Instrukcja obsługi Hobbywing XeRun XR10 Pro WP

Hobbywing Zabawki sterowane radiem XeRun XR10 Pro WP

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Hobbywing XeRun XR10 Pro WP (2 stron) w kategorii Zabawki sterowane radiem. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

1. Turn on the transmitter, ensure all parameters (D/R, Curve, ATL) on the throttle channel are at default (100%). For transmitter without

LCD, please turn the knob to the maximum, and the throttle “TRIM” to 0. Please also turn the corresponding knob to the neutral

position. This step can be skipped if the radio's settings are default.

2. Start by turning on the transmitter with the ESC turned off but connected to a battery. Holding the “ON/OFF” button, the RED LED on

the ESC starts to ﬂash (the motor beeps at the same time), and then release the ON/OFF button.

Note: Beeps from the motor may be low sometimes, and you can check the LED status instead.

You must calibrate throttle range when you begin to use a new ESC, the transmitter has been replaced,or the Throttle TRIM have been adjusted, otherwise the ESC cannot work correctly. We strongly

recommend users to use the “Fail Safe” function on the radio system and set (F/S) to “Output OFF” or “Neutral Position”.The throttle calibration steps are below:

3. Set the neutral point, the full throttle endpoint and the full brake endpoint.

• Leave transmitter at the neutral position, press the “ON/OFF” button, the GREEN LED ﬂashes 1 time and the motor beeps 1 time to accept the neutral position.

• Pull the throttle trigger to the full throttle position, press the “ON/OFF” button, the GREEN LED blinks 2 times and the motor beeps 2 times to accept the full throttle endpoint.

• Push the throttle trigger to the full brake position, press the “ON/OFF” button, the GREEN LED blinks 3 times and the motor beeps 3 times to accept the full brake endpoint.

4. The motor can be started 3 seconds after the ESC/Radio calibration is complete.

Press the ON/OFF button.

The Green LED ﬂashes

twice andmotor

emits “Beep-

Beep” tone.

Move the throttle trigger to the

full throttle

Press the ON/OFF button.

The Green LED ﬂashes three

times and motor emits

“Beep-Beep-Beep”

tone.

Move the throttle trigger to the

full brake

With the throttle trigger

in the neutral position

Press the ON/OFF button.

The Green LED ﬂashes

once and

motor emits

“Beep” tone.

AT T ENT IO N

This is an extremely powerful brushless motor system. For your safety and the safety of those around you, we strongly recommend removing the pinion gear attached to the motor before

performing calibration and programming functions with this system. It is also advisable to keep the wheels in the air when you turn on the ESC.

• 9 select-to-use proﬁles applicable to all 1/10 RC car racing.

• Excellent waterproof and dustproof performance, fearless of various weather conditions.

• Separate PRG/FAN port is able to power an external fan for maximize cooling performance or connect a LCD program box or OTA Programmer to the ESC.

• Variable frequency regulation of PWM & brake frequencies allows users to precisely regulate the driving & braking forces (of the motors).

• Softening function (HOBBYWING-initiated) for milder or wilder driving control and better driving efficiency.

• Multiple protections: low-voltage cutoff protection, ESC and motor thermal protection, and fail safe (throttle signal loss protection),reverse polarity protection (the external standard cappack will still be damaged

if battery reversal occurs).

• Data logging for recording the maximum ESC/motor temperature, motor RPM, and others in real time.

• Firmware upgrade via Hobbywing multifunction LCD program box or OTA Programmer (item sold separately).

• To avoid short circuits, ensure that all wires and connections are well insulated before connecting the ESC to related devices.

• Ensure all devices in the system are connected correctly to prevent any damage to the system.

• Read the manuals of all the items being used in the build.Ensure gearing,setup,and overall install is correct and reasonable.

• Please use a soldering iron with the power of at least 60W to solder all input / output wires and connectors.

• Do not hold the vehicle in the air and rev it up to full throttle, as rubber tires can “expand” to extreme size or even crack to cause serious injury.

