menu

vSystem-error logging (POST and IMM2)

Chapter 1. The System x3500 M4 server 11

vSystems-management monitoring through the Inter-Integrated Circuit (IC)

protocol bus

vUpgradeable POST, Unified Extensible Firmware Interface (UEFI), diagnostics,

IMM2 firmware, and read-only memory (ROM) resident code, locally or over the

LAN

vVital product data (VPD) on microprocessors, system board, power supplies, and

SAS/SATA (hot-swap hard disk drive) backplane

vWake on LAN capability

IBM Systems Director

IBM Systems Director is a platform-management foundation that streamlines the

way you manage physical and virtual systems supports multiple operating systems

and virtualization technologies in IBM and non-IBM x86 platforms.

Through a single user interface, IBM Systems Director provides consistent views for

viewing managed systems, determining how these systems relate to one other, and

identifying their statuses, helping to correlate technical resources with business

needs. A set of common tasks that are included with IBM Systems Director provides

many of the core capabilities that are required for basic management, which means

instant out-of-the-box business value. The common tasks include the following:

vDiscovery

vInventory

vConfiguration

vSystem health

vMonitoring

vUpdates

vEvent notification

vAutomation for managed systems

The IBM Systems Director web and command-line interfaces provide a consistent

interface that is focused on driving these common tasks and capabilities:

vDiscovering, navigating, and visualizing systems on the network with the detailed

inventory and relationships to the other network resources

vNotifying users of problems that occur on systems and the ability to isolate the

sources of the problems

vNotifying users when systems need updates and distributing and installing

updates on a schedule

vAnalyzing real-time data for systems and setting critical thresholds that notify the

administrator of emerging problems

vConfiguring settings of a single system and creating a configuration plan that can

apply those settings to multiple systems

vUpdating installed plug-ins to add new features and functions to the base

capabilities

vManaging the life cycles of virtual resources

For more information about IBM Systems Director, see the documentation on the

IBM Systems Director CD that comes with the server and the IBM xSeries Systems

Management web page at http://www.ibm.com/systems/software/director/, which

presents an overview of IBM Systems Management and IBM Systems Director.

12 IBM System x3500 M4 Type 7383: Installation and User’s Guide

The Update System PacksXpress

The Update System Pack Installer detects supported and installed deviceXpress

drivers and firmware in the server and installs available updates. For additional

information and to download the Update System Pack Installer, go to theXpress

ToolsCenter for System x and BladeCenter at, go to http://www.ibm.com/systems/

support/supportsite.wss/docdisplay?lndocid=SERV-XPRESS&brandind=5000008.

Server controls, LEDs, and power

This section describes the controls and light-emitting diodes (LEDs) and how to turn

the server on and off. For the locations of other LEDs on the system board, see

“System-board LEDs and controls” on page 34.

Front view

The following illustration shows the controls and LEDs on the front of the server.

Note: The front bezel is not shown so that the drive bays are visible.

Power control

button

DVD drive

eject button

USB 1

USB 2

Reset button

Remind button

Bay 1

Bay 2

DVD drive

activity LED

Hard disk drive

status LED (amber)

Hard disk drive

activity LED (green)

vPower-control button: Press this button to turn the server on and off manually.

vHard disk drive activity LEDs: This LED is used on hot-swap SAS or SATA

hard disk drives. Each hot-swap hard disk drive has an activity LED, and when

this LED is flashing, it indicates that the drive is in use.

vHard disk drive status LEDs: This LED is used on hot-swap SAS or SATA hard

disk drives. When this LED is lit, it indicates that the drive has failed. If an

optional IBM ServeRAID controller is installed in the server, when this LED is

flashing slowly (one flash per second), it indicates that the drive is being rebuilt.

When the LED is flashing rapidly (three flashes per second), it indicates that the

controller is identifying the drive.

