Instrukcja obsługi Hobart MG1532


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Hobart MG1532 (8 stron) w kategorii Konsola miksująca. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/8
701 S. R ID G E AVENUE
TROY, OHIO 45373
937 332-3000
www.hobartcorp.com FORM 34389 Rev. E (January 2024)
MG1532 & MG2032 MIXER-GRINDERS
MODEL
MG1532 ML-134099 7.5 hp Grind Motor + 1 hp Mix Motor
MG2032 ML-134104 7.5 hp Grind Motor + 1 hp Mix Motor
MG2032 ML-134105 7.5 hp Grind Motor + 1 hp Mix Motor w/ Side Feed
MG2032 ML-141244 7.5 hp Grind Motor + 1 hp Mix Motor w/ Side Feed
MIXER GRINDER-
– 2 –
© HOBART, 2024
MODEL MG2032 MIXER-GRINDER
MODEL MG1532 MIXER-GRINDER
– 3 –
Installation, Operation, and Care of
MG1532 & MG2032 Mixer-Grinders
SAVE THESE INSTRUCTIONS
GENERAL
The MG1532 & MG2032 Mixer-Grinders are designed to use a #32(42/46) size knife and plate (knives
and plates are available at extra cost but not included with grinder). Do not use a plate with hole size
smaller than 3/ ".32
The MG1532 & MG2032 Mixer-Grinder are equipped with a 7 1/ HP2 Grind Motor and a 1 HP Mix Motor.
On all models, the worm rotates at 216 RPM and the mix arm rotates at 23 RPM.
The inclined hopper permits lower, easier loading while the tilted worm provides a convenient output height.
Releasing the latch handle allows the hopper guard (lid) to open easily torsion springs counterbalance
the lid's weight.
The exclusive Hobart designed #46 Wedge cylinder grinding end speeds product from hopper to grinding
end by pulling pieces of meat through the large upper opening of the cylinder (Fig. 1).
The MG1532 & MG2032 Mixer-Grinders may be ordered
with any of the following options and/or accessories:
Pneumatic foot switch accessory (can be easily
added at any time).
The hopper side-feed inlet can be ordered (and factory
installed) for the right side of the MG2032 hopper only
to allow product from a companion rst cut grinder
to feed directly into the hopper. An adapter ring for
the rst-cut grinder is an available accessory.
The MG1532 hopper can hold up to 150 pounds of fresh
meat. The MG2032 hopper can hold up to 200 pounds of
fresh meat. The MG1532 & MG2032 Mixer-Grinders can
grind at a rate of 55 to 60 pounds of fresh boneless beef per minute, rst or second cut through a 1/ " 8
plate. Pork can be ground rst cut through a 3/4" breaker plate and second cut through a 3/16" plate at 60 to
65 pounds per minute. Up to 60 pounds of frozen meat per batch can be ground from ake or stick form
when tempered to 26°F or higher and rst grind is through a 3/ " or larger plate. 8
For best results, we recommend using equipment in a cold room and/or using cold product. This will help
reduce the fatting of meat at the grinder head and on the mixing arm and worm.
Fig. 1


Specyfikacje produktu

Marka: Hobart
Kategoria: Konsola miksująca
Model: MG1532

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Hobart MG1532, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Konsola miksująca Hobart

Hobart

Hobart MG1532 Instrukcja

27 Lutego 2025

Instrukcje Konsola miksująca

Najnowsze instrukcje dla Konsola miksująca