Instrukcja obsługi Jablotron JA-60F

Jablotron Bezpieczeństwo JA-60F

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Jablotron JA-60F (3 stron) w kategorii Bezpieczeństwo. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/3

Wireless keypad JA-60F 1/3 MFF51008

Wireless keypad JA-60F

The JA-60F is an optional wireless keypad for the JA-60 or JA-65 series

wireless control panel. It can operate the system in exactly the same way as

the built-in keypad on the control panel and as the hard wired bus system

keypad, JA-60E. The LED indicators, display and built-in buzzer indicate the

alarm system’s status.

Multiple keypads and RC-11 or RC-4x remote controllers can be used with a

control panel (max. 8 totally). The keypad has a built in tamper sensor and it

also checks the number of attempts to enter an access code (5 unsuccessful

attempts will trigger a tamper alarm).

The keypad makes regular auto testing and reports its conditions regularly to

the system for full supervision.

The JA-60F keypad can be used for control panel programming as well.

Being wireless, it can help an installer to monitor the system functions when

performing a “walk” test.

Installation

Select the desired keypad location close to the entrance.

The keypad needs

a good quality, two ways radio communication with the control panel.

Under optimal conditions (open area, no interference) the working range

is about 80 meters. Indoors the distance of the keypad from the control

panel should not exceed 20 meters.

Any radio communication obstructions

or interference can reduce working distance. Test the JA-60F function, before

you attach it to the desired location.

1. Open the keypad by pressing on the internal tab on the right side (using a

screwdriver)

2. Select the enrolling mode on the control panel (see the control panel

installation manual) and then connect batteries into the keypad

3. The keypad will automatically enroll to the system.

4. Exit the enrolling mode on the control panel and test the keypad function

from the desired location

5. Mount the rear housing to the place (the internal tab should be on the right

hand side)

6. Reattach the front panel by placing the left side to the rear part and then

push the right side against the wall (the tab will click)

Optional power supply by an adapter:

If you want the JA-60F keypad to indicate the system status permanently, it

should be powered by an external power adapter with the output voltage of 12

VDC (stabilized). We recommend use of model DE 01-12 (Jablotron) power

supply.

Connect the +12 V and GND adapter outlet to the keypad terminals first.

Then insert batteries in order to enroll the keypad to the control panel. After

enrollment, plug the adapter into the power socket. Batteries will backup the

keypad's power when the main power fails. Do not use rechargeable batteries!

Optional external antenna

External antenna AN-01A can be used in order to increase the working dis-

tance. The external antenna should be connected to the antenna connector in

the JA-60F. Whenever you use this antenna disconnect the jumper located

next to it. Follow the antenna’s manual instructions when installing the an-

tenna.

Operation

The keypad can operate and program the system exactly the same way as

the built-in keypad on the control panel.

Functions F1 through F0 can be used on the JA-60F as described in the

JA-60 control panel manual. Beside this, there are 4 extra keys, which have

the following functions (when pressed for 0.2 seconds or more):

Setting (Arming)

(equal to F1 entry)

Door opening

(equal to F3 entry)

Partial setting

(equal to F2 entry)

Panic (access under duress)

(equal to F7, before access

code entry)

Programming of the control panel is only possible with the installer code. It is

recommended to use the control panel's built in keypad, or the JA-60E wired

keypad for programming.

Backlight of the keys

and displays switches on after the JA-60F cover is

opened or any key is pressed. It goes off automatically if there is no other entry

within 10 seconds. This feature prolongs the lifetime of the batteries. If an

acoustic indication of the entrance delay has been selected in the control

panel, the JA-60F indicates it after being activated (e.g. opening the cover or

pressing any key on the JA-60F).

The meaning of symbols on the keypad LED indicators:

Alarm Power supply

Tamper Set (Armed)

Fault Battery

Wireless communication indication

If the JA-60F is powered by an adapter, all the indications will be shown

regardless of activation.

Testing of the system with a JA-60F keypad

When installing and testing the system you can use the JA-60F keypad as a

portable control panel terminal.