Chapter 1. The System x3500 M4 server 13

vDVD drive activity LED: When this LED is lit, it indicates that the DVD drive is

in use.

vDVD eject button: Press this button to release a DVD or CD from the DVD

drive.

vLight path diagnostics panel: Light path diagnostics is a system of LEDs on

various external and internal components of the server. When an error occurs,

LEDs are lit throughout the server. By viewing the LEDs in a particular order, you

can often identify the source of the error. See “Light path diagnostics panel” on

page 15 for more information about the light path diagnostics.

vOperator information panel: This panel contains controls and LEDs that provide

information about the status of the server. For information about the controls and

LEDs on the operator information panel, see “Operator information panel.”

vRemind button: This button places the system-error LED/check log LED on the

operator information panel into Remind mode. In Remind mode, the system-error

LED flashes once every 2 seconds until the problem is corrected, the server is

restarted, or a new problem occurs.

By placing the system-error LED indicator in Remind mode, you acknowledge

that you are aware of the last failure but will not take immediate action to correct

the problem. The remind function is controlled by the IMM2.

vReset button: Press this button to reset the server and run the power-on

self-test (POST). You might have to use a pen or the end of a straightened paper

clip to press the button. The Reset button is in the lower-right corner of the light

path diagnostics panel.

vUSB connectors: Connect a USB device, such as a USB mouse or keyboard to

any of these connectors.

Operator information panel

The following illustration shows the controls and LEDs on the operator information

panel.

System error LED

Check log LED

System locator LED

Power-on LED Ethernet activity LED

vPower-on LED: When this LED is lit and not flashing, it indicates that the server

is turned on. The states of the power-on LED are as follows:

Off: Power is not present or the power supply, or the LED itself has failed.

Flashing rapidly (4 times per second): The server is turned off and is not

ready to be turned on. The power-control button is disabled. This will last

approximately 5 to 10 seconds.

Flashing slowly (once per second): The server is turned off and is ready to

be turned on. You can press the power-control button to turn on the server.

Lit: The server is turned on.

vEthernet activity LEDs: When any of these LEDs is flashing, they indicate that

the server is transmitting to or receiving signals from the Ethernet LAN that is

connected to the Ethernet port that corresponds to that LED.

vSystem-locator LED: Use this blue LED to visually locate the server among

other servers. You can use IBM Systems Director to light this LED remotely. This

LED is controlled by the IMM2. When you light the system-locator LED, the LED

will blink and it will continue to blink until you turn it off.

14 IBM System x3500 M4 Type 7383: Installation and User’s Guide

vCheck log LED: When this amber LED is lit, it indicates that a system error has

occurred. Check the error log for additional information. See the Problem

Determination and Service Guide System x Documentationon the CD for more

information about error logs.

vSystem-error LED: When this amber LED is lit, it indicates that a system error

has occurred. An LED on the light path diagnostics panel is lit to help isolate the

error. This LED is controlled by the IMM2.

The following table describes the LEDs on the operator information panel and

suggested actions to correct the detected problems.

LED Description Action

System locator (blue) Use this LED to visually locate the server

among other servers. You can use IBM

Systems Director or IMM2 to light this LED

remotely.

Check log (amber) An error has occurred and cannot be

isolated without performing certain

procedures.

1. Check the IMM2 system event log and

the system-error log for information

about the error.

2. Save the log if necessary and clear the

log afterwards.

System-error (amber) An error has occurred. 1. Check the light path diagnostics LEDs

and follow the instructions.

2. Check the IMM2 system event log and

the system-error log for information

about the error.

3. Save the log if necessary and clear the

log afterwards.

Light path diagnostics panel

The following illustration shows the front LEDs on the light path diagnostics panel.

The light path diagnostic panel can be seen from the front bezel.

Note: The light path diagnostics LEDs remain lit only while the server is connected

to power.

For more information about the LEDs on the light path diagnostics panel, see “Light

path diagnostics LEDs” on page 16.

The following illustration shows the LEDs on the light path diagnostics panel.

Chapter 1. The System x3500 M4 server 15

OVER

SP EC

USB ports

Hard disk drive/RAID

Fan

Temperature

Microprocessor

Configuration

Memory

Power supply

PCI

System board

NMI

Over spec

Light path diagnostics LEDs: The following table describes the LEDs on the light

path diagnostics panel and suggested actions to correct the detected problems.

