Instrukcja obsługi LC-Power LC-DOCK-U3-II

LC-Power podstawa/stacja dokująca LC-DOCK-U3-II

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla LC-Power LC-DOCK-U3-II (3 stron) w kategorii podstawa/stacja dokująca. Ta instrukcja była pomocna dla 24 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/3

Installation guide

LC-DOCK-U3-II - USB 3.0 Dual Bay Docking Station for 2x 2,5”/3,5” SATA HDDs/SSDs

-----------------------------------------------------------------------------------------------------------------------------------------------------------------

1. Included in delivery

● USB 3.0 dual bay docking station

● USB 3.0 cable

● Power adapter

● Installation guide

3. Information – please read carefully before using the product

We strongly advise that you make a backup of your original data before commencing the cloning process

to avoid any data loss in case of a power failure during the cloning process. LC-Power cannot accept the

responsibility for the loss of data or the misuse of the device. Please also check the content of the

package before commencing with the use of the device.

Minimum system requirements

- Intel Pentium II 50MHz compatible or Mac G3 processor or higher

- Microsoft Windows 2000/XP/Vista/7/8/10, Mac OS 9.1, 9.2, 10.1.5, 10.2, 10.3 or higher

- Computer supporting USB 3.0

Page 1

Product overview

1. Hardware clone button

3. HDD B bay (Target drive bay)

5. Cloning status LEDs

7. Power socket (input DC 12V/3A)

2. Main features

Supports 2,5” & 3,5” SATA HDDs/SSDs

2,5” up to 1TB, 3,5” up to 4TB

Supports hardware cloning

USB 3.0 output interface

Easy installation, plug & play and

hot- swappable

Including LED indicator for working status

2. HDD A bay (Source drive bay)

4. HDD A & B LEDs

6. USB 3.0 port

8. Power switch

Installation guide

LC-DOCK-U3-II - USB 3.0 Dual Bay Docking Station for 2x 2,5”/3,5” SATA HDDs/SSDs

-----------------------------------------------------------------------------------------------------------------------------------------------------------------

4. Formatting a hard disk drive

If you are using new/unformatted hard disk drives, you will first need to format and partition the drives

before your operating system will recognize them. Please refer to the documentation included with your

hard disk drive and/or operating system for more information about correctly formatting a hard drive.

5. Docking station operation

The dual bay docking station primarily functions as a 2-bay docking station that allows you to easily

connect up to two hard disk drives to your computer through a single USB 3.0 connection.

1. Before your power on and use the docking station, please insert your SATA hard disk drive(s) into the

HDD A bay and/or HDD B bay. Be sure that the hard disk drives’ SATA connectors align with the SATA

connectors inside the HDD bays.

2. Use the provided USB 3.0 cable to connect the docking station with a USB port on your computer.

3. Press the power button located on the rear side of the docking station. The LED indicator will light up

and the hard disk drives will be powered up.

4. Your computer will automatically detect the newly connected device and drives. It may need one to

two minutes to install the necessary drivers. The docking station uses drivers that are already built

into your operating system. Additional drivers are not required.

5. Once the computer has recognized the drives, they will show up under “Computer” (Windows) or on

your desktop (Mac OS X).

Note : Do not remove the hard disk drives from the docking station or disconnect the docking

station from the USB port of your computer while copying files to or from the device or while

files or applications stored on the hard disk drive are in use. Otherwise you are in danger of a

loss of data!

6. Hardware clone function (hard disk drive duplication)

To successfully use the clone function, the capacity of the target hard disk drive must be equal to or larger

than the capacity of the source hard disk drive. Please note that data cannot be cloned to a hard disk

drive with a smaller capacity than the original source hard disk drive.

Hardware clone mode

Please use the one button cloning feature (from source hard disk drive to target hard disk drive) without

connecting the docking station to a computer.

Page 2

Installation guide

LC-DOCK-U3-II - USB 3.0 Dual Bay Docking Station for 2x 2,5”/3,5” SATA HDDs/SSDs

-----------------------------------------------------------------------------------------------------------------------------------------------------------------

Important note :

1. Before cloning a hard disk drive, please the from the docking station. disconnect USB 3.0 cable

If the mentioned cable is connected during the cloning process, it may cause data corruption on

the hard disk drives.

2. Please make sure you put the correct hard disk drive into the correct HDD bay before cloning.

Otherwise this may cause a data loss.

The capacity of the target hard disk drive (must be put in the target HDD bay) must be equal or

larger than the capacity of the source hard disk drive.

Please follow the steps below to enable the hardware clone process:

1. Install two hard disk drives into the dock. Make sure the correct drives are properly installed to source

bay (HDD A) and target bay (HDD B).

2. Remove the USB cable from the docking station, connect the power adapter and press the power

button to power on the docking station.

3. Press and hold the button for to start the duplication. The percentage LED CLONE 3 seconds

indicators located next to the “Clone” button will begin to blink. If you do not hold the clone button for

3 seconds, you need to start the process again.

4. As the duplication process progresses, the LED indicator will blink green and will change the colour

regarding the cloning status (25% = green, 50% = red, 75% = yellow, 100% = orange).

5. When the duplication process has completed, the percentage LED indicator will stop blinking and stay

orange lighted continuously. Press the power button on the rear side of the docking station to turn off

the docking station.

6. You can now safely remove the hard disk drives from the docking station.

Silent Power Electronics GmbH, Formerweg 8, 47877 Willich, Germany, www.lc-power.com

Page 3

Specyfikacje produktu

Marka:	LC-Power
Kategoria:	podstawa/stacja dokująca
Model:	LC-DOCK-U3-II
Kolor produktu:	Czarny
Wysokość produktu:	80 mm
Szerokość produktu:	142 mm
Głębokość produktu:	102 mm
Waga produktu:	330 g
Maksymalna szybkość przesyłania danych:	5 Gbit/s
Kod zharmonizowanego systemu (HS):	84733080
Waga wraz z opakowaniem:	720 g
Diody LED:	Progress, Status
Interfejs napędów pamięci masowej:	SATA
Obsługiwane rozmiary dysków pamięci:	2.5, 3.5 "
Materiały:	Aluminium, Metal, Plastic
Standardowe interfejsy:	USB 3.2 Gen 1 (3.1 Gen 1)
Typ nośników pamięci:	HDD
Interfejs hosta:	USB 3.2 Gen 1 (3.1 Gen 1) Type-B
Hot-swap:	Tak
Maksymalna pojemność przchowywania:	4 TB
Ilość portów USB 3.2 Gen 1 (3.1 Gen 1):	1