Instrukcja obsługi Ikelite 200DL

Ikelite kamera 200DL

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Ikelite 200DL (35 stron) w kategorii kamera. Ta instrukcja była pomocna dla 13 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/35

Product Registration

Please register your product within 15 days of purchase. Our product

registration database is the quickest way for us to contact you in the

event of a product update.

To register, send a photo of the above registration label to us via

ikelite@ikelite.com along with your name, address, and phone

number.

200DL Underwater Housing for Sony Alpha a1,

a7S III

Product # 71476

Introduction

Thank you for your purchase of Ikelite products.

Our primary focus is to provide quality, professional grade products

for use in and under water. Our products are designed, manufactured,

and distributed from our sole facility in Indianapolis, USA where we

started in 1962.

We are available if you have any questions or want photo advice.

Send us an email 24 hours a day to ikelite@ikelite.com. We strive to

reply within 1 business day.

An electronic version of this instruction manual is available for

download via the product page on our website:

https://www.ikelite.com

In the Box

• Housing

• Camera Mount for Sony a1 # 95419

• Camera Mount for Sony a7S III # 95415 (installed)

• Main O-ring # 0132.59 (installed)

• Port O-ring # 0132.45 (installed)

• Zoom Gear Retainer # 0072.42 (installed)

• Port Hole Cover # 0200.92 (installed)

• Waterproof Bulkhead Cap # 9104.7 (installed)

• Base with Left-Hand Quick Release Handle (installed)

• Hardware Set for Base with Handle # 9523.23 (installed)

• Tool for Zoom Gear Retainer # 0945.06

• .050” Hex Key # 0945.11

• Silicone Lubricant 1cc tube

Important Notices

»This housing requires a compatible DL lens port for waterproof

operation (sold separately). The housing is not waterproof

without a DL lens port attached.

»A bulkhead cap or sync cord must be attached to the housing

bulkhead for waterproof operation. Never submerge the

housing in water without either a sync cord or bulkhead cap

attached.

»Do not pull the shutter trigger without a camera installed. You

may accidentally detach or damage the control spring.

»Never leave a housing in a rinse tank, even if it is the only

system in the tank. Accidental damage may occur when the

user walks away from a housing while it is in the rinse tank.

»Do not use alcohol, cleaning agents, spray lubricants, Rain-X,

or other solvents on the housing or lens port. Use of an

incompatible chemical compound can damage the plastic and

o-rings, and may result in leaking.

»If you will be using the system in strong surf it is

recommended to draw a vacuum on the housing using the

optional vacuum pump (sold separately).

Contents

Product Registration 1

Introduction 2

In the Box 2

Important Notices 3

Getting to Know Your Housing 6

Base with Quick Release Handle 9

Accessory Port 9

Top Accessory Mount 10

Vacuum Valve 10

Trigger Extensions 10

Setting Up Your Camera 11

Pre-Installation Checklist 11

Camera Settings 11

Exposure Settings 11

Back Button Focus 12

Power Save 12

Setting Up Your Housing 13

Removing the Port Hole Cover 13

Installing a Zoom or Focus Gear 14

Opening the Housing 15

Installing the Camera 16

Attaching the Hotshoe 17

Closing the Housing 17

Turning the Camera On/Off 18

Attaching a Lens Port 19

Installing the Lens and Port 20

Setting Up An External Strobe 22

About Sync Cords 22

Attaching a Sync Cord or TTL Converter 23

Getting in the Water 24

Final Check 24

Entering the Water 25

Shooting Underwater 25

Learning about Underwater Photography 26

Maintaining Your Housing 26

Post-Dive 26

Lens Port 27

Storage 27

Servicing Recommendations 28

Lubricating Controls 28

Lubricating Push Buttons 29

Lubricating Control Shafts 29

Troubleshooting 31

Spare Parts 33

Limited Warranty 34

Service and Repairs 34

Getting to Know Your Housing

Shutter

Bulkhead

with cap

Port hole cover

Front dial

Tray mounts

Vacuum valve

Lens

release

Zoom /

Focus

Zoom gear

retainer

ISO

SONY A1, A7S III / 200 FT

71476 MADE IN USA

AEL

DISP

Playback C4 / Delete

Viewnder

AEL

AF-ON

O-ring

ISO

AEL

DISP

Set

Left

Down

Up / DISP

Right / ISO

Rear dial

Joystick

Bulkhead

without cap

Top mount

Power

Port mount

recess

Port mount

Exposure

compensation

C2 (custom 2)