Table 2. Light path diagnostics panel LEDs

vFollow the suggested actions in the order in which they are listed in the Action column until the problem

is solved.

vIf an action step is preceded by "(Trained technician only)," that step must be performed only by a trained

technician.

LED Description Action

Hard disk drive/

RAID

A hard disk drive has failed or is

missing. A SAS controller or a

ServeRAID controller error has

occurred.

1. Check the LEDs on the hard disk drives for the drive with

a lit status LED and reseat the hard disk drive.

2. Reseat the hard disk drive backplane.

3. Check the LEDs near SAS controllers or ServeRAID

controllers and reseat the corresponding controllers.

4. For more information, see the “Hard disk drive problems”

under the Troubleshooting tables in the Problem

Determination and Service Guide.

5. If the error remains, replace the following components one

at a time, in the order listed, restarting the server after

each:

a. Replace the hard disk drive.

b. Replace the hard disk drive backplane.

c. Replace the SAS controller.

d. Replace the ServeRAID controller.

6. If the problem remains, go to http://www.ibm.com/systems/

support/supportsite.wss/docdisplay?brandind=5000008

&lndocid=SERV-CALL.

Fan

A fan has failed, is operating too

slowly, or has been removed. The

TEMP LED might also be lit.

1. Open the fan cage cover to reseat the failing fan (with lit

LED).

2. Replace the failing fan (see “Installing a simple-swap fan”

on page 63).