• Stop usage if the casing of the ESC exceeds 90 / 194 as this may cause damage to both the ESC and motor. Hobbywing recommends setting the “ESC Thermal Protection” to 105 / 221 (this refers to the ℃ ℉ ℃ ℉

internal temperature of the ESC).

• The battery must be disconnected after use.There is a small draw even when the system is off,and will eventually fully drain the battery.This may cause damage to the ESC, and will NOT BE COVERED UNDER

WARRANTY.

This ESC provides proportional braking function; the braking effect is decided by the position of the throttle trigger. It sets the percentage of available braking power when full brake is applied. Large amount

will shorten the braking time but it may damage your pinion and spur.

3D. Brake Rate Control

It’s adjustable from 1 to 20 (step: 1), The larger the setting value, the greater the brake rate, that is, the faster the braking. A suitable rate can aid the driver to brake his vehicle correctly. Generally, you can set it

to a high value to have a quick brake response.

3E. Brake Frequency

The brake force will be larger if the frequency is low; you will get a smoother brake force when the value is higher.If set this item to "Customized", then the brake frequency can be adjusted to a variable value

at any 0-100% throttle input, Please choose the frequencies as per the actual test results of your vehicles.

3F. Brake Control

Option 1: Linear

Hobbywing has recommended using this mode under all circumstances. The braking effect is a bit weaker in this mode than in Traditional brake mode, but it’s easy to control and brings great control feel.

Option 2: Traditional

This is a traditional brake method, just like the previous escs, the brake force is stronger.

Option 3: Hybrid

The ESC switches the brake mode between Linear and Traditional as per the vehicle speed to prevent the slide (between tires and track) from affecting the braking effect.

Note: Please select the right mode for your vehicle as per the track condition, motor performance, and etc.

4A. Boost Timing

It is effective within the whole throttle range; it directly affects the car speed on straightaway and turns. The ESC adjusts the timing dynamically as per the RPM (when “Boost Timing Activation” set to “RPM”)

or throttle amount (when “Boost Timing Activation” set to “Auto”) in the operation. The Boost Timing is not constant but variable.

4B. Boost Timing Activation

Option 1: RPM

In RPM mode, the ESC adjusts the Boost Timing dynamically as per the motor speed (RPM). The actual Boost Timing is 0 when the RPM is lower than the Boost Start RPM. The Boost Timing changes as per the

RPM when the RPM change is between the Boost Start RPM and the Boost End RPM. For example, if the Boost Timing is set to 5 degrees and the Boost Start RPM is 10000, the Boost End RPM is 15000. The

Boost Timing corresponds to different RPM is shown below. When the RPM is higher than the Boost End RPM, the actual Boost Timing is the value you had previously set.

1A. Running Mode

Option 1: Forward with Brake

Racing mode. It has only forward and brake functions.

Option 2: Forward/ Reverse with Brake

This option is known to be the “training” mode with “Forward/ Reverse with Brake” functions. The vehicle only brakes on the first time you push the throttle trigger to the reverse/brake position.If the motor stops

when the throttle trigger return to the neutral position and then re-push the trigger to reverse position,the vehicle will reverse,if the motor does not completely stop,then your vehicle won’t reverse but still brake,you

need to return the throttle trigger to the neutral position and push it to reverse again.This method is for preventing vehicle from being accidentally reversed.

Option 3: Forward and Reverse

The motor will reverse immediately when the throttle trigger is pushed to reverse position.This mode is generally used in special vehicles.

1B. Max. Reverse Force

The reverse force of the value will determine its speed. For the safety of your vehicle, we recommend using a low amount.

1C. Cutoff Voltage

Sets the voltage at which the ESC lowers or removes power to the motor in order to either keep the battery at a safe minimum voltage (for LiPo batteries). The ESC monitors the battery voltage all the time, it will

immediately reduce the power to 50% (in 2 seconds) and cut off the output 40 seconds later when the voltage goes below the cutoff threshold. The RED LED will ﬂash a short, single ﬂash that repeats ( , , ) ☆ ☆ ☆

to indicate the low-voltage cutoff protection is activated. Please set the “Cutoff Voltage” to “Disabled” or customize this item if you are using NiMH batteries.

