Instrukcja obsługi JUNG IPR 200 REG

JUNG router IPR 200 REG

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla JUNG IPR 200 REG (16 stron) w kategorii router. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/16

Product Documentation

IP Router

Art. No.: IPR 200 REG

ALBRECHT JUNG GMBH & CO. KG

Volmestrasse 1

D-58579 Schalksmühle

GERMANY

Telephone: +49 2355 8060

Fax: +49 2355 806204

e-mail: kundencenter@jung.de

Internet: www.jung.de

1. Safety instructions

 Electrical equipment must only be installed and mounted by qualiﬁed

electricians.

 When connecting KNX interfaces, detailed knowledge through KNX training is

required.

• The manufacturer shall not be liable for any costs or damage incurred by the

user or third party through the use this device, misuse or disturbances of the

device or user equipment.

• Any unauthorized changes and modiﬁcations to the equipment will render the

warranty null and void!

• The manufacturer shall not be liable for damage arising from improper use.

2. Installation and connection

Operation of the KNXnet/IP router requires:

• One of the following power supplies with at least 1 Watt power output:

 Safety extra-low voltage of 20 to 30 VDC (direct voltage)

 Safety extra-low voltage of 16 to 24 VAC (alternating voltage)

 "Power over Ethernet" (IEEE 802.3af), Class 1

• A 10/100 Mbit compatible Ethernet connection

• A KNX/EIB bus connection

3. Commissioning

3.1 Description of functions

The interface has the following functionalities:

 LED display for communication, Ethernet communication and programming

mode

• Configuration via ETS

• Max. 5 connections to IP terminal devices, e.g. for simultaneous visualisation

and conﬁguration

• Supply from network line Power-over-Ethernet to IEEE 802.3af , through – –

separate voltage supply or the auxiliary voltage output of the KNX voltage

supply.

• Electrical isolation between KNX and IP network

3.2 Conﬁguration

In the ETS project, an appropriate device must be created and conﬁgured.

• Activate programming mode: Press programming button.

• The programming LED lights up.

• Program a physical address with the aid of the ETS.

• The programming LED goes out .

• Label the device with the physical address.

• Load application data into the device with the aid of the ETS.

3.3 Physical address of the data interface

A direct connection to the KNX can be established from a PC or other data

processing equipment (e.g. visualisation units) in the network via an IP data network

and the KNX IP interfaces. This allows access to the bus from any point in the IP

data network.

The ETS3 (from version 3.0c) enables the conﬁguration of KNX installations via the

existing IP data network and uses the IP interface such as a conventional serial

RS232 or USB data interfaces for communication with the bus. This also includes the

downloading of bus devices or the group bus monitor function (no support of the bus

monitor mode).

For communication via KNXnet/IP Tunnelling and / or ObjectServer, the device must

use a virtual physical address for each connection. These additional physical

addresses must not be identical with the physical address of the device and must not

be used by any other bus device either. In the ETS, the virtual physical addresses

should be allocated by dummy devices. The additional addresses for the KNXnet/IP

Tunnelling can either be assigned manually in the ETS by the communication

settings or automatically by the device itself. To conﬁgure the communication

interface (physical interface of the ﬁrst tunnel connection) in the ETS 5, the following

steps must be carried out.

In ETS 5, on the tab, open the subitem Bus Connections -> Interfaces

If the IP interface is online in the same network as the commissioning PC, this will

already be shown here, otherwise it can be created using the "New" button.

Specyfikacje produktu

Marka:	JUNG
Kategoria:	router
Model:	IPR 200 REG
Kolor produktu:	Biały
Rodzaj zasilania:	AC, DC, PoE
Certyfikaty:	CE
Standardy komunikacyjne:	IEEE 802.3af
Prędkość transferu danych przez Ethernet LAN:	10, 100 Mbit/s
Ilość portów Ethernet LAN (RJ-45):	1
Obsługa PoE:	Tak
Zarządzanie przez stronę www:	Tak
Przewodowa sieć LAN:	Tak
Pobór mocy:	1 W
Diody LED:	Tak
Firewall:	Nie
Ilość portów Fast Ethernet (PoE):	1