Instrukcja obsługi Lenco IPT-2

Lenco podstawa/stacja dokująca IPT-2

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Lenco IPT-2 (19 stron) w kategorii podstawa/stacja dokująca. Ta instrukcja była pomocna dla 20 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/19

HIGH POWER SPEAKER

WITH iPod/iPhone DOCKING STATION,

FM PLL RADIO & CARDSLOT

MODEL: IPT-2

INSTRUCTION MANUAL

Please read these instructions while operating your unit.

Manufacturer of this unit follows a principle of constant improvement and is not held

responsible for any changes that are made to the unit nor accepts any liabilities

for these changes. Thanks for your choice of our products.

For information and support, www.lenco.eu

17 19

18 18

MAIN UNIT

1. PREV/FAST BACKWARD/TUNE-

BUTTON

2. STOP BUTTON

3. IPOD DOCKING

4. NEXT/FASTFORWARD/TUNE+ BUTTON

5. PLAY/PAUSE BUTTON

6. VOLUME CONTROLLER

8. STORE BUTTON

9. PRESET UP BUTTON

10. PRESET DOWN BUTTON

11. TONE BUTTON

12. LCD DISPLAY

13. STANDBY BUTTON

14.

15. MUTE BUTTON

16. PTY BUTTON

17. SD/MMC CARD SLOT

18.

19. VIDEO OUT JACK

20. FM ANTENNA

21. RIGHT AUX IN JACK

22. LEFT AUX IN JACK

23. POWER ON/OFF BUTTON

24. AC SOCKET

REMOTE SENSOR

FUNCTION BUTTON

STAND FEET

REMOTE CONTROL

2. INFO BUTTON

4. PREV/FASTBACKWARD BUTTON

5. NEXT /FAST FORWARD BUTTON

6. M+ BUTTON

7. TUNE- BUTTON

8. ENTER BUTTON

9. NUMERIC BUTTON

10. STORE BUTTON

11. VOL- BUTTON

12. BUTTON

13. MUTE BUTTON

14. PLAY/PAUSE BUTTON

15. STOP BUTTON

16. TUNE+ BUTTON

17. M- BUTTON

18. MENU BUTTON

19. PTY BUTTON

20. RAN BUTTON

21. REP/ST BUTTON

22. TONE BUTTON

23. VOL+ BUTTON

FUNCTION BUTTON

SLEEP BUTTON

STANDBY

POWER SUPPLY

NOTE:

SLEEP FUNCTION

Plug one end of the AC cord into the AC socket on the unit, then plug the other end into the

AC wall outlet.

During playback, if not any operation in 6 hours, the unit will switch to standby mode

automatically.

Press a SLEEP button on the remote in power on mode. Each time SLEEP button is pressed,

the LCD display changes Sleep time in a sequence as follows:

90 80 70 60 50 40 30 20 10 off

The player goes to standby mode in the moment playback or broadcasting reaches the set

Sleep time.

1. Dock an iPod onto the unit.

2. Press the POWER ON/OFF button on the rear of the unit and press STANDBY button to

turn the unit on.

3. Press the FUNCTION button continuously to toggle the unit to iPod mode.

4. Press PLAY/PAUSE button to play and pause the docked iPod .

5. During normal playback, Press PREV/NEXT button to skip the tracks ahead or backward.

Long press the NEXT or PREV button to search through the current track at a high speed

forward or backward.

6. Press MENU button on the remote to return back the menu the inserted iPod.

7. Use STOP button to cease the iPod playback.

There is a video output jack on the rear of the unit, so that you could make the video output to

a TV set or other appliance with video input jack for enjoying video. To output the video,

connect one end of the video cable(included) to the video output jack of the unit, the other

end to the video input jack of the appliance.

1. Press the POWER ON/OFF button on the rear of the unit and press STANDBY button to

turn the unit on.

2. Press and release the FUNCTION button continuously to switch the unit to radio mode (the

radio frequency is shown on the LCD display).

3. Press PREV or NEXT button on the main unit or TUNE+/- button on the remote to tune the

radio. Press and hold PREV/NEXT button on the unit or TUNE-/+ button on the remote to

automatically tune the radio frequency backward and forward respectively . When the tuning

goes to one available station, broadcasting starts immediately.

4. Press REP/ST button on the remote to switch the radio between FM(MONO) and FM(ST).

If the signal is not strong enough, you cannot select FM(ST).

5. If the unit broadcast a program with RDS, the RDS icon will be shown on the LCD display.

Press INFO button on the remote to check the frequency of the current station.

iPod OPERATING

PLAYING AN iPod

VIDEO OUTPUT FOR iPod

FM RADIO

TUNING THE FM RADIO

10 21

SAVING FM RADIO STATIONS TO THE UNIT'S MEMORY

PTY BUTTON

PLAYING THE EXTERNAL STORAGE MEDIA DEVICE (SD/MMC CARD)

TONE SETTING FOR THE UNIT

MUTE THE UNIT

1. After tuning the FM radio to the desired stations, press STORE button until "MEM" is shown

on the LCD display with a flashing number of a memory cell.

2. Press the M+/ M- button on the remote or press PRESET UP/DOWN button on the unit to

select the radio memory cell.

3. Press STORE button again to save the current radio station to the selected memory cell.

4. To recall the preset station frequency, press M+ or M- button on the remote or PRESET

UP/DOWN button on the unit repeatedly.

If you want to tune to a radio station of your favorite type, please set the program type first

before tuning. Press and hold PTY button until a certain program type flashes on the LCD

display.

Select your desired program type by pressing PTY button repeatedly until your desired

program type shows on the screen, then press PREV/NEXT button on the unit or TUNE-/+

button on the remote to start tuning. When a station of the selected program type, the unit will

broadcast it immediately.

1. Power on the unit. Insert a SD/MMC card onto the unit, and press FUNCTION button

repeatedly until toggle the unit to card mode.

2. After the unit scan the inserted card, playback will start automatically.

3. Press REP/ST button repeatedly to change the play mode.

4. Press RAN button to play the inserted media device in the random order, press the button

again to exit random play.

5. Press PLAY/PAUSE button to pause playback, press the button again to resume normal

play.

6. During playback, short press NEXT button or PREV button to skip the track forward or

backward.

Long press the NEXT or PREV button to search through the current track at a high speed

forward or backward.

7. Press numeric buttons to select your favorite track directly.

Note: The card reader can only play MP3 files.

During playback, press TONE button once, and use VOL+/-button on the remote or VOLUME

CONTROLLER on the unit to adjust the bass. Press TONE button twice repeatedly for

adjusting treble effect by pressing VOL+/- button on the remote or rotate VOLUME

CONTROLLER on the unit as adjust bass effect. After adjusting the treble effect, press the

TONE button again to resume the previous display.

During playback, press MUTE button to switch off the audio output. Press the button again to

resume normal play.

AUX IN

IMPORTANT SAFETY INSTRUCTIONS

Your player can be used as a power amplifier to playback an audio signal from portable radio,

TV set or MP3 player or whatever provided this appliance is so designed that audio signal may

be produced through a LINE-OUT jack or the like.

Observe the following steps to connect the player to another appliance:

1. Connect the appliance into the player's left & right AUX IN jacks with the supplied LINE OUT

cables.

2. Press STANDBY button to turn the unit on.

3. Press FUNCTION button repeatedly to switch the unit to AUX mode.

4. Power on the appliance and begin play.

At this time you will be able to hear the sound produced from the connected appliance.

Speaker Size: AROUND 3.0 INCH SUB 6.5 INCH

Dimensions: 305(L) x 315(W) x 933(H)mm

Operating Humidity Range:10 % to 75 %

Compatible with SD/MMC CARD

If at any time in the future you should need to dispose of this product please note

that: Waste electrical products should not be disposed of with household waste.

Please recycle where facilities exist. Check with your Local Authority or retailer for

recycling advice. (Waste Electrical and Electronic Equipment Directive)

The apparatus shall not be exposed to dripping or splashing and that no objects filled with

liquids, such as vases, shall be placed on the apparatus.

When the mains plug or an appliance coupler is used as the disconnect device, the disconnect

device shall remain readily operable. To be completely disconnected the power input, the

mains plug of the apparatus or the appliance coupler shall be disconnected from the mains

completely.

No naked flame sources, such as lighted candles, should be placed on the apparatus.

Minimum distances 2.0cm around the apparatus for sufficient ventilation. The ventilation

should not be impeded by covering the ventilation openings with items, such as newspapers,

table-cloths, curtains, etc.

The use of apparatus is in tropical and/or moderate climates.

Attention should be drawn to the environmental aspects of battery disposal.

Danger of explosion if battery is incorrectly replaced. Replace only with the same

or equivalent type.

Battery shall not be exposed to excessive heat such as sunshine, fire or the like.

The marking plate is located at the back of the apparatus.

Power source: AC 230V 50Hz

Power consumption: 90W

Remote control: AAA1.5V x 2

Receiving bands: FM 87.5 -108 MHz

CAUTION:

SPECIFICATIONS

Specyfikacje produktu

Marka:	Lenco
Kategoria:	podstawa/stacja dokująca
Model:	IPT-2
Kolor produktu:	Czarny
Rodzaj zasilania:	Prąd przemienny
Częstotliwość wejściowa AC:	50 Hz
Napięcie wejściowe AC:	230 V
Wysokość produktu:	933 mm
Szerokość produktu:	315 mm
Głębokość produktu:	305 mm
Waga produktu:	9000 g
W zestawie pilot zdalnego sterowania:	Tak
Podręcznik użytkownika:	Tak
Bluetooth:	Nie
Moc wyjściowa (RMS):	90 W
Typ ekranu:	LCD
Obsługiwane typy kart pamięci:	MMC, SD
Przewody:	AV
Pobór mocy w trybie czuwania:	0.9 W
Kanały wyjścia audio:	2.1 kan.
Ilość stacji:	10
Pobór mocy:	70 W
Wejście AUX:	Tak
Kompatybilność dokowania produktów Apple:	iPhone, iPod
Zasięg częstotliwości:	- Hz
Radio FM:	Tak
Dołączony tuner RDS:	Tak
Wyłącznik czasowy:	Tak
Typ głośnika niskotonowego:	Subwoofer aktywny