Mode

Lid snap hook

Lid snap

Front o-ring

Accessory

port

Movie

Drive mode

dial (a1)

Base with Quick Release Handle

The hard anodized aluminum base plate attaches to your housing with

the two 1/4” nylon washers and 1/4-20 x 3/8” screws.

It is recommended to remove your base with quick release handle and

thoroughly rinse the tray, housing, and hardware periodically.

A central 1/4-20 threaded hole allows attachment of the base plate to

a standard tripod.

The base features additional mounting locations for attachment to a

variety of Ikelite housings (hardware not included).

Accessory Port

This housing features one spare accessory port which may be used

for the attachment of optional accessories. This port accepts ttings

designed for an M16 threaded hole. Visit ikelite.com for an updated list

of compatible products.

»Do not remove or loosen the accessory port plug unless you

are installing a compatible accessory.

Tripod mount

Top Accessory Mount

The housing features a 1/4-20 threaded top mount. Ball and ex type

mounts are available for the attachment of a GoPro camera, focus

light, or other lightweight accessories.

Vacuum Valve

Your housing features a valve to check for leaks before entering the

water. Use of the vacuum valve requires a pump, sold separately.

Valve lock

Plug

»DO NOT remove vacuum valve plug unless you are plugging in

a vacuum pump.

»DO NOT submerge the housing without the plug installed. The

housing will not be waterproof without the plug installed.

Trigger Extensions

The shutter and AF/MF/AEL levers may be extended to be closer

to your hands when using the optional Right-Hand Quick Release

Handle # 4077.02. This requires the Trigger Extension # 4077.95 (one

per control).

Trigger extensions and right-hand quick release handle are sold

separately.

Setting Up Your Camera

Pre-Installation Checklist

1. Insert a fully charged camera battery.

2. Insert a properly formatted memory card.

3. Remove lens cap and any attached lanyard or neck strap.

Camera Settings

• Set to “Off.”Eye-Start AF

• Set to “Monitor.”FINDER/MONITOR

• Set Touch Operation to “Off.”

• Set to “Yes”. This allows adjustments Release button to use dial

that are normally made by holding a button and rotating a command

dial to be made instead by rotating the command dial after the

button is released. Refer to your camera’s instruction manual for

more information.

• Set Flash mode to “Fill ash” when using an external strobe.

“Rear-curtain sync” may be used with compatible TTL converters.

• Set to “Off” when using an external strobe.Red Eye Reduction

• Set to “Off” when using an external strobe. AF Illuminator

• Set to “Off” when using an external strobe.Silent Shooting Mode

Exposure Settings

Refer to the in the Photo School section of our website Cheat Sheets

for recommendations on exposure settings for a wide variety of

shooting situations:

https://www.ikelite.com/blogs/cheat-sheets

Back Button Focus

Back button focus takes some adjustment to get used to but can be

very valuable in a variety of shooting scenarios.

Use the camera’s custom settings menu to set Pre-AF to “Off.” Set

AF w/Shutter AEL button to “Off.” In the custom key settings, set to

“AF-ON,” which initiates autofocus. Set to “AF/MF Cntrl AF/MF button

Toggle.”

The AEL button is conveniently accessed by a thumb lever on the side

of the housing. Instead of half-pressing the shutter to obtain focus and

lock focus, press AEL.

For super macro photography, you can use this technique instead of a

manual focus gear. Press AEL to lock focus at the minimum focusing

distance of your lens. Then move slightly in or out until the subject is

in focus.

Other focus functions like Focus Mode and Focus Area may be

assigned to the custom buttons on the camera for easy access.

Power Save

The camera’s power save function allows you to extend battery life

signicantly and yet always be ready for the next shot.

Instead of turning the camera off and on to conserve energy, the

camera will automatically sleep when not active. To wake the camera,

simply press the shutter button to instantly return to full power.

Use the camera’s setup menu to set Pwr Save Start Time to 1-5

minutes depending on your average period of time between active

shooting intervals.

Remote Control Cntrl w/Smartphone and settings must be turned

off for this to work. You also have to make sure that you’re not in one

of the camera’s menus, or it will prevent the camera from going to

sleep.

Setting Up Your Housing

Removing the Port Hole Cover

1. Align the zoom gear retainer tool with the notches in the zoom

gear retainer.

Tool

Retainer

Port mount

Port hole

cover

2. Rotate the removal tool counter-clockwise until the retainer is free

from the lens port mount.

3. Remove the port hole cover from the housing.

Installing a Zoom or Focus Gear

1. Place the zoom or focus gear (sold separately) into the lens port

mount opening with the gear teeth toward the inside of the

housing.

Zoom or

focus gear

Retainer

2. Place the gear retainer into the opening around the gear.

3. Tighten the retainer by turning clockwise with the tool until snug.

Do not overtighten.

Opening the Housing

1. Push the lid snap lock forward and lift the curved end away from

the housing.

Lock

2. Lid snaps are designed to provide enough force to compress the

o-ring for a proper seal. Keep rm pressure against the lid snap

while lifting it away.

3. Repeat with remaining lid snaps.

4. Remove the housing back.

Installing the Camera

1. Remove any lanyard or neck strap which may be attached to the

camera.

2. Check to see whether the camera’s lens will t through the port

opening of the housing. If not, the lens will need to be removed

from the camera body and re-attached after the camera body is

installed in the housing.

3. Remove the camera mount from the housing. If using the Sony

a1, use Camera Mount # 95419 (packaged separately). If using

the Sony a7S III, use Camera Mount # 95415. Store the additional

camera mount in a clean, dry place.

4. Line the mount screw up with the camera’s tripod socket. Use a at

screwdriver to tighten the mount plate to the camera.

LENS

Mount screw

1/4-20 tripod

mount

Camera

tripod socket

5. Pull out on the housing control knobs to move the controls out of

the way.

6. Insert the mount plate into the slot on the inside bottom of the

housing. Push the camera all of the way forward until it stops.

7. Push housing control knobs in and check orientation with the

camera.

»The camera may be attached to a tripod using the 1/4-20

threaded mounting hole on the bottom of the mount plate.

Attaching the Hotshoe

1. Orient the hotshoe with the arrow on top pointing towards the front

of the camera.

2. Slide the housing hotshoe into camera’s hotshoe mount until it

stops.

»The hotshoe must be all the way forward in the camera mount

for proper ash operation.

Closing the Housing

1. Make sure the o-ring is clean and in its proper location on the back

of the housing. The rear housing o-ring does not require lubricant

to make a seal.

2. Place the back onto the housing front.

Housing

hotshoe

Camera

hotshoe

mount

Specyfikacje produktu

Marka:	Ikelite
Kategoria:	kamera
Model:	200DL

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Ikelite 200DL, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje kamera Ikelite

Ikelite 200DL Instrukcja

1 Października 2024

Instrukcje kamera

Najnowsze instrukcje dla kamera

Polaroid Now Generation 3 Instrukcja

9 Kwietnia 2025

Reolink NVC-D12M Instrukcja

9 Kwietnia 2025

Panasonic Lumix DC-TZ91 Instrukcja

3 Kwietnia 2025

Vemer EasyEye.NOW Instrukcja

2 Kwietnia 2025

Maginon WK-7 HD Instrukcja

1 Kwietnia 2025

Rollei HD-30 Instrukcja

29 Marca 2025

Rollei Security Cam 1080p Instrukcja

29 Marca 2025

Syrp Magic Carpet PRO Instrukcja

27 Marca 2025

Aida HD-NDI-X20 Instrukcja

27 Marca 2025

Hasselblad CFV II 50c Instrukcja

27 Marca 2025