Option 1: Disabled

The ESC does not cut the power off due to low voltage. We do not recommend using this option when you use any LiPo battery as you will irreversibly damage the product. You need to select this option when you

are using a NiMH pack.

Option 2: Auto

The ESC calculates the corresponding cutoff voltage for the battery shall be 7.0V.

Option 3: Customized

The customized cutoff threshold is a voltage for the whole battery pack (adjustable from 3.0V to 7.4V).

1D. ESC Thermal Protection

The output from the ESC will be cut off with the value you have preset.

The GREEN LED ﬂashes ( , , ) when the ESC temperature reaches to the preset value. The output will not resume until the ESC temperature gets down. ☆☆☆

Warning! Please do not disable this function unless you’re in a competition. Otherwise the high temperature may damage your ESC and even your motor.

1E. Motor Thermal Protection

The GREEN LED ﬂashes ( , , ) when the motor temperature reaches to the preset value. The output will not resume until the motor temperature gets down. ☆☆ ☆☆ ☆☆

Warning! Please do not disable this function unless you’re in a competition. Otherwise the high temperature may damage your motor and even your ESC. For non-Hobbywing motor, the ESC ma

get this protection activated too early/late because of the different temperature sensor inside the motor. In this case, please disable this function and monitor the motor temperature manually.

1F. BEC Voltage

BEC voltage can be adjusted between 5.0-7.4V.Set a reasonable value according to the working voltage of the servo.

1G. Smart Fan:

This esc has a fan control function. If this item is set to "Disabled", the fan will continue to run after the ESC is powered on; If this item is set to "Enabled", The fan will start running after the internal temperature

the esc exceeds 50 /122 .℃℉

1H. Remote Off

Option 1: Enabled

Users can simply push and hold the brake trigger for 6 seconds. This option allows the user to turn off the ESC without pushing the ON/OFF button switch.

Option 2: Disabled

Users must turn off the ESC by pressing the ON/OFF switch button from the ESC.

1I. Motor Rotation/Direction

With the motor shaft faces you (the rear end of the motor is away from you), increase the throttle input, the motor (shaft) will rotate in the CCW/CW direction if the “Motor Rotation / Direction” set to “CCW/CW”.

Generally, the vehicle runs forward when the motor (shaft) rotates in the CCW direction. However, some vehicles only run forward when the motor rotates in the CW direction due to the different chassis design. In

that case, you only need to set the “Motor Rotation/Direction” to “CW).

1J. Phase-AC Swap

If the A/C wire of ESC connect to A/C wire of motor with crossed way (A wire of ESC connects to C wire of motor, C wire of ESC connects to A wire), set this item as Enable.

Warning! When #A/#B/#C wire of ESC connect to #A/#B/#C wire of motor correspondingly, do not Set to Enable. Otherwise it will damage the ESC and motor.

2A. Throttle Rate Control

This item is used to control the throttle response. The higher the throttle rate,the more aggressive the throttle will be applied. A suitable rate can help driver to control

the vehicle properly during the starting-up process. Generally, you can set it to a high value to have a quick throttle response if you are proﬁcient at throttle control.

2B. Throttle Curvature

This parameter is used to set the throttle curve.The larger the curvature setting,the more aggressive the throttle will be applied in the previous stage; the smaller the curvature setting,

the softer the throttle will be applied in the previous stage. As shown in the schematic diagram of the curve on the right.

2C. Neutral Range

As not all transmitters have the same stability at “neutral position”, please adjust this parameter as per your preference. You can adjust to a bigger value when this happens.

2D. Initial Throttle Force

It also called as minimum throttle force. You can set it according to wheel tire and traction. If the ground is slippery, please set a small throttle force. Some motors have strong cogging

effect with lower FDR ,if there is any cogging with very light throttle input,you can try to increase the initial throttle force.

2E. Coast

This function allows the motor to naturally and smoothly reduce rpm/speed,and the vehicle will not experience sudden deceleration during the throttle release process.The higher the value,the stronger the "coasting"

feeling.

What is COAST?