16 IBM System x3500 M4 Type 7383: Installation and User’s Guide

Specyfikacje produktu

Marka:	Lenovo
Kategoria:	serwer
Model:	System x3500 M4
Wysokość produktu:	440 mm
Szerokość produktu:	218 mm
Głębokość produktu:	750 mm
Waga produktu:	25000 g
Ilość portów Ethernet LAN (RJ-45):	5
Taktowanie procesora:	2.4 GHz
Typ procesora:	Rodzina procesorów Intel® Xeon® E5
Model procesora:	E5-2609
Karta graficzna:	G200eR2
Liczba portów USB 2.0:	8
Przewodowa sieć LAN:	Tak
Usługa RAID:	Nie
Producent procesora:	Intel
Liczba rdzeni procesora:	4
Typ pamięci wewnętrznej:	DDR3-SDRAM
Pamięć wewnętrzna:	4 GB
Zainstalowany system operacyjny:	Nie
Maksymalna pojemność pamięci:	768 GB
Gniazdo procesora:	LGA 2011 (Socket R)
Procesor:	Intel® Xeon®
Układ płyty głównej:	Intel® C602J
Poziomy raid:	0, 1,10
Typ BIOS:	UEFI
Technologia okablowania:	10/100/1000Base-T(X)
Zasilanie:	750 W
Maksymalna liczba procesorów SMP:	2
Gniazda PCI Express x16 (Gen 3.x):	3
Wspierane interfejsy dysków twardych:	SAS, Serial ATA
Liczba obsługiwanych HDD:	8
Rodzaj interfejsu sieci Ethernet:	Fast Ethernet, Gigabit Ethernet
Kontroler LAN:	Intel® I350-AM4
Liczba portów VGA (D-Sub):	1
System operacyjny:	Microsoft Windows Server 2008 R2, 2008, Red Hat Enterprise Linux 5 & 6, SUSE Linux Enterprise Server 10 & 11, VMware vSphere 5
Rodzina adaptera graficznego:	Matrox
Korekcja ECC:	Tak
Pamięć karty graficznej podsystemu graficznego:	16 MB
Gniazda pamięci:	24x DIMM
Rozmiar HDD:	2.5 "
Całkowita pojemność przechowywania:	0 GB
Obsługiwane rozmiary dysków twardych:	2.5 "
Procesor ARK ID:	64588
Technologia Intel® Hyper Threading (Intel® HT Technology):	Nie
Technologia Intel® Turbo Boost:	Nie
Technologia Intel® Quick Sync Video:	Nie
Technologia Intel® InTru™ 3D:	Nie
Technologia Intel® Clear Video HD (Intel® CVT HD):	Nie
Nowe instrukcje AES (Intel® AES-NI):	Tak
Technologia Udoskonalona Intel SpeedStep:	Tak
Technologia Intel® Trusted Execution:	Tak
Maksymalna konfiguracja CPU:	2
Intel® Enhanced Halt State:	Tak
Intel® Clear Video Technology dla MID (Intel® CVT for MID):	Nie
Intel® VT-x with Extended Page Tables (EPT):	Tak
Intel® Secure Key:	Tak
Intel® 64:	Tak
Technologia Wirtualizacji Intel® (Directed I/O) (VT-d):	Tak
Technologia Intel® Clear Video:	Nie
Wersja technologii Intel® Secure Key:	1.00
Technologia virtualizacji Intel® (VT-x):	Tak
Wersja Intel® TSX-NI:	0.00
Hot-swap:	Tak
Interfejs HDD:	Serial ATA, Serial Attached SCSI (SAS)
Maksymalna pojemność przchowywania:	32 TB
Liczba procesorów:	1
Typ pamięci procesora:	Smart Cache
Cache procesora:	10 MB
Wskaźnik magistrali systemowej:	6.4 GT/s
Maksymalne taktowanie procesora:	2.50 GHz
Litografia procesora:	32 nm
Liczba wątków:	4
Tryb pracy procesora:	64-bit
Nazwa kodowa procesora:	Sandy Bridge EP
Maksymalna pamięć wewnętrzna wspierana przez procesor:	750 GB
Typy pamięci wspierane przez procesor:	DDR3-SDRAM
Taktowanie zegara pamięci wspierane przez procesor:	800,1066 MHz
Przepustowość pamięci obsługiwana przez procesor ( max ):	34.1 GB/s
Kanały pamięci wspierane przez procesor:	Cztery
Pamięć ECC wspierana przez procesor:	Tak
Maksymalna liczba linii PCI Express:	40
Konfiguracje PCI Express:	x4, x8, x16
Termiczny układ zasilania (TDP):	80 W
Bezkonfliktowy procesor:	Nie
Stepping:	M1
Instrukcje obsługiwania:	AVX
Technologia Execute Disable Bit (EDB):	Tak
Stan spoczynku:	Tak
Technologie Thermal Monitoring:	Tak
Skalowalność:	2S
Wbudowane opcje dostępne:	Nie
Typ magistrali:	QPI
Wielkość opakowania procesora:	52.5 x 45.0 mm
Moduł TPM (Trusted Platform Module):	Tak
Układ pamięci:	1 x 4 GB
Prędkość zegara pamięci:	- MHz
Karta graficzna on-board:	Tak
Obsługa zasilania zapasowego (RPS):	Tak
Liczba głównych źródeł zasilania:	1
Szeregowe porty komunikacyjne:	1
Wersja gniazd typu Slot (PCI Express):	3.0
Parytet FSB:	Nie
Tcase:	70 °C
Magistrala systemowa:	- MHz
Seria procesora:	Intel Xeon E5-2600
Intel® Wireless Display (Intel® WiDi):	Nie
Technologia Intel® My WiFi (Intel® MWT):	Nie
Technologia Intel® Identity Protection (Intel® IPT):	Nie
Technologia Intel® Anti-Theft (Intel® AT):	Nie
Intel® Insider™:	Nie
Technologia Intel® FDI:	Nie
Intel® Flex Memory Access:	Nie
Intel® Fast Memory Access:	Nie
Intel® Demand Based Switching:	Tak
Układ graficzny i litografia IMC:	32 nm
Technologia Intel® Dual Display Capable:	Nie
Intel® Rapid Storage Technology:	Nie
Wersja technologii Intel® Identity Protection:	0.00
Napędy optyczne:	DVD-ROM
Technologia Intel® Virtualization (Intel® VT):	VT-d, VT-x
Współczynnik Magistrala/Rdzeń:	24
Mapa typów obrazów:	<div><img src="https://ark.intel.com/inc/images/diagrams/diagram-18.gif" title="Block Diagram" /></div>
Rozszerzenie PAE (Physical Address Extension):	46 bit
Wewnętrzne kieszenie na napęd:	5.25" x 2, 2.5" x 8
Liczba linków QPI:	2
PCI Express x8 slots:	5