Instrukcja obsługi Harley Davidson J03893 (2005)
Harley Davidson
Silnik
J03893 (2005)
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Harley Davidson J03893 (2005) (2 stron) w kategorii Silnik. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/2
-J03893 REV. 2005-08-10
FLHTCUSE HEATED SEAT KIT
GENERAL
Kit Number
51718-06
Models
This kit fits 1997 and later FLHT/I (Electra Glide
® Standard),
FLHTC/I (Electra Glide Classic) and FLHTCUI (Ultra Classic®
Electra Glide), and 1998 and later FLTR/I (Road Glide®)
models.
Additional Parts Required
If another accessory is already using the accessory circuit
connector [4] (under the seat, see Figure 1), the Heated Seat
Kit will require a Switched Circuit Adapter Harness (Part No.
70264-94A), available separately from a Harley-Davidson
dealer.
Electrical Overload
It is possible to overload your motorcycle's charging
system by adding too many electrical accessories. If your
combined electrical accessories operating at any one time
consume more electrical current than your vehicle's
charging system can produce, the electrical consumption
can discharge the battery and cause vehicle electrical
system damage. See a Harley-Davidson dealer for advice
about the amount of current consumed by additional
electrical accessories, or for necessary wiring changes.
(00211b)
When installing any electrical accessory, be certain not
to exceed the maximum amperage rating of the fuse or
circuit breaker protecting the affected circuit being modi-
fied. Exceeding the maximum amperage can lead to elec-
trical failures, which could result in death or serious injury.
(00310a)
The Heated Seat requires up to additional current4.2 Amps
from the electrical system.
Kit Contents
Table 1. Kit Contents
Part NumberDescription (Quantity)
Not Sold SeparatelyHeated seat
51479-06Grab strap
INSTALLATION
1. For 2006 and later FLHT/I/C/CI/CUI, and ALL FLTR
models:
a. Follow the instructions in the Owner's Manual to
remove the left-side and right-side saddlebags
b. Remove the bolts and flat washers to remove the
passenger grab strap and saddlebag front mounting
brackets from the chrome frame tube covers.
c. Remove the passenger grab strap.
2. ALL models: Follow the instructions in the Owner's
Manual to remove the seat.
To prevent accidental vehicle start-up, which could cause
death or serious injury, disconnect negative (-) battery
cable before proceeding. (00048a)
3. Follow the instructions in the Owner's Manual to remove
the negative (-) battery cable from the battery.
4. See Figure 1. Identify and remove the plug from the
accessory circuit connector [4] in front of the battery.
is01034
Figure 1. Accessory Circuit Connector [4] (2004 and Later
Shown)
5. Locate the heated seat connector on the underside of the
heated seat.
-J03893 1 of 2
NOTE
If another accessory is already using the accessory circuit
connector [4], use a Switched Circuit Adapter Harness (Part
No. 70264-94A, available separately) as a "Y" adapter.
6. Mate the heated seat connector to the accessory circuit
connector [4].
7. Follow the instructions in the Owner's Manual to re-connect
the negative (-) battery cable.
8. Guide the wiring into the space beneath the seat so that
the wiring will not be crimped when the seat is installed.
9. Follow the instructions in the Owner's Manual to install the
seat.
After installing seat, pull upward on seat to be sure it is
locked in position. While riding, a loose seat can shift
causing loss of control, which could result in death or
serious injury. (00070b)
10. For 1997 through 2005 FLHT/I/C/CI/CUI models: Pro-
ceed to the OPERATION section.
For 2006 and later FLHT/I/C/CI/CUI, and ALL FLTR
models:
a. See Figure 2. Obtain the passenger grab strapnew
(1) from the kit, and the saddlebag front mounting
brackets (4), bolts (3) and flat washers (2) removed
earlier.
b. Install the saddlebag front mounting brackets and
grab strap as shown to the chrome frame tube covers.
Finger-tighten the bolts.
c. Follow the instructions in the Owner's Manual to re-
install the left-side and right-side saddlebags.
d. Tighten the mounting bolts to 60-96 (7-11 Nm)in-lbs
after seating the saddlebags.
2
3
1
4
is01041
1. Passenger grab strap
2. Original equipment flat washer
3. Original equipment hex head bolt
4. Forward saddlebag mounting bracket
Figure 2. Grab Strap and Saddlebag Front Mounting
Bracket
OPERATION
NOTE
The accessory switch is a rocker switch found on the inner
fairing switch panel.
1. With the ignition/key switch at IGNITION or ACCESS,
open the circuit to the heated seat by flipping the
accessory switch from OFF to ON.
2. Two switches on the side of the seat control the rider and
passenger heating areas independently. The forward
switch controls the rider area, and the rearward switch
controls the passenger area.
a. In the center position, the heat to that area of the seat
is OFF.
b. Pressing the lower part of the switch in toward the
seat turns the heat in that area ON at the LOW set-
ting.
c. Pressing the upper part of the switch in toward the
seat turns the heat in that area ON at the HIGH set-
ting.
NOTES
If the accessory switch is left ON and a seat heater rocker
switch is left in either the LOW or HIGH position when the
motorcycle is turned off, the seat will begin heating when the
ignition/ key switch is turned to the IGNITION or ACCESS
position.
A seat heater in operation while the motorcycle engine is
turned off or running below normal operating speed can
quickly discharge the vehicle battery, which could lead to
a subsequent failure to start, and could damage the elec-
trical system.
1
3
2
4
is01042
1. Rider section heat control switch
2. Passenger section heat control switch
3. Low heat position
4. High heat position
Figure 3. Seat Heating Control Switches
-J03893 2 of 2
Specyfikacje produktu
| Marka: | Harley Davidson |
| Kategoria: | Silnik |
| Model: | J03893 (2005) |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Harley Davidson J03893 (2005), zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Silnik Harley Davidson
29 Września 2024
22 Września 2024
17 Września 2024
6 Września 2024
5 Września 2024
4 Września 2024
1 Września 2024
1 Września 2024
29 Sierpnia 2024
Instrukcje Silnik
- Silnik Yamaha
- Silnik Triumph
- Silnik Kawasaki
- Silnik Honda
- Silnik Milwaukee
- Silnik KTM
- Silnik Ducati
- Silnik BMW
- Silnik GasGas
- Silnik Suzuki
- Silnik Husqvarna
- Silnik Aprilia
- Silnik Mercedes-Benz
- Silnik Danfoss
- Silnik Texas
- Silnik ELAC
- Silnik Kettler
- Silnik Mitsubishi
- Silnik Indian
- Silnik Reebok
- Silnik Juki
- Silnik Beta
- Silnik Bajaj
- Silnik Royal Enfield
- Silnik Sherco
- Silnik Hyosung
- Silnik Benelli
- Silnik Cagiva
- Silnik Mash
- Silnik Hero
- Silnik Victory
- Silnik Emco
- Silnik Moto Guzzi
- Silnik SMC
- Silnik Ridley
- Silnik Anova
- Silnik Zero
- Silnik MV Agusta
- Silnik BodyCraft
- Silnik Mahindra
- Silnik CRRCpro
Najnowsze instrukcje dla Silnik
4 Grudnia 2024
15 Października 2024
15 Października 2024
14 Października 2024
14 Października 2024
14 Października 2024
14 Października 2024
14 Października 2024
13 Października 2024
13 Października 2024