When a vehicle has a larger ﬁnal drive ratio, the tendency of having a “drag” feel is higher. The “COAST” technology is to allow the car to roll (coast) even when the ﬁnal drive ratio is high. The Coast function

brings better and smoother control feeling to racers. Some drivers will refer to this to the traditional brushed motors.

Note: The Coast setting will not work if the drag brake is not set to 0%.

2F. PWM Drive Frequency

The acceleration will be more aggressive at the initial stage when the drive frequency is low; a higher drive frequency is smoother but this will create more heat to the ESC.If set this item to "Customized", then the

PWM frequency can be adjusted to a variable value at any 0-100% throttle input, Please choose the frequencies as per the actual test results of your vehicles.

2G. Softening Value

It allows users to fine-tune the bottom end, change the driving feel, and maximize the driving efficiency at different track conditions. The higher the "Softening Value ", the softer the bottom end. In Modified

class, drivers often feel the power of the bottom end is too aggressive. Little throttle input usually brings too much power to the car and make it hard to control at the corners, this is HOBBYWING's solution to help

bottom end traction.

You can increase the motor mechanical timing accordingly after you set the softening value. Every time you increase the softening value by 5 degrees, you can increase the mechanical timing by 1 degree. Note:

For example, if you set the softening value to 20 degrees, then you can increase the mechanical timing by 4 degrees. Please note that you will never increase the mechanical timing by over 5 degrees.

2H. Softening Range

It's the range to which "Softening Value” starts and ends. If set to 30% then the softening range will be from 0 throttle to 30% throttle.

3A. Drag Brake

It is the braking power produced when releasing from full speed to neutral position. This is to simulate the slight braking effect of a neutral brushed motor while coasting. It’s not recommended for buggy and

monster truck.

(Attention! Drag brake will consume more power and heat will be increased, use it cautiously.)

3B. Drag Brake Rate

This parameter is used to control the speed of the drag-brake response. Setting a suitable value can improve the drag braking effect of the vehicle, thus, improving drivability to suit each users. The value can

be adjusted up to 20 levels. Increasing the value will result in a greater drag brake effect. The other "Auto" option is available as well to choose from. “Auto” will intelligently adjust the drag brake acceleration

according to the current speed. The faster the current speed, the smaller the drag brake rate, vice versa.

3C. Max. Brake Force

CAUT IO NS

Thank you for purchasing this HOBBYWING product! Please read this

declaration carefullybefore use, once you use the product,we will assume

that you have read and agreed with all the content.Brushless power systems

can be very dangerous and any improper use may cause personal injury and

damage to the product and related devices, so please strictly follow the

instruction during installation and use.Because we have no control over the

use,installation, or maintenance of this product, no liability may be assumed

for any damages or losses resulting from the use of the product. We do not

assume responsibility for any losses caused by unauthorized modifications to

our product. We have the right to modify our product design, appearance,

features and usage requirements without notification. We, HOBBYWING,

are only responsible for our product cost and nothing else as result of using

our product.Regarding the possible semantic different between two

different versions of declaration, for users in mainland China, please take

the Chinese version as standard; for users in other regions, please take the

English version as standard.

AT T ENT IO N

1. Motor Connetion

Sensored motor connection MUST connect A from the ESC to A on the motor, B to B, and C to C, with the sensor wire connected any variation of the motor to ESC connections may cause damage.

Note: If the motor direction is reversed, change the parameter item “Motor Rotation” to achieve the correct setting.

2. Receiver Connetion

The throttle control cable on the ESC has to be plugged into the throttle (TH) channel on the receiver. The throttle control cable has an output voltage of 5-7.4V to the receiver and steering servo, hence, no

separate battery can be connected to the receiver. Otherwise, your ESC may be damaged.If additional power is required, disconnect the red wire on the throttle plug from the ESC.

3. Battery Connetion

Proper polarity is essential. Please ensure positive (+) connects to positive (+), and negative (-) connects to negative (-) when plugging in the battery! When reverse polarity is applied to the ESC from the

battery, the external standard cappack will be damaged.

Note: Item 4C (Boost Start RPM) & item 4D (Boost End RPM) are not programmable if item 4B (Timing Activation) is set to “Auto”.