When the keypad is not attached (the tamper switch is open), The JA-60F

permanently copies the control panel’s indicators. This way, after switching the

control panel to the programming mode you can pass through the premises

with the keypad in hands and test all installed components, seeing an exact

copy of the control panel’s reactions.

Battery testing and replacement

The keypad checks the conditions of its batteries automatically. If it is

necessary to replace the batteries, the keypad will indicate this situation. If a

low battery is indicated, it should be replaced as soon as possible (in a week).

Before the batteries are replaced, the control panel must be put into a mode

which allows for the opening of the keypad (

ser or

rogramming mode).

Use only high quality alkaline AAA batteries for replacement. After the

correct installation of the new batteries, the keypad will sound for a short while.

Specifications

power supply 6 V – 4 AAA alkaline batteries (50 uA)

or 12 V DC / 100 mA power adaptor

battery life time typ. 1 year

working frequency 433,92 MHz

working range max. 80 m (open area, no interference)

enclosure IP40

complies with EN 50131-1 grade 2

environmental class II indoor general -10 to +40 °C

can be operated according to ERC REC 70-03

Contents of the set:

keypad JA-60F, adhesive labels, 2 plastic dowels, 2

screws, and 4 AAA batteries

Jablotron Ltd. hereby declares that the JA-60F is in compliance with the

essential requirements and other relevant provisions of Directive

1999/5/EC. The original of the conformity assessment can be found on

the web site www.jablotron.com, Technical Support section.

Note

: Dispose of batteries safely depending on battery type and local

regulations. Although this product does not contain any harmful materi-

als we suggest you return the product to the dealer or directly to the

manufacturer after use.

JA-60A Wireless siren 2 / 2 MDX51006

Jablotron s.r.o. tímto prohlašuje, že výrobek JA-80F je ve shodě se

základními požadavky a dalšími příslušnými ustanoveními směrnice

1999/5/ES (NV č. 426/2000Sb.).

Poznámka: Výrobek, ačkoliv neobsahuje žádné škodlivé materiály,

nevyhazujte do odpadků, ale předejte na sběrné místo elektronického

odpadu. Podrobnější informace na www.jablotron.cz sekce

Poradenství.

JA-60E Wire Operated Keypad 2 / 2 MFE51007

Specyfikacje produktu

Marka:	Jablotron
Kategoria:	Bezpieczeństwo
Model:	JA-60F

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Jablotron JA-60F, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Bezpieczeństwo Jablotron

Jablotron EYE-02 Instrukcja

24 Września 2024

Jablotron JA-60G Instrukcja

23 Września 2024

Jablotron JA-60B Instrukcja

23 Września 2024

Jablotron JA-63E Instrukcja

23 Września 2024

Jablotron JA-80D Instrukcja

23 Września 2024

Jablotron JA-50S Instrukcja

23 Września 2024

Jablotron JA-63F Instrukcja

23 Września 2024

Jablotron GBS-200 Instrukcja

21 Września 2024

Jablotron JA-63F wireless keypad Instrukcja

18 Września 2024

Jablotron CA-322 Accent Instrukcja

18 Września 2024

Instrukcje Bezpieczeństwo

Najnowsze instrukcje dla Bezpieczeństwo

Aritech SHATTERPRO 3 Instrukcja

15 Stycznia 2025

Axis Camera Station S9001 Mk II Desktop Terminal Instrukcja

15 Stycznia 2025

Eminent EM6511 Instrukcja

15 Stycznia 2025

Ranex RX2567-Z Instrukcja

11 Stycznia 2025

Technaxx TX-106 Instrukcja

11 Stycznia 2025

NetworX NX-595E IP Communication Module Instrukcja

5 Października 2024

Geemarc SOS-PRO 295 Instrukcja

2 Października 2024

One2track Safety Angel Instrukcja

28 Września 2024

Sygonix SY-3851632 Instrukcja

28 Września 2024

Sygonix 1326052 Instrukcja

28 Września 2024