Instrukcja obsługi Kathrein EXR 2998

Kathrein przełącznik EXR 2998

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Kathrein EXR 2998 (3 stron) w kategorii przełącznik. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/3

QCascadable multi-switch for splitting 8 Sat levels and

terrestrial signals to multiple receivers

QOnly one downlink per receiver needed (two for twin

receivers)

QFacility to select horizontal/vertical, low/high, Sat position A/

position B independently for each receiver using DiSEqC™

controls

QIf not using DiSEqC™ controls, changing the horizontal/

vertical, low/high of Sat position A can be performed, also by

tone burst changing Sat position A/position B

QIntegral ampliﬁ er for low attenuation in Sat signal band

QIntegral pre-emphasis to equalise cable attenuation

QTerrestrial signals also receivable with Sat receiver switched

off

QTerrestrial band: 5-862 MHz, passive

QHigh degree of insulation between outputs

QCan be remote fed via the horizontal low inputs.

All other inputs are voltage-free (enabling operation with

UAS 485)

QFor indoor mounting

EXR 2908

QMulti-switch for 8 connections, with integral power supply unit

QLow power consumption based on high-efﬁ ciency short-

circuit-proof switch-mode power supply unit

QCan be extended using EXR 2998

EXR 2998

QMulti-switch loop-through for system extension with eight

connections each

QHighly cascadable (up to 40 connections)

Sat-IF splitting system (8 x Sat-IF)

Multi-switch

EXR 2908

EXR 2998

20510019

20510020

Multi-switch

936.3280/ /0 09/1.3eB 8

Setting Effect

22 kHz High/Low All inputs position “A” can be selectedĺ

Tone Burst Pos. A/B All inputs position “A” and “B” can be selectedĺ

*) The terms for the settings in the receiver menus are speciﬁ c to the respective model and manufacturer!

Settings for receivers without DiSEqC™

Setting Effect

DiSEqC™ “On” All inputs can be selected

22 kHz and tone burst to “Off” Changeover time is shortened

Settings for receivers with DiSEqC™

EXR 2908

20510019

EXR 2998

20510020

Technical data

Type EXR 2908 EXR 2998

Order no. 20510019 20510020

Subscriber connections 8 8

Inputs 1 x terr. 8 x Sat-IF 1 x terr. 8 x Sat-IF

Frequency ranges MHz 5-862 950-2150 5-862 950-2150

Through loss dB - - 3.5 1-2.5 ¹ )

Attenuation ¹)dB 10-13 5-0 13-16 5-0

Horizontal/vertical isolation dB - 25 - 25

Subscriber isolation dB 25 25 25 25

Max. output level ²)dBµV - 109 - 109

Screening factor dB

5-300 MHz > 85

300-470 MHz > 80

470-1000 MHz > 75

1000-2150 MHz > 55

Control with DiSEqC™ Vert./horiz., low/high, pos. A/B

Controls without DiSEqC™

- with 14/18 V and 0/22 kHz

- with tone burst

Vert./horiz., low/high, (pos. A)

Pos. A/B

Current consumption per subscriber mA 30

Nominal input voltage V 198-253 -

Nominal input power (800/400 mA load) W 18.1 / 10 -

Secondary voltage ³)V 18 -

Max. total remote feed current ³)mA 800 -

Max. remote feed current per trunk mA - 1000

Protection class/protection type II (totally insulated)/IP 30 IP 30

Permissible ambient temperature °C - 20 to + 55 - 20 to + 55

Connections F-connectors F-connectors

Dimensions (W x H x D) mm 227 x 228 x 44 172 x 228 x 44

Packing unit/Weight units/kg 1 (10)/1.0 1 (10)/0.85

¹)

Frequency-dependent attenuation

²)

SAT to EN 50083-3, 35-dB-IMA

³)

Via horizontal low inputs

936.3280/ /0 09/2.3eB 8

Reception range Position A/satellite 1 (e.g. ASTRA) Position B/satellite 2 (e.g. EUTELSAT)

Low band High band Low band High band

Vertical Horizontal Vertical Horizontal Vertical Horizontal Vertical Horizontal

Command E2 10 38 F0 E2 10 38 F2 E2 10 38 F1 E2 10 38 F3 E2 10 38 F4 E2 10 38 F6 E2 10 38 F5 E2 10 38 F7

DiSEqC™ commands, e.g. for Kathrein measuring instrument MSK 25 or MSK 33

• The equipment described is designed solely for the installation of satellite receiver systems.

• Any other use, or failure to comply with these instructions, will result in voiding of warranty cover.

• The equipment may only be installed in dry indoor areas. Do not mount on or against highly combustible

materials.

• The equipment must be provided with an earthing wire (Cu, at least 4 mm2).

• The safety regulations set out in the current EN 60728-11 and EN 60065 standards must be complied with.

• Fixings: Wood screws, max Ø: 4.5 mm

• Connector: HF plug 75 (series F) to EN 61169-24.

•Unused subscriber ports should be closed off by 755 Ohm resistors (e.g. EMK 03).

Current-carrying unit

• Do not open or tamper with the unit!

• When working on the system always unplug the mains plug from the wall socket!

• Ensure adequate clearance! Min. 5 cm to all sides!

• Do not install overhead.

• Free circulation of air must be possible to discharge the heat emitted by the unit.

Risk of overheating!

• Permissible ambient temperature -20 to +55°C

Important:

• No liquid-ﬁ lled items may be placed on top of the power supply unit.

• The power supply unit must not be exposed to dripping or splashing water.

• The mains plug must be easily accessible and operable.

• The only reliable method of disconnecting the unit from the mains is to unplug it.

Electronic equipment - in accordance with directive 2002/96/EC OF THE EUROPEAN is not household waste

PARLIAMENT AND THE COUNCIL dated 27th January 2003 on used electrical and electronic equipment, it

must be disposed of properly.

At the end of its service life, take this unit for disposal to an appropriate ofﬁ cial collection point.

Installation and safety instructions

System example

936.3280/ /0 09/3.3e/ZWT Technical data subject to change.B 8

Terrestrial

antenna

(symbolic representation)

UAS 484 or

UAS 485

UAS 484 or

UAS 485

KATHREIN-Werke KG . Anton-Kathrein-Straße 1 – 3 . P.O. Box 100 444 . 83004 Rosenheim . GERMANY

. phone +49 8031 184-0 . Fax +49 8031 184-306

Internet: http://www.kathrein.de

• If the inner cable conductor diameter is

greater than 1.2 mm or in case of burr, the

device sockets may be destroyed.

Diameter

0.6-1.2 mm

free of burrs

Max. 2 mm excess

length

Clamping torque max.

3 Nm (danger of over-

winding)

Specyfikacje produktu

Marka:	Kathrein
Kategoria:	przełącznik
Model:	EXR 2998
Kolor produktu:	Metaliczny
Waga produktu:	900 g
W zestawie pilot zdalnego sterowania:	Nie
Podręcznik użytkownika:	Tak
Diody LED:	Nie
Adapter zewnętrznego zasilania:	Nie
Wymiary produktu (SxGxW):	172 x 228 x 44 mm
Możliwości montowania w stelażu:	Nie
Materiały:	Metal
Obsługa funkcji Plug & Play:	Tak
Wyjścia BNC:	8
Wejścia BNC:	9
Rodzaj portu wideo:	BNC
Connector type:	F