Short press the power button to turn on the ESC in the off state, and long press the power button to turn off the ESC.

Attention! To prevent accidental shutdown in racing, pressing the power button cannot shut down the esc while the motor is running,if there is an emergency, battery plugs can be pulled out to turn off the ESC.

Option 2: Auto

In Auto mode, the ESC adjusts the Boost Timing dynamically as per the throttle amount. Only at full throttle, the actual Boost Timing is the value you had previously set.

4C. Boost Start RPM

This item defines the RPM at which Boost Timing is activated. For example, when the Boost Start RPM is set to 5000, the ESC will activate the corresponding Boost Timing when the RPM goes above 5000.

The specific value is determined by the Boost Timing and the Boost End RPM you had previously set.

4D. Boost End RPM

This item defines the RPM at which Boost Timing (you specifically set) is applied. For example, when Boost Timing is set to 10 degrees and the Boost End RPM to 15000, the ESC will activate the Boost Timing

of 10 degrees when the RPM goes above 15000. The ESC will adjust the Boost Timing accordingly as per the actual RPM when the RPM goes below 15000.

5A. Turbo Timing

This item is adjustable from 0 degree to 64 degrees, the corresponding turbo timing (you set) will initiate at full throttle. It’s usually activated on long straightaway and makes the motor unleash its maximum potential.

5B. Turbo Delay

When “TURBO DELAY” is set to “INSTANT”, the Turbo Timing will be activated right after the throttle trigger is moved to the full throttle position. When other value(s) is applied, you will need to hold the

throttle trigger at the full throttle position (as you set) till the Turbo Timing initiates.

5C. Turbo Increase Rate

This item is used to define the “speed” at which Turbo Timing is released when the trigger condition is met. For example, “3 degs/0.1sec” refers to the Turbo Timing of 3 degrees that will be released in 0.1

second. Both the acceleration and heat is higher when the “Turbo increase rate” is of a larger value.

5D. Turbo Decrease Rate

After the Turbo Timing is activated and the trigger condition turns to not be met (i.e. vehicle slows down at the end of the straightaway and gets into a corner, full throttle turns to partial throttle, the trigger

condition for Turbo Timing turns to be not met), if you disable all the Turbo Timing in a moment, an obvious slow-down like braking will be felt and cause the control of vehicle to become bad. If the ESC can

disable the Turbo Timing at some “speed”, the slow-down will be linear and the control will be improved.

Warning！Boost Timing & Turbo Timing can effectively improve the motor efficiency; they are usually used in competitions. Please take some time to read this manual and then set these two items carefully,

monitor the ESC & motor temperatures when you have a trial run and then adjust the Timing and FDR accordingly as aggressive Timings and FDR may cause your ESC or motor to be burnt.

• The RED LED turns on solid and the GREEN LED dies out when the throttle trigger is in the throttle neutral zone. The RED LED will blink meet the Zero Timing competition rules. if the total value of Boost

Timing and Turbo timing is 0.

• The RED LED dies out and the GREEN LED blinks when your vehicle runs forward. The GREEN LED turns solid when pulling the throttle trigger to the full (100%) throttle endpoint.

• The RED LED dies out and the GREEN LED blinks when you brake your vehicle. The GREEN LED turns solid when pushing the throttle trigger to the full brake endpoint and setting the “maximum brake force”

to 100%.

• The RED LED dies out, the GREEN LED blinks when you reverse your vehicle. The GREEN LED turns solid when pushing the throttle trigger to the full brake endpoint and setting the “reverse force” to 100%.

3. When Some Protection is Activated

• The RED LED flashes a short, single flash and repeats “ , , ” indicating the low voltage cutoff protection is activated.☆☆☆

• The GREEN LED flashes a short, single flash and repeats “ , , ” indicating the ESC thermal protection is activated.☆ ☆ ☆

• The GREEN LED flashes a short, double flash and repeats “ , , ” indicating the motor thermal protection is activated.☆☆ ☆☆ ☆☆

• The RED & GREEN LEDS flash a short, single flash and repeats “ , , ” at the same time indicating the drive mode has been automatically switched to sensorless mode from senored mode because of ☆☆☆

abnormal sensor signal when pairing the ESC with a sensored motor.

