Instrukcja obsługi Hobart 403
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Hobart 403 (8 stron) w kategorii Maszynka do mielenia mięsa. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/8
701 S. RIDGE AVENUE
TROY, OHIO 45373
937 332-3000
www.hobartcorp.com
MODEL 403 TENDERIZER
ML-38763 403
FORM 37023 Rev A. (August 2024)
– 2 –
Installation, Operation and Care of
MODEL 403 TENDERIZER
SAVE THESE INSTRUCTIONS
GENERAL
The model 403 Tenderizer is designed to tenderize a variety of meat products. The tenderizer consists
of a set of roller units which contain knives that knit together and tenderize pieces of meat as they pass
through the blades. Optional Wide 3/8" or Narrow 3/16" Julienne Knife Lift-out units are available. They are
used to cut food products, such as meats and cheeses, into strips.
INSTALLATION
UNPACKING
Immediately after unpacking, check for possible shipping damage. If the tenderizer is found to be damaged,
save the packaging material and contact the carrier within 5 days of delivery.
Remove machine from the shipping carton and place in the operating location. Remove transparent guard
(4, Fig. 1), lift off motor housing (3, Fig. 1) and remove screw (1, Fig. 2) that plugs the vent hole (see label
taped to machine). Insert dip stick (taped to machine) in vent hole. Replace housing and guard.
A cord with plug is furnished as standard equipment.
Before making electrical connections, check the specications on the machine data plate to ensure they
agree with those of your electrical service.
This machine must be cleaned after installation and before being put into service. Refer to MAINTENANCE
for instructions.
© HOBART, 2024
Fig. 1
– 3 –
SAFETY
Safety devices incorporated in this machine MUST be in correct operating position anytime this machine
is in service. Both the transparent guard and the motor housing must be in place. The pilot light (2, Fig. 1)
will remain on when either the transparent guard or motor housing is removed and the switch is on. Motor
will start when the guard and housing have been replaced. DO NOT defeat any of the safety features.
OPERATION
Turn the switch (1, Fig. 1) to ON. The pilot light (2, Fig. 1) will illuminate indicating power is supplied to
the machine.
To tenderize meats, simply drop cuts into the top of transparent guard and receive them at the bottom.
Only boneless meats should be used. Choice or tender cuts should be run through several times at
different angles. Less tender cuts should be run through several more times at different angles to increase
tenderness. Pull out excess sinews to improve tenderness.
Various combinations of different meat types may be blended together. This is accomplished by running
the meat types through separately to tenderize, then together creating a rmly knit cut. Large slices should
be under 3/ " thick.4
MAINTENANCE
Unplug machine power cord before beginning any maintenance procedure.
Specyfikacje produktu
| Marka: | Hobart |
| Kategoria: | Maszynka do mielenia mięsa |
| Model: | 403 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Hobart 403, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Maszynka do mielenia mięsa Hobart
7 Marca 2025
Inne instrukcje Hobart
7 Marca 2025
7 Marca 2025
5 Marca 2025
4 Marca 2025
27 Lutego 2025
6 Października 2024
29 Września 2024
29 Września 2024
29 Września 2024
25 Września 2024