Instrukcja obsługi JUNG GCR1561.07F

JUNG nieskategoryzowany GCR1561.07F

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla JUNG GCR1561.07F (17 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/17
Radio Management Radio push button
Ref.-no.: ...1561.07 F...
Operating Instructions
Radio push button R2.1
1. Function
The pushbutton with radio-control receiver permits radio-controlled or
manual switching and dimming of lamps. The starting brightness can be
stored in the device as memory brightness. The pushbutton with radio-
control receiver is plugged onto one of the following inserts:
- Universal touch dimmer 1254 UDE
- Standard touch dimmer 1225 SDE
- Relay insert single-channel 1201 URE
- Relay insert two-channel 1202 URE
- Tronic switching insert 1254 TSE
- LV triac switching insert 1244 NVSE
- Touch control unit 1240 STE
After reception of a data telegram from a programmed radio-control
detector and corresponding darkness, the pushbutton with radiocontrol
receiver is switched on for about 1 minute with the preset memory
brightness. The pushbutton with radio-control receiver can be programmed
to identify up to 30 radio channels.
Lightscapes
The radio-control pushbutton can be included in up to five lightscapes
which are activated with the corresponding radio-control transmitters (e.g.
hand-held transmitter ‘Komfort’) and stored. The desired lightscape key
must be programmed beforehand into the radio-control pushbutton.
All-ON / All-OFF
The programming of a radio channel (e.g. hand-held transmitter ‘Komfort’)
always includes the simultaneous and automatic storage of the functions of
the All-ON or All-OFF key.The All-ON or All- OFF key of a radio-control
transmitter switches the load connected to the switching actuator on or off.
Light control
In combination with a programmed radio-control presence detector or light
sensor, the radio-control pushbutton can be used for lighting control
functions. For more information, refer to the operating instructions of the
radio presence detector or light sensor.
Stand: Mai-07 325 276 13
Radio Management Radio push button
Ref.-no.: ...1561.07 F...
Important
The present instructions describe the functions of the radio-control
pushbutton without lighting control. More information on light control with a
presence detector or a light sensor is set out in the operating instructions
for these devices.
2. Warning
Caution: The installation and assembly of electrical equipment may only be
performed by a skilled electrician.
3. Fitting
The radio-control pushbutton can only be operated in conjunction with the
inserts listed under ‘Functions’. Connection and fitting are described in the
operating instructions of the insert.
Procedure
1. Install the selected insert (1)in a flush-mounting box (deep model
recommended), the connecting terminals of the insert pointing downwards.
2. Plug the radio-control pushbutton (2)together with frame (3)onto the
insert while the mains voltage is disconnected.
Important
• The distance from electrical appliances (e.g. microwave oven, hi-fi
and TV sets) must be at least 0.5 m.
• To prevent saturation of the radio receiver (actuator), the
radiocontrol pushbutton must be at least 1 m away from the
nearest transmitter.
2
Radio Management Radio push button
Ref.-no.: ...1561.07 F...
4. Learning a Radio Transmitter
During programming of a transmitter, the sensitivity of a radiocontrol
receiver is reduced to a range of approx. 5 m. The distance between the
radio-control pushbutton and the transmitter to be programmed should be
between 0.5 m and 5 m.
Procedure
1. Switch o the load connected to the radio-control pushbutton by a brief
depression (< 0,4 s) of any of the two pushbutton rockers.
2. Depress both rockers of the radio-control pushbutton at the same time
for abt. 4 seconds (fig. B: double-sided operation) to switch over to the
programming mode. The programming mode is active for abt. 1 minute
and confirmed by an intermittent tone (fig. C).
3. Send a radio telegram from the selected transmitter (fig. D); see
„Radio-control transmitter“ operating instructions:
3

Specyfikacje produktu

Marka: JUNG
Kategoria: nieskategoryzowany
Model: GCR1561.07F

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z JUNG GCR1561.07F, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje nieskategoryzowany JUNG

JUNG

JUNG ES1565.07 Instrukcja

27 Września 2024
JUNG

JUNG LS539WWLEDLW-12 Instrukcja

27 Września 2024
JUNG

JUNG CD1561.07 Instrukcja

27 Września 2024
JUNG

JUNG A1751B Instrukcja

27 Września 2024
JUNG

JUNG GCR1561.07F Instrukcja

27 Września 2024
JUNG

JUNG LS5232T3LG Instrukcja

27 Września 2024
JUNG

JUNG A5232MSAL Instrukcja

27 Września 2024
JUNG

JUNG MALS1082 Instrukcja

27 Września 2024
JUNG

JUNG ME5232MS Instrukcja

27 Września 2024
JUNG

JUNG SL5232MS Instrukcja

27 Września 2024

Instrukcje nieskategoryzowany

Najnowsze instrukcje dla nieskategoryzowany

Meec Tools

Meec Tools 010-084 Instrukcja

6 Października 2024
Outwell

Outwell Scenic Road 250 Instrukcja

5 Października 2024
Impact

Impact Qualite QL-3560-LED Instrukcja

4 Października 2024
Impact

Impact QuikBalance Instrukcja

4 Października 2024
Impact

Impact CA-112 Instrukcja

4 Października 2024
Impact

Impact Forever Ready Cool FRC-24-LED Instrukcja

4 Października 2024
Impact

Impact LS-BHA Instrukcja

4 Października 2024
Impact

Impact LKB-5C Instrukcja

4 Października 2024
Impact

Impact Varipole Drop Ceiling Adapter Instrukcja

4 Października 2024
Impact

Impact RST-001 Instrukcja

4 Października 2024