RPM (Motor Speed)

Actual Boost Timing

<10000

0 Degree

10001-11000

1 Degree

11001-12000

2 Degrees

12001-13000

3 Degrees

13001-14000

4 Degrees

14001-15000

5 Degrees

>15000

5 Degrees

External Programming

Port for Connecting

Program Card or OTA

Programmer.

In order to make one firmware applicable to all different racing conditions, there are nine “easy-to-select” preset modes (as shown below). Users are able to change the settings of the modes provided (and

rename those modes) as per the control feel, track, and etc. For example, the name can be changed from “Modify” to “TITI2019_MOD_4.5” to indicate the race was ran with a 4.5T motor at 2019 TITC. This can

be saved for future reference as well.

Mode #

Modes/Profiles

Zero Timing

TC-Modify

Buggy-2WD-Modify

Bubby-4WD-Modify

Practice

OpenBL-13.5T

OpenBL-17.5T

SCT-4 Pole

Drift 2WD Carpet

Applications

All Stock racing requiring users to use Zero timing (/blinky) program on their ESCs.

Modify class of 1/10 touring car racing

Modify class of 1/10 2WD buggy racing

Modify class of 1/10 4WD buggy racing

(With Reverse function activated,) practice and sport

13.5T Open Stock class of 1/10 touring car racing

17.5T Open Stock class of 1/10 touring car racing

1/10 short course truck using 4 pole motor

1/10 drift 2WD car on Carpet

Preset Modes for Different Racing：

Note: The recommended T counts are only applicable with the standard 3650/540 size (3 slot 2 pole) motors when ESCs are in blinky mode.

USER MANUAL

XERUN XR10 Pro-WP

Brushless Electronic Speed Controller

SHENZHEN HOBBYWING TECHNOLOGY Co., LTD. · 101-402 Building 4, Yasen Chuangxin Hi-tech Industrial Park, 8 Chengxin Road, Baolong Industrial Town, Longgang District, Shenzhen, China. February 27, 2024

20240227 HW-SMA540DUL00

Cont./Peak Current

Motor Type

Applications

160A/1200A

Sensored / Sensorless Brushless Motors

1/10 Touring&Buggy racing, 1/10 Drift,F1,Rally

Motor Limit

Model XERUN XR10 Pro-WP

LiPo Cells

BEC Output

Cooling Fan

Size

Weight

Programming Port

2S LiPo (Only 2S)

5-7.4V Adjustable, Continuous Current of 5A (Switch-mode)

37.7x37.2x19.6mm (w/o Fan)

95.6g (w/ wires)

PRG/FAN Port

Touring Car 4.5T Buggy 5.5T：≥ ：≥

Parameter ValuesSection Item Programmable Items

Forward and ReverseForward/ Reverse with Brake

General SettingThrottle ControlBrake ControlTiming

1A Running Mode Forward with Brake

3.0-7.4V Adjustable (Step: 0.1V)Auto (3.5V/Cell)1C Cutoff Voltage Disabled

75%50%1B Max. Reverse Force 25% 100%

125 /257℃℉

105 /221℃ ℉1D ESC Thermal Protection Disabled

3%-10% Adjustable (Step: 1%)2C Neutral Range

1-15 Adjustable (Step: 1)2D Initial Throttle Force

HybridTraditional3F Brake Control Linear

Auto

4B Boost Timing Activation RPM

4K2K

2F PWM Drive Frequency 1K

1F BEC Voltage 5.0V-7.4V Adjustable (Step:0.1V)

2A Throttle Rate Control 1-30 Adjustable (Step: 1)

2E Coast 0%-15% Adjustable (Step: 1%)

2G Softening Value 0-30° Adjustable (Step: 1°)

3A Drag Brake Force 0%-100% Adjustable (Step: 1%)

3B Drag Brake Rate Auto 1-20 Adjustable (Step: 1)

3C Max. Brake Force 0%-150% Adjustable (Step: 1%)

4A Boost Timing 0-64° Adjustable (Step: 1°)

4C Boost Start RPM 500-35000RPM (Step: 500RPM)

