Instrukcja obsługi Jablotron JA-60V

Jablotron Bezpieczeństwo JA-60V

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Jablotron JA-60V (2 stron) w kategorii Bezpieczeństwo. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

JA-60V Wireless outdoor PIR detector 1 MEB 52101

JA-60V Wireless outdoor P.I.R. motion detector

The JA-60V is an outdoor intruder detector designed to detect human

body movement in a protected area. Used PIR detector produced by Optex

has two double-layered detection patterns (upper and lower) both have to

be activated to trigger the alarm. This reduces false alarms, particularly

those caused by temperature changes, light reflection or small animals.

A tamper triggers an alarm if there is any attempt to tamper with the

detector.

The built-in transmitter is fully compatible with all JA-6X control panels.

Specifications

Power 3 V - 2 x AAA battery 1.5V

Battery life time about 1 year

Working frequency 433.92 MHz

RF Power

10 mV

Working range max. 100 m (open area)

Specification of the Optex VX 402R detector

Detection method Passive infrared

Coverage 12 m / 90° ; 14 segments

Mounting height 0.8 – 1.2 m

Detection speed 0.3 – 1.5 ms-1

Battery saving timer 5 or 120 seconds

LED indicator only in the test mode

Environmental class IV (EN 50131-1)

Operating temperature -20°C to +50°C

Waterproof IP54

Humidity 95%

Dimension 198 x 80 x 108 mm

Security grade 2 (EN 50131-1)

Can be operated according to ERC/REC 70-03

Hereby, Jablotron Ltd., declares that this JA-60V is in

compliance with the essential requirements and other

relevant provisions of Directive 1999/5/EC.

Original of the conformity assessment can be found at the web page

www.jablotron.cz, section Technical support.

Contents of the set: detector JA-60V, pole mounting kit, screw kit, area

masking plates, 2 AAA batteries

Installation

Select the proper place for mounting the detector according to

following:

1. Install the detector perpendicular to the ground to make upper

detection area parallel to the ground

2. Installation height is 0.8 – 1.2 m

3. Mount the detector so that a majority of traffic flow is across the

detection pattern

4. Too much light such as strong sunlight directed exactly to the sensor

may cause unstable condition. It is highly recommended to avoid

such installation.

3.1.1. 3.

0.8

1.2 m

To open the detector:

1. Unscrew the lock screw and remove the top cover.

2. Unscrew the screws fastening the back box. Remove the back

box.

NOTE: never touch surface of the PIR sensor.

Fix the detector to desired place. Detector can be fixed directly on the

wall or by using supplied fix bracket on the pole (Ø 43 – 48 mm).

Optical Part

Cover

Lock Screw

Back Box

Pole Mounting

Bracket

Setting Switches

Enrollment of the detector to the receiver

The transmitter is placed below the optical part of the detector. Study

the installation manual of the receiver unit (control panel) first to learn how

enter the enrolling mode. When the receiver is switched to the enrolment

mode insert the two provided AAA batteries into the detector (polarity is

marked in the detector). The detector will generate an enrollment signal

after the batteries are installed.

INSTANT

DELAY

JA-60N transmitter

• Use DIP switch no. 1 to select the reaction of the system:

- instant (position ON)

- delay (position 1).

• Leave DIP switch no. 2 in position ON.

Adjustment

The upper detection area stays parallel to the ground. The lower area

moves as shown below depending on the position of the setting switch.

Detection length is therefore limited by the length of lower detection

area, since both upper and lower detection area have to be activated

at the same time to trigger the detector.

distance 0 - 12 m

distance 0 - 2 m

distance 0 - 5 m

distance 0 - 8 m

JA-60V Wireless outdoor PIR detector 2 MEB 52101

Detection length setting table:

Max. detection length

Position Standard See Note bellow

A 12 m 10.0 to 15.0 m

B 8 m 6.0 to 10.0 m

C 5 m 4.0 to 5.5 m

D 2 m 1.5 to 2.5m

NOTE: the maximum detection length may vary as above due to

environmental thermal condition.

Detection Area

Level A,B,C,D

No Detection

Tolerance

Active area angle is 90°. By holding the pyro-electric unit it can be turned

in to desired direction ( in 15° steps).

45 90

Area masking – by provided masking plates section of the detection area,

which is exposed to the reflection of the sunlight, car light etc. can be

masked.

Sensitivity of the PIR sensor can be set by “SENS” switch in three

steps:

L - low

M - middle

H - high

Other parameters can be set using a DIP switch:

LED indicator OFF LED indicator ON

120 s 5 s Battery saving timer

4x 2x Pulse count

LED indicator is to be used for testing of the PIR detector. During

normal operation period is recommended to switch it off to save the

battery.

