Instrukcja obsługi Hobbywing Xerun D10
Hobbywing
Zabawki sterowane radiem
Xerun D10
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Hobbywing Xerun D10 (1 stron) w kategorii Zabawki sterowane radiem. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/1

• Please connect all the devices carefully, you may not control the vehicle properly or encounter some unpredictable issues like damaged components if any poor connection exists.
• To avoid possible damage (result from overheat to the product, please control the soldering time within ) 5 seconds when soldering the motor wires (a soldering iron with the power of at least 60W is needed).
• Stop immediate usage once the casing of the motor exceeds 100 /212 as high temperature may damage the motor and cause the rotor to demagnetize. Hobbywing recommends activating the “Motor Thermal ℃ ℉
Protection” (of the ESC).
• Read through the manuals of all power devices and chassis and ensure the power configuration is rational before using this unit.
• Never apply full throttle if the pinion gear is not mounted on, because (under the no-load circumstances) high RPMs may get the motor
damaged.
03
INSTALLATION & CONNECTION
Please note the following points when mounting or connecting the motor.
• The M3 screws with the length (not longer than 7mm) are needed when mounting the motor onto your vehicle.
• Please pay attention to the relevant marks (on the ESC) when soldering/connecting those output wires to the motor and make sure that you will strictly follow the wiring order (between the ESC & the
motor) of “A-A, B-B, and C-C”.
• Please ensure the sensor cable is clean and undamaged when you’re using a sensored ESC. You need to pay attention to the two connectors on the cable when connecting the ESC to the motor.
• Re-check all the connections between the ESC & the motor and ensure that they are all correct before tur ning on the ESC.
CAUT IO NS
AT T ENT ION
USER MANUAL
02
SPECIFICATIONS
Thanks for purchasing Hobbywing XERUN D10 motor. This sensored brushless power system is very powerful, any improper
usage can be dangerous and may damage the product and related devices. Please take your time and read through the
following instructions before you start using the motor. We have the right to modify the product design, appearance,
features and usage requirements without notification. We, Hobbywing, are only responsible for our product cost and
nothing else are result of using our product.
20210720
Model
(Turns)
PN
KV
(No-load)
LiPos
Diameter / Length Shaft Diameter / Length Stock Rotor Weight
( )g
Poles
Φ7-12.2*24.1-BUT*-L1
Φ5-12.1*24.1-BES*-L3
Φ=35.7mm(1.41")
L=52.6mm(2.07")
Φ=3.175mm(0.125")
L=15.0mm(0.591")
30401134 (Black)
30401135 (Red)
30401136 (Purple)
30401137 (Black)
30401138 (Red)
30401139 (Purple)
2
2
2-3S
10.5T
13.5T
4600KV
2900KV
157g
165g
CAUTIONS
01
04
TIMING ADJUSTMENT
The D10 motors provide a wide range of adjustable mechanical timings, the following are the methods & principles you can follow when adjusting the timing.
• You can adjust the motor timing after unfastening the screw on the rear end plate. Please adjust the timing as needed according to the mark (/white lines) at the rear end of the motor and fasten the screw after
the adjustment. For obtaining the optimal performance, you can change the output range and characteristic of your power system through adjusting the motor timing.
• Increasing the timing can increase the motor speed (/RPM), while that also increases the motor temperature and reduces the efficiency. A high(er) timing usually requires a high(er) ratio.
• Please ensure your ESC is properly programmed before setting the motor timing. For detailed information about ESC programming, please refer to the user manual of the ESC.
• After the timing adjustment, please ensure that your motor will not get overheat after running a whole pack (i.e. LiPo). You can get the information about the motor temperature via a infra-red temperature gun. If
the temperature is too high, please let the motor cool down first and then test again. If the temperature is still too high, then please reduce the timing or increase the FDR (that is to replace the pinion gear with fewer
teeth or spur gear with more teeth.).
OPTIONS
07
PARTS LIST
06
The D10 motor contains the following parts:
Front End Plate x 1Pcs
Rotor x 1Pcs
Stator x 1Pcs
Sensor Module x 1Pcs
Long Screws (M2 x 43.5mm) x 3Pcs
05
The XERUN D10 Motor is very strong in construction but also easy to disassemble for maintenance.
We recommend checking the bearings and cleaning the motor periodically..
Please follow the steps (as shown below) to assemble the motor. When disassembling the motor, the sequences are reversed.
ASSEMBLY & DIS-ASSEMBLY
PNOptional Parts Part Name Description
30820430
30820429
30820431
30820428
Applications (/Motors)
10.5T, 13.5T
10.5T, 13.5T
10.5T, 13.5T
10.5T, 13.5T
XERUN-D10-Rotor-L1-7-12.2*24.1-BUT
XERUN-D10-Rotor-L2-7-12.5*24.1-BUS
XERUN-D10-Rotor-L3-5-12.1*24.1-BES
XERUN-D10-Rotor-L4-5-12.3*24.1-CET
Weak magnetism Stock rotor for 10.T,
Feeblish magnetism
Moderate magnetism Stock rotor for 13.T,
Strong magnetism
Rotors
Install the rear end plate Install the rotor
Fasten the rear end plate with those long screws
Finished product
Install the sensor module
Install the front end plate
1 2 3
4 5 6
Front end plate x1
Rotor x1
Stator x1
Sensor module p1-x1
Long screws x3
M2 x 43.5mm
Specyfikacje produktu
Marka: | Hobbywing |
Kategoria: | Zabawki sterowane radiem |
Model: | Xerun D10 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Hobbywing Xerun D10, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Zabawki sterowane radiem Hobbywing