5A Turbo Timing 0-64° Adjustable (Step: 1°)

4D Boost End RPM 3000-60000RPM (Step: 500RPM)

3D Brake Rate Control 1-20 Adjustable (Step: 1)

125 /257℃℉

105 /221℃ ℉1E Motor Thermal Protection Disabled

Enabled1G Smart Fan Disabled

EnabledRemote Off Disabled

CW1I Motor Rotation CCW

Enabled1J Phase-AC Swap Disabled

Customized2B Throttle Curvature -10~10 Adjustable (Step: 1)

8K 12K 16K 24K 32K Customized

2K1K3E Brake Frequency 0.5K 4K 8K 12K 16K

20%10%2H Softening Range 0% 25% 30% 35% 40% 45% 50% 55% 60% 65% 70% 75%

0.1s0.05s5B Turbo Delay Instant 0.15s 0.2s 0.25s 0.3s 0.35s 0.4s 0.45s 0.5s 0.6s 0.7s 0.8s 0.9s 1.0s

5C Turbo Increase Rate Instant

Instant

30deg/0.1s

1deg/0.1s 2deg/0.1s 3deg/0.1s 5deg/0.1s 8deg/0.1s 12deg/0.1s 16deg/0.1s 20deg/0.1s 25deg/0.1s

1deg/0.1s 2deg/0.1s 3deg/0.1s 5deg/0.1s 8deg/0.1s 12deg/0.1s 16deg/0.1s 20deg/0.1s 25deg/0.1s5D Turbo Decrease Rate

Customized

• Restore the default values with a multifunction LCD program box pro

After connecting the program box to the ESC, Click on Parameter Settings and select the Reset Parameters to restore the factory settings.【】【】

• Restore the default values with a OTA Programmer (& HW Link App)

After connecting the OTA Programmer to the ESC, open the HOBBYWING HW Link App on your smart phone, select “Parameters” followed by “Factory Reset” to reset the ESC.

1. Program your ESC with a multifunction LCD program box pro

Connect the interface marked with "- + " on the esc to the interface marked with "ESC" on the program box using a separate programming cable(a cable with JR plugs at both ends included in the program

box packaging), then connect the esc to the battery and turn it on. Click on Parameter Settings to set the esc.【】

2. Using the OTA Programmer for parameter settings

Insert the programming cable of the OTA Programmer into the programming interface of the esc, and use your phone to install the HW Link APP to set the esc.

3. Read the running data of esc

1) Click on the Data record on the homepage of the LCD box pro to read the five extreme values of the highest temperature of the esc, the highest temperature of 【】

the motor, the maximum current, the lowest voltage of the battery, and the highest rpm of the motor during the operation of the esc.

2) By using the OTA Bluetooth module, you can view the five extreme values recorded above, real-time data, and historical data (curve chart) under the Data Log【】

menu in the HW LINK App on your phone.

4. Upgrade of firmware for esc

1) Using the LCD box pro or OTA programmer, download and install the HW LINK App on your phone,click on the Firmware Update button on the APP 【】

homepage to upgrade the firmware of the esc.

2) Connect to the computer through the LCD box pro, download and install Hobbywing USB LINK software on the computer, and use this software to

upgrade the firmware for esc.

Trouble SolutionsPossible Causes

1. No power was supplied to the ESC;

2. The ESC switch was damaged.

The throttle cable of the esc is connected incorrectly

or the throttle is not at the neutral position.

The default/popular motor rotation direction does not match

your car frame.

1. The receiver was influenced by some foreign interference;

2. The ESC entered the LVC protection;

3. The ESC entered the thermal shutdown protection.

1. The throttle neutral position on your transmitter

was actually in the braking zone;

2. Set the “Running Mode” improperly;

3. The ESC was damaged.

1. The (ESC-to-motor) wiring order was incorrect

2. Some soldering between the motor and the ESC was not good;

3. The ESC was damaged (some MOSFETS were burnt).

Check if all ESC & battery connectors have been well soldered or

firmly connected.

1. Plug the throttle cable into the throttle channel (CH2) by referring to

relevant mark shown on your receiver.

