Instrukcja obsługi Harley Davidson J01521 (1999)
Harley Davidson
Silnik
J01521 (1999)
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Harley Davidson J01521 (1999) (12 stron) w kategorii Silnik. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/12
INSTRUCTIONS
-J01521 REV. 3-22-99
MOTORCYCLE SERVICE LIFT ADAPTER KIT FOR DYNA TC88 MODELS
General
This kit is designed for 1999 and later Dyna TC88 model
motorcycles to be used with Motorcycle Service Lift (P/N
94653-98) and Motorcycle Cleaning Stand (P/N 94652-98).
Before using your adapter kit, it is your responsibility to read
and follow these installation and operating instructions
Harley Davidson strongly recommends that the
following procedures be performed by 2 people. Failure
to follow instructions can result in death or serious
injury.
This kit consists of the following components:
Qty DESCRIPTION PART No.
3 Frame lift adapter not sold
1 Frame leveling
extrusion not sold
Installation
A Service Manual for your motorcycle is available at your
Harley-Davidson Dealer.
1. See Figure 1. Position the motorcycle on a straight and
level surface. While the bike rests on the Jiffy Stand,
straighten the front wheel and place the frame leveling
extrusion under the front tire to keep the tire straight.
2. Slide the motorcycle lift (fully lowered) