Instrukcja obsługi Lectrosonics DNT0212
Lectrosonics
edytor
DNT0212
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Lectrosonics DNT0212 (20 stron) w kategorii edytor. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/20
DNT Series
DNT16i/DNT0212 Network Processors
INSTALLATION AND STARTUP GUIDE
Rio Rancho, NM, USA
www.lectrosonics.com
Fill in for your records:
Serial Number:
Purchase Date:
A trademark of Audinate Pty Ltd.
DNT Digital Processor
LECTROSONICS, INC.
2
Installation and Quick Start Guide
Rio Rancho, NM 3
Table of Contents
FCC Part 15 Compliance 3 .......................................................
Important
Safety Instructions 4 .........................................................
Overview 5 .................................................................................
What is Dante? 5 ....................................................................
About the DNT Processors 5 ..................................................
Switched and Redundant Modes 5 .........................................
DNT16i Front Panel 6 ................................................................
DNT16i Rear Panel 6 .................................................................
DNT0212 Front Panel 7 .............................................................
DNT0212 Rear Panel 7 ..............................................................
DNT Control Panel Software 8 .................................................
DNT Software Installation 8 .....................................................
About Dante Software 9 ...........................................................
DanteTM Software
Installation 9 ......................................................................
Mandatory Settings 10 .............................................................
Dante Controller Software - Network Settings 10 ...................
DNT Control Panel Software - Signal Flow Configuration 11 ..
DNT Software - USB Connection 11 .......................................
DNT Software - Ethernet Connection 11 ................................
Hardware Connections 12 .......................................................
Installing the chassis into a rack 12 ........................................
Connecting via USB for the First Time 12 ...............................
Setup and Control Port Connections 12 .................................
Programmable Inputs 13 .........................................................
RS-232 Serial Port Wiring 13 ..................................................
Crestron® RS-232 Port Wiring 13 ............................................
Programmable Outputs 13 ......................................................
Network and PC Connections 14 ............................................
Signal Routing 15 .....................................................................
Replacement Parts and Accessories 16 .................................
Service and Repair 17 ..............................................................
Returning Units for Repair 17 .................................................
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. The equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that which the receiver is
connected
• Consult the dealer or an experienced radio/TV technician for help
Changes or modifications to this equipment not expressly approved by Lectrosonics, Inc. could
void the user’s authority to operate it.
Specyfikacje produktu
| Marka: | Lectrosonics |
| Kategoria: | edytor |
| Model: | DNT0212 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Lectrosonics DNT0212, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje edytor Lectrosonics
7 Października 2024
5 Października 2024
5 Października 2024
Instrukcje edytor
- edytor Hikvision
- edytor Roland
- edytor Bose
- edytor Asus
- edytor Allen & Heath
- edytor HP
- edytor Heritage Audio
- edytor Datapath
- edytor Zoom
- edytor TC Helicon
- edytor Vivolink
- edytor Eventide
- edytor DBX
- edytor Smart-AVI
- edytor Ashly
- edytor Gefen
- edytor SEADA
- edytor Radial Engineering
- edytor Neutrik
- edytor SPL
- edytor RGBlink
- edytor Rupert Neve Designs
- edytor Dangerous Music
- edytor Matrox
- edytor Intel
- edytor Golden Age Project
- edytor Sonifex
- edytor Solid State Logic
- edytor Mathew Lane
- edytor Warm Audio
- edytor Drawmer
- edytor SIIG
- edytor Manley
- edytor MuxLab
- edytor Helix
- edytor Christie
- edytor Rane
- edytor AMD
- edytor Lexicon
- edytor Empirical Labs
- edytor AudioThing
- edytor Avenview
- edytor FabFilter
- edytor Metric Halo
- edytor Henry Engineering
- edytor MyMix
Najnowsze instrukcje dla edytor
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
7 Października 2024
7 Października 2024
7 Października 2024