29 Marca 2025

29 Marca 2025

28 Marca 2025

28 Marca 2025

27 Marca 2025

27 Marca 2025

27 Marca 2025

27 Marca 2025

27 Marca 2025

27 Marca 2025
Instrukcje Zabawki sterowane radiem
- Zabawki sterowane radiem Spektrum
- Zabawki sterowane radiem DJI
- Zabawki sterowane radiem Chicco
- Zabawki sterowane radiem Spin Master
- Zabawki sterowane radiem Revell
- Zabawki sterowane radiem Biltema
- Zabawki sterowane radiem Traxxas
- Zabawki sterowane radiem Absima
- Zabawki sterowane radiem Little Tikes
- Zabawki sterowane radiem Velleman
- Zabawki sterowane radiem Lenoxx
- Zabawki sterowane radiem Maverick
- Zabawki sterowane radiem Parrot
- Zabawki sterowane radiem Carrera
- Zabawki sterowane radiem Carson
- Zabawki sterowane radiem SkyRC
- Zabawki sterowane radiem Reely
- Zabawki sterowane radiem Amewi
- Zabawki sterowane radiem Futaba
- Zabawki sterowane radiem Overmax
- Zabawki sterowane radiem Proline
- Zabawki sterowane radiem ACME
- Zabawki sterowane radiem TacTic
- Zabawki sterowane radiem Conrad
- Zabawki sterowane radiem Tamiya
- Zabawki sterowane radiem ARRMA
- Zabawki sterowane radiem Graupner
- Zabawki sterowane radiem Blade
- Zabawki sterowane radiem ParkZone
- Zabawki sterowane radiem JETI
- Zabawki sterowane radiem Ninco
- Zabawki sterowane radiem Multiplex
- Zabawki sterowane radiem SAB
- Zabawki sterowane radiem Ripmax
- Zabawki sterowane radiem Robbe
- Zabawki sterowane radiem LRP
- Zabawki sterowane radiem Axial
- Zabawki sterowane radiem Hangar 9
- Zabawki sterowane radiem FMS
- Zabawki sterowane radiem E-flite
- Zabawki sterowane radiem Flyzone
- Zabawki sterowane radiem XciteRC
- Zabawki sterowane radiem FrSky
- Zabawki sterowane radiem WLtoys
- Zabawki sterowane radiem Force Engine
- Zabawki sterowane radiem Sharper Image
- Zabawki sterowane radiem Vaterra
- Zabawki sterowane radiem Jada
- Zabawki sterowane radiem HPI Racing
- Zabawki sterowane radiem Kyosho
- Zabawki sterowane radiem PowerBox Systems
- Zabawki sterowane radiem Losi
- Zabawki sterowane radiem Hobby Zone
- Zabawki sterowane radiem JR
- Zabawki sterowane radiem RC4WD
- Zabawki sterowane radiem DF-Models
- Zabawki sterowane radiem ROCHOBBY
Najnowsze instrukcje dla Zabawki sterowane radiem

30 Marca 2025

30 Marca 2025

30 Marca 2025

30 Marca 2025

30 Marca 2025

29 Marca 2025

29 Marca 2025

29 Marca 2025

29 Marca 2025

29 Marca 2025