Instrukcja obsługi Hobbywing UBEC 5A HV (3-10S)

Hobbywing Zabawki sterowane radiem UBEC 5A HV (3-10S)

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Hobbywing UBEC 5A HV (3-10S) (1 stron) w kategorii Zabawki sterowane radiem. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/1

User Manual of 5A HV－

－

－－UBEC HW-SM811DUL-20130412

- 1 -

5 Amps High Voltage Switch Mode UBEC

1. Why do you need a high voltage UBEC?

The 5A-HV-UBEC is a switch-mode DC-DC regulator supplied with a 3S to 10S Lipo battery pack

and outputs a consistent safe power for your receiver, gyro and servos. It is very suitable for big

electric RC models such as fixed-wing aircrafts and helicopters which use more than 4 cells lithium

battery.

Using this UBEC, the receiver can obtain the power supply directly from the main battery pack, so

the additional battery pack for receiver is unnecessary.

Compared with the linear mode UBEC, the overall efficiency of the switch-mode UBEC is much

higher, so it can extend the working time of the receiver battery pack, and because a switch mode

UBEC can significantly reduce the heat emission, it can avoid the loss of control caused by the

over-heat problem which is frequently happened with the linear mode UBEC.

2. Specification:

2.1. Output Voltage: 5V or 6V (Changeable with an jumper )

2.2. Continuous output current: 5 Amps

2.3. Burst output current: 7.5 Amps

2.4. Input: 8V-42V (3-10 cells lithium battery pack)

2.5. Quiescent current: 20mA

2.6. Size: 48mm*27mm*9mm (length*width*height)

2.7. Weight: 30g

3. Features:

3.1. Designed with an advanced switch mode DC-DC regulator IC, the max efficiency of the chip

is up to 92%.

3.2. The output current is very large, the continuous output current is up to 5 Amps, and the

burst output current is up to 7.5 Amps.

3.3. Output short-circuits protection function.

3.4. A metal shield covers almost all the electronic components, and a filter (ferrite ring) is

attached with the output wires to significantly reduce the electromagnetic interference.

3.5. Ultra-wide input voltage from 8V-42V.

3.6. Safe power on with the polarity protection function. If the input polarity is not correct, the

UBEC can’t work, but it will not be damaged. What you need to do is just swapping the

battery pack’s polarity.

3.7. Shows the working status with an indicator (LED), it lights when the output is in normal

range.

3.8. A switch to turn on or turn off the output.

3.9. Accessory: A step-down voltage regulator with 0.7V down (from 6.0V to 5.3V)

4. Wiring

5. About RF interference

Although we have tried our best to reduce the electromagnetic interference caused by switch model

UBEC, it may still cause some interference to the receiver. So please install the filter (ferrite ring) far

away from the UBEC’s main board, and DON’T stack the filter on the main board. Please put the

whole UBEC as far as possible away from the receiver.

6. How to Use the UBEC?

6.1. Change the output voltage

The output voltage is chosen by a jumper. Please look at the upper picture, there are 3 pins at the

right corner, the upper one is Pin1, the middle one is Pin2, and the bottom one is Pin3. If the switch

is located at Pin1 and Pin2, the output is 6V. If the switch is located at Pin2 and Pin3, the output is

5V.

6.2. Working status indicator (LED)

The LED shows the status of the UBEC. When it lights, it means the UBEC has the normal output. If

it couldn’t light, please check the battery connections.

6.3. Turn on or turn off the UBEC

Push the switch to the "ON" position to turn on the UBEC; Push the switch to the “OFF" position to

turn off the UBEC.

6.4. About the 0.7V step-down voltage regulator

This 0.7V regulator is used for servos cannot work with 6V (including Futaba servo 9241, 9251,

9253, 9254, 9255, 9256 and etc). It changes the voltage from 6V to 5.3V. When the UBEC output is

set to 6V, please connect the regulator between the receiver and the above servos.

If you are using a servo can work with 6V input, the 0.7V regulator is unnecessary.

5A UBEC

5A UBEC5A UBEC Switch

Input

Output

5V Jumper for output

voltage selection

Specyfikacje produktu

Marka:	Hobbywing
Kategoria:	Zabawki sterowane radiem
Model:	UBEC 5A HV (3-10S)

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Hobbywing UBEC 5A HV (3-10S), zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Zabawki sterowane radiem Hobbywing

Hobbywing XeRun XR10 Pro WP Instrukcja

9 Października 2024

Hobbywing XeRun XR10 Stock Spec G2 Instrukcja

9 Października 2024

Hobbywing XeRun XR10 Justock G3S Instrukcja

9 Października 2024

Hobbywing XeRun XR8 PRO G3 Instrukcja

9 Października 2024

Hobbywing XeRun XR10 Justock G3 Handout Instrukcja

9 Października 2024

Hobbywing XeRun XR8 Plus G2S Instrukcja

9 Października 2024

Hobbywing XeRun XR10 Pro 1S Heavy Duty Instrukcja

9 Października 2024

Hobbywing XeRun XR10 Stock Spec 1S Instrukcja

9 Października 2024

Hobbywing XeRun XR10 PRO 160A Instrukcja

9 Października 2024

Hobbywing Xerun V10 G3 Instrukcja

7 Października 2024

Instrukcje Zabawki sterowane radiem

Najnowsze instrukcje dla Zabawki sterowane radiem

Spektrum AR6600T Instrukcja

15 Października 2024

Amewi Hyper Go Instrukcja

9 Października 2024

Carson Drift Burner Instrukcja

9 Października 2024

Carson Micro X-Warrior 2.0 Instrukcja

9 Października 2024

Reely RaVage 4x4 V2 Instrukcja

8 Października 2024

Spektrum FC6350HX Instrukcja

8 Października 2024

Spektrum S250 Instrukcja

8 Października 2024

Spektrum S660 Instrukcja

8 Października 2024

Little Tikes Tire Twister Instrukcja

8 Października 2024

Spektrum SPMXC2060 Instrukcja

7 Października 2024