Instrukcja obsługi Kathrein EXD 154

Kathrein przełącznik EXD 154

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Kathrein EXD 154 (8 stron) w kategorii przełącznik. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/8
1 / 8
EXD 154
2050000003
Sat-IF Distribution System (4 x Sat-IF)
Digital Wideband Multi-switch
About This Manual
This document is part of the product.
►Do not install or use the device until you
have read and understood this document.
►Keep this document for reference throug-
hout the service life of the device and pass it
on to any new owner or user.
For the most up-to-date version of this docu-
ment, go to www.kathrein-ds.com.
Features
Universal multi-switch with automatic
operating mode detection. A standard TV or
16 receivers each can be operated in single
cable mode at each connection.
All types of signalling are supported and
automatically detected: 14/18 V 0/22 kHz
(legacy), DiSEqC™ 1.0, single cable stan-
dards according to EN 50494, as well as the
extended command set according to EN
50607 (SCD2 or JESS); PIN codes can also
be used in single cable operation.
Latest IC technology with full band captu-
ring ensures the best signal quality. The
inputs are broadband and can also be
operated with wideband LNBs (e.g. UAS
582). This means that a multi-feed system
can be implemented (for two LNBs, the TV
set must support either DiSEqC™ or the
single-cable standard).
QR code for user instructions
For indoor installation
The integrated AGC (Automatic Gain
Control) ensures that the Sat IF signals
have a constant output level and more
reserve in the distribution.
When all TV sets/receivers are switched
o, the multi-switch no longer consumes
any power. If Kathrein Power Saving is acti-
vated, the LNBs are also switched o.
suitable for DVB -T/T2
Wideband to Quatro mode:
In this case, the two inputs of the wideband
LNB are permanently connected to the four
outputs of the multi-switch. The outputs of
the EXD 154 behave like a Quatro LNB, so
that an additional standard multi-switch
can be connected.
The NCF 18 is a highly ecient, short-
circuit-proof switched-mode power supply
unit
Tip The QR code on the front of the
multi-switch will take you to our
website where you can download
these instructions:
111,6
134
148
159
2050000003
2 4
1 3
V low
V high
H high
Terr.
H low
18V
300mA ma x.
Pow er
Saving
Wideband
Universal
Wideband
Universal
ON
OFF
WB-Quatro
DC
42,5
2 / 8
Transport and Storage
►Use the original packaging for transporting
the device; store it in a dry place.
►Make sure there is no water condensation
build-up.
CAUTION!
Risk of damage to the device if operated in inappropriate ambient conditions!
►The equipment may only be installed in dry indoor areas. Do not install the equip-
ment on or against easily combustible material
►The equipment must be provided with an equipotential bonding wire (Cu, at least
4 mm2)
►The safety regulations set out in the current EN 60728-11 and EN 62368-1 standards
must be complied with
►Fasteners for concrete substrates and masonry: 4 suitable plugs and associated
screws with half-round or cylindrical head, outer thread diameter 4.5 - 5 mm, head
diameter ≥ 9 mm and a screw length ≥ 30 mm
For other types of wall, use the appropriate screws or screw-dowel systems, which
oer the same or better fastening
►Connectors: RF connectors 75 Ω (F series) compliant with EN 61169-24
►Unused subscriber ports should be closed o using 75 Ω resistors (e.g. EMK 03)
►To meet EMC requirements, the only power supply unit allower to be used is the
NCF 18
Risk of damage to property!
If the diameter of the inner cable conductor exceeds 1.2 mm or if there is a burr, the
device sockets may be damaged beyond repair.
Max. 2 mm
excess length
Clamping torque
max. 3.4 Nm
(danger of over-
winding)
Diameter
0.6 - 1.2 mm free of burrs
Mounting Instructions
Intended use
The equipment described is designed solely for the installation of satellite receiver systems.
Any other use or non-observance of these instructions will result in the loss of the warranty and
guarantee.
Scope of Delivery
●EXD 154
●Instructions for use for EXD 154
●NCF 18
3 / 8
Safety Precautions
Current-carrying device
►Do not open or tamper with the unit
►When working on the system, always unplug the power supply unit from the wall
socket.
►Ensure adequate clearance: at least 5 cm to all sides
►Do not install on the ceiling or vertically
►Ensure free circulation of air to dissipate the heat from the unit. Risk of overhea-
ting!
►Admissible ambient temperature: -20 to +40 °C
Note:
►Do not place any liquid-filled items on top of the device
►Do not expose the device to dripping or splashing water
►Ensure that the power supply unit is easily accessible and operable
►Disconnect the unit from the mains by pulling the plug of the power supply unit
out of the mains socket
SAT-IF Distribution Equipment (not for wideband operation!)
Type Kathrein Power Saving Switch Setting
VWS 2551 Amplifier Unrestrictedly usable ON
EBX 2520 Two-way splitter
Unrestrictedly usable if each trunk
is terminated by the Kathrein Power
Saving-capable end multi-switch
ON
EAX 2512 Two-way tap Not Kathrein Power Saving-capable OFF
VWS 2500 Amplifier Order no. 20510098 is Kathrein Power
Saving-capable; older models are not ON / OFF
To prevent the set user band from being used or disturbed by another subscriber, the user band can
be protected by means of a PIN code. The PIN code must be entered in the settings of the receiver/
TV. Each user band is assigned a fixed PIN.
PIN Code Protection
UB
1
UB
2
UB
3
UB
4
UB
5
UB
6
UB
7
UB
8
UB
9
UB
10
UB
11
UB
12
UB
13
UB
14
UB
15
UB
16
151 052 133 124 205 196 187 178 099 232 198 111 190 002 201 140

Specyfikacje produktu

Marka: Kathrein
Kategoria: przełącznik
Model: EXD 154

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Kathrein EXD 154, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje przełącznik Kathrein

Kathrein

Kathrein EXR 2998 Instrukcja

29 Września 2024
Kathrein

Kathrein EXR 2908 Instrukcja

3 Września 2024
Kathrein

Kathrein EXD 2532 Instrukcja

3 Września 2024
Kathrein

Kathrein VWS 2900 Instrukcja

1 Września 2024
Kathrein

Kathrein UWS 24 Instrukcja

31 Sierpnia 2024
Kathrein

Kathrein EXD 154 Instrukcja

28 Sierpnia 2024
Kathrein

Kathrein EBX 2920 Instrukcja

18 Sierpnia 2024
Kathrein

Kathrein EXR 121 Instrukcja

6 Sierpnia 2024
Kathrein

Kathrein EXR 1708 Instrukcja

3 Lipca 2024
Kathrein

Kathrein EXI 3591 Instrukcja

2 Lipca 2024

Instrukcje przełącznik

Najnowsze instrukcje dla przełącznik

Powerfix

Powerfix PSSS 2 A1 Instrukcja

14 Stycznia 2025
INOGENI

INOGENI CAM230 Instrukcja

14 Stycznia 2025
Schneider

Schneider CCT15225 Instrukcja

14 Stycznia 2025
Luxul

Luxul XMS-5248P Instrukcja

14 Stycznia 2025
Luxul

Luxul AMS-2624P Instrukcja

14 Stycznia 2025
Luxul

Luxul XGS-1005 Instrukcja

14 Stycznia 2025
Luxul

Luxul AGS-1008M Instrukcja

14 Stycznia 2025
Luxul

Luxul XMS-1208P Instrukcja

14 Stycznia 2025
Luxul

Luxul XMS-7048P Instrukcja

14 Stycznia 2025
Luxul

Luxul AMS-2600 Instrukcja

14 Stycznia 2025