2. Calibrate the esc and radio.

Adjust the parameter "Motor Rotation".

1. Check all devices and try to find out all possible causes, and check the

transmitter’s battery voltage;

2. The RED LED keeps flashing indicating the LVC protection is activated,

please replace your pack;

3. The GREEN LED keeps flashing indicating the thermal protection is

activated, please let your ESC cool down before using it again.

1. Recalibrate the throttle neutral position;

2. Set the “Running Mode” to “Fwd/Rev with Brk “;

3. Contact the distributor for repair or other customer service.

1. Check the wiring order;

2. Check all soldering points, please re-solder if necessary;

3. Contact the distributor for repair or other customer service.

1. Change another pack with great discharging capability;

2. Change a low-speed motor, or increase the FDR;

3. Set the Throttle Rate Control to a low level.

1. Check if the sensor cable is loose or poor contact issue exists;

2. Hall sensor inside the motor or the ESC is damaged.

After power on, the RED LED flashes

and the motor does not work.

The vehicle is going in the reversed direction

when the forward throttle is applied.

The ESC was unable to start the status LED, the

motor, after it was powered on.

The motor stuttered but couldn’t start.

The vehicle could run forward (and brake),

but could not reverse.

The motor got stuck or stopped when increasing

the throttle during the starting-up process.

The RED & GREEN LEDS on the ESC flashed rapidly

at the same time when the throttle trigger was at

the neutral position.

The motor suddenly stopped or significantly

reduced the output in operation.

1. Poor discharging capability of the pack;

2. The RPM of the motor was too high, or the FDR

was too low;

3. The Throttle Rate Control is set too high.

(When pairing with a sensored motor) the ESC

automatically switched to sensorless mode

when it detected incorrect signal from Hall sensor.

Diagram of Throttle Curvature

Output

Power

Throttle

Throttle Curvature 0＝

Throttle Curvature 0＞

Throttle Curvature 0＜

Release the

ON/OFF button

once the RED

LED flashes.

Hold the ON/OFF

button

Battery

Electronic Speed Controller

Receiver

Motor

Orange (C)

Blue (A)

Sensor port of motor

Sensor wire

Switch

Yellow (B)

Specyfikacje produktu

Marka:	Hobbywing
Kategoria:	Zabawki sterowane radiem
Model:	XeRun XR10 Pro WP

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Hobbywing XeRun XR10 Pro WP, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Zabawki sterowane radiem Hobbywing

Hobbywing XeRun XR10 Pro WP Instrukcja

9 Października 2024

Hobbywing XeRun XR10 Stock Spec G2 Instrukcja

9 Października 2024

Hobbywing XeRun XR10 Justock G3S Instrukcja

9 Października 2024

Hobbywing XeRun XR8 PRO G3 Instrukcja

9 Października 2024

Hobbywing XeRun XR10 Justock G3 Handout Instrukcja

9 Października 2024

Hobbywing XeRun XR8 Plus G2S Instrukcja

9 Października 2024

Hobbywing XeRun XR10 Pro 1S Heavy Duty Instrukcja

9 Października 2024

Hobbywing XeRun XR10 Stock Spec 1S Instrukcja

9 Października 2024

Hobbywing XeRun XR10 PRO 160A Instrukcja

9 Października 2024

Hobbywing Xerun V10 G3 Instrukcja

7 Października 2024

Instrukcje Zabawki sterowane radiem

Najnowsze instrukcje dla Zabawki sterowane radiem

Spektrum AR6600T Instrukcja

15 Października 2024

Amewi Hyper Go Instrukcja

9 Października 2024

Carson Drift Burner Instrukcja

9 Października 2024

Carson Micro X-Warrior 2.0 Instrukcja

9 Października 2024

Reely RaVage 4x4 V2 Instrukcja

8 Października 2024

Spektrum FC6350HX Instrukcja

8 Października 2024

Spektrum S250 Instrukcja

8 Października 2024

Spektrum S660 Instrukcja

8 Października 2024

Little Tikes Tire Twister Instrukcja

8 Października 2024

Spektrum SPMXC2060 Instrukcja

7 Października 2024