Depending on the 120s/5s battery saving timer DIP switch the movement

sensor will be blocked for a period of 5 or 120 seconds after a movement is

detected to conserves battery energy.

Depending on the Pulse count DIP switch the detector (both upper &

lower detection area) must be triggered 2 or 4 times to transmit the

alarm signal.

Operation test

Turn the LED indicator on, set the “battery saving timer” to 5 seconds

and close the detector. Every 5 seconds any movement in the

detection area will be indicated by the LED indicator and the alarm

information will be sent to the control panel.

Operation

To increase batteries lifetime it is highly recommended to switch the

“battery saving timer” to 120 seconds and switch off the LED indicator

in normal operating mode. The movement sensor will be blocked for 5 or

120 seconds after a movement is detected. This means that if there is

constant movement in the detection area the detector will transmit

information about the movement only once every 5 or 120 seconds.

Battery testing and replacement

The detector automatically checks the condition of its batteries. If it is

necessary to replace the batteries, the detector will inform the control panel

about it. If a low battery is indicated the detector works as normal but,

batteries should be replaced as soon as possible (within a week).

Before replacing the batteries, the control panel must be switched into

mode, which allows detectors opening (User mode or Programming

mode).

Use only high quality alkaline AAA batteries for replacement.

Note: Dispose of batteries safely depending on the type of the batteries and

local regulation. Although this product does not contain any harmful materials

we suggest you to return the product to the dealer or directly to the producer

after usage.

Troubleshooting

Problem Probable cause Remedy

Lower detection area is

unnecessarily long Set the detection area

properly

Detector receives

reflection of the reflector,

sunlight, car light etc.

Remove the reflector,

mask the area exposed to

the reflection of light or

change position of the

detector

There is a heat source in

the area that can cause

fast temperature change

(stove, heater etc.)

Remove the source of

heat or change position of

the detector

Detector

makes false

alarms

There is any moving object

in the area (laundry on the

clothesline, plans etc.)

Remove the moving object

or change position of the

detector

Detection area is not set

properly Set the detection are

properly

Occasionally

no detection Sensitivity is set to low (L) Change sensitivity to

medium (M) or high (H)

Low battery Replace the battery

LED does not light Turn LED switch ON

Detector

fails to work LED indicator lights but no

reaction on the control

panel

The control panel is out of

range, check the battery,

try to replace detector or

control panel

198

108

Dimensions

Note: Although this product does not contain any harmful

materials we suggest you to return the product to the dealer

or directly to the producer after usage.

Internet: www.jablotron.cz

Tel.: 483 559 999

fax: 483 559 993

Pod Skalkou 3 3

466 01 Jablonec nad Nisou

123

Specyfikacje produktu

Marka:	Jablotron
Kategoria:	Bezpieczeństwo
Model:	JA-60V

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Jablotron JA-60V, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Bezpieczeństwo Jablotron

Jablotron EYE-02 Instrukcja

24 Września 2024

Jablotron JA-60G Instrukcja

23 Września 2024

Jablotron JA-60B Instrukcja

23 Września 2024

Jablotron JA-63E Instrukcja

23 Września 2024

Jablotron JA-80D Instrukcja

23 Września 2024

Jablotron JA-50S Instrukcja

23 Września 2024

Jablotron JA-63F Instrukcja

23 Września 2024

Jablotron GBS-200 Instrukcja

21 Września 2024

Jablotron JA-63F wireless keypad Instrukcja

18 Września 2024

Jablotron CA-322 Accent Instrukcja

18 Września 2024

Instrukcje Bezpieczeństwo

Najnowsze instrukcje dla Bezpieczeństwo

Aritech SHATTERPRO 3 Instrukcja

15 Stycznia 2025

Axis Camera Station S9001 Mk II Desktop Terminal Instrukcja

15 Stycznia 2025

Eminent EM6511 Instrukcja

15 Stycznia 2025

Ranex RX2567-Z Instrukcja

11 Stycznia 2025

Technaxx TX-106 Instrukcja

11 Stycznia 2025

NetworX NX-595E IP Communication Module Instrukcja

5 Października 2024

Geemarc SOS-PRO 295 Instrukcja

2 Października 2024

One2track Safety Angel Instrukcja

28 Września 2024

Sygonix SY-3851632 Instrukcja

28 Września 2024

Sygonix 1326052 Instrukcja

28 Września 2024