Instrukcja obsługi Hendi 820612
Hendi
maszyna do cięcia
820612
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Hendi 820612 (12 stron) w kategorii maszyna do cięcia. Ta instrukcja była pomocna dla 15 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/12
KNIFE SHARPENER
820612
You should read this user manual carefully before using the appliance.
Bevor Sie das Gerät in Betrieb nehmen, sollten Sie diese Gebrauchsanweisung aufmerksam lesen.
Alvorens de apparatuur in gebruik te nemen dient u deze gebruiksaanwijzing aandachtig te lezen.
Przed uruchomieniem urządzenia należy koniecznie dokładnie przeczytać niniejszą instrukcję obsługi.
Lisez attentivement ce mode d’emploi avant d’utiliser l’appareil .
Prima di utilizzare l’apparecchio in funzione leggere attentamente le istruzioni per l’uso.
Citiţi cu atenţie prezentul manual de utilizare înainte de folosirea aparatului.
Внимательно прочитайте руководство пользователя перед использованием прибора.
Πρέπει να διαβάσετε αυτές τις οδηγίες χρήσης προσεκτικά πριν χρησιμοποιήσετε τη συσκευή.
2
Keep these instructions with the appliance.
Diese Gebrauchsanweisung bitte beim Gerät aufbewahren.
Bewaar deze handleiding bij het apparaat.
Zachowaj instrukcję urządzenia
Gardez ces instructions avec cet appareil.
Conservate le istruzioni insieme all’apparecchio.
Păstraţi maualul de utilizare alături de aparat.
Хранить руководство вместе с устройством.
Φυλάξτε αυτές τις οδηγίες μαζί με τη συσκευή.
3
EN
Always place the sharpener on a flat and stable surface, firmly grip the handle
and make sure there is no possibility to cut yourself while sharpening. Don’t
use this sharpener for serrated blades or scissors.
Instructions:
This sharpener has three slots each engraved with a name: COARSE, FINE &
CERAMIC.
COARSE: for blunt stainless steel knifes.
Use this only if your knife is very blunt. Run the knife from its heel to its point
(never the other way around) through the slot engraved with ‘COARSE’ while ap-
plying slight pressure. Repeat this three times and continue with ‘FINE’ sharpen-
ing to remove any burrs that result from the re-edging and rough honing process.
This method brings back the edge to your knife and should only be done once
every six months or if the knife is really blunt.
FINE: for edge honing stainless steel knifes.
Run the knife from its heel to its point (never the other way around) through the
slot engraved with ‘FINE’ without pressure. Repeat this five times, rinse the knife
with running water and dry thoroughly.
This method can be used on it’s own to maintain a sharp blade. It’s recommended
to do this approximately once a week. The rods may discolour after use, this
is normal.
CERAMIC: for ceramic knifes only.
Lightly pull the knife from its heel to its point (never the other way around)
through the slot engraved with ‘CERAMIC’ without pressure. Repeat this three to
five times, rinse the knife with running water and dry thoroughly.
After use:
Do not put the sharpener in the dishwasher or submerge in in water. Store be-
yond the reach of children to avoid any accidents.
Specyfikacje produktu
Marka: | Hendi |
Kategoria: | maszyna do cięcia |
Model: | 820612 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Hendi 820612, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje maszyna do cięcia Hendi
24 Maja 2024
Instrukcje maszyna do cięcia
- maszyna do cięcia Severin
- maszyna do cięcia Concept
- maszyna do cięcia Cuisinart
- maszyna do cięcia Krups
- maszyna do cięcia Dremel
- maszyna do cięcia Graef
Najnowsze instrukcje dla maszyna do cięcia
14 Czerwca 2024
1 Czerwca 2024
21 Maja 2024
17 Maja 2024
15 Maja 2024
14 Maja 2024
8 Maja 2024
8 Maja 2024
6 Maja 2024