Instrukcja obsługi JLab GO Air TONES

JLab Zatyczka do uszu GO Air TONES

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla JLab GO Air TONES (3 stron) w kategorii Zatyczka do uszu. Ta instrukcja była pomocna dla 9 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/3
We love that you are rocking JLab!
We take pride in our products and fully stand behind them.
GO AIR TONES
EARBUDS
YOUR WARRANTY
All warranty claims are subject to JLab authorization
and at our sole discretion. Retain your proof of
purchase to ensure warranty coverage.
CONTACT US
Reach out to us at support@jlab.com
or visit jlab.com/contact
Remove tab and close door.
ADDING NEW ADDITIONAL BLUETOOTH DEVICES: /
Turn OFF Bluetooth from any previously connected
device. Turn ON Bluetooth from new device.
Take earbuds out of the case.
Earbuds will automatically enter Bluetooth Pairing.
Select “JLab GO Air Tones” in device settings to connect.
BLUETOOTH PAIRING
1
One earbud blink blue/white will indicating
ready to pair to your device.
3
Red light on case indicates charge.
Remove earbuds from case.
2
Select “JLab GO Air Tones” in your device's
Bluetooth settings to connect.
Voice prompt “Bluetooth connected” followed by
blinking white lights will indicate you are connected.
4
Bluetooth
Settings
JLab GO Air Tones
REGISTER TODAY
jlab.com/register
Product updates How-to tips|
FAQs & more
L
I
M
I
T
E
D
T
W
O
Y
E
A
R
W
A
R
R
A
N
T
Y
S
U
P
P
O
R
T
T
E
A
M
#
T
E
A
M
J
L
A
B
Earbuds will power off when placed in the case
and start charging the earbuds.
Earbuds will auto power on and connect to
your device when removed.
LEFT RIGHT
VOLUME DOWN: Single tap
SIRI (iOS) or “OK GOOGLE”
(ANDROID): Double tap
TRACK BACK: Press & hold 1+ sec
VOLUME UP: Single tap
PLAY PAUSE: / Double tap
TRACK FORWARD: Press & hold 1+ sec
VOICE PROMPTS
“Hello”: Power ON
“Ready to Pair”: GO Air Tones is
ready to pair to Bluetooth device
“Bluetooth Connected”:
Earbud is connected to device
“Battery Full”: 100-75%
“Battery Medium”: 75-25%
“Low Battery”: Less than 25%
(When power decreases to 10%,
“Low Battery” will play one time)
“Goodbye”: Power OFF
BUTTON FUNCTIONS
Tap either the right or left earbud 3 times for different EQ settings (GO Air Tones will cycle 3 EQ settings).
CUSTOM EQ3 SOUND MODES
JLab SIGNATURE
JLab C3™ signature
sound with amplified
bass and vocals
BALANCED
Even sound with
no additional
enhancements
BASS BOOST
Amplified bass
and sub-bass
CH NARGI G EARBUDS
1 2
ANSWER CALL: Single tap
HANGUP: Double tap
REJECT INCOMING CALLS: Press & hold 1+ sec
EQ CHANGE: Triple tap
Blinks 4x Red
Case less than 25%
(charge case)
Solid Red
Case 100-25%
FITTING
Connect the GO Air Tones into a computer or USB 5V 1A (or less) output device.
CH NARGI G CASE
OR
Place the earbud in the
ear canal and slightly
rotate to adjust for best fit.
Try all ear tips for best
fit and proper seal.
CAUTIONS
• Avoid extreme heat, cold, and humidity.
• Avoid dropping or crushing the earbuds.
• Wax may build up in the earbud tips, lowering the sound quality.
Carefully remove the wax with a cotton swab or other small tool to improve the sound quality.
• If you experience discomfort or pain, try lowering the volume or discontinuing use temporarily.
• If you experience regular discomfort while using this product, discontinue use and consult your physician.
• We recommend you treat your earbuds as you would a nice pair of sunglasses and keep them in safe location when not in use.
• The left or right earbud can be used independently for music and phone
calls. Simply choose one and take out of the case to connect.
• Only ONE Bluetooth device can be connected at a time. Turn off
Bluetooth on unwanted devices and turn on Bluetooth on chosen device
to connect.
Fully dry off the earbuds before
putting in the charging case to
avoid any damage to the case.
The earbuds are sweat/water
resistant but the case is not.
QUICK TIPS
WARNING
Shop products Product alerts Burn-in your headphones| |
JLab Store + Burn-in Tool
JLAB.COM
Instructional videos at: JLAB.COM/MANUALS
TROUBLESHOOTING
Connection failure or earbuds disconnected from each other (Manual Reset)
1 Keep the earbuds in the charging case and forget “JLab GO Air Tones” from your Bluetooth device settings.
2 Quick tap 7x on one earbud in charging case. Earbud blinks blue 4 times.
3 Quick tap 7x on other earbud in charging case. Earbud blinks blue 4 times.
4 Take both earbuds out of the charging case.
One earbud will be solid white and other will blink blue/white indicating ready to pair to your device.
Charging
Blinks Blue
Fully Charged
Solid Blue

Specyfikacje produktu

Marka: JLab
Kategoria: Zatyczka do uszu
Model: GO Air TONES

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z JLab GO Air TONES, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Zatyczka do uszu JLab

JLab

JLab JBuds Pro Signature Instrukcja

7 Października 2024
JLab

JLab Go Air Instrukcja

18 Września 2024
JLab

JLab JBuds Frames Instrukcja

10 Września 2024
JLab

JLab JBuds Air Executive Instrukcja

29 Sierpnia 2024
JLab

JLab GO Air TONES Instrukcja

5 Lipca 2024

Instrukcje Zatyczka do uszu

Najnowsze instrukcje dla Zatyczka do uszu

SilverCrest

SilverCrest SKG 16 A1 Instrukcja

12 Października 2024
Maxell

Maxell Dual Driver Instrukcja

9 Października 2024
Soundcore

Soundcore Sleep A20 Instrukcja

9 Października 2024
SBS

SBS Mood Instrukcja

9 Października 2024
SBS

SBS Go Pods Instrukcja

9 Października 2024
Vorago

Vorago ESB-305 Instrukcja

9 Października 2024
Vorago

Vorago EP-104 Instrukcja

9 Października 2024
VXi

VXi Reveal Pro Office Instrukcja

9 Października 2024
VXi

VXi BlueParrott Reveal Instrukcja

9 Października 2024
VXi

VXi V200 Instrukcja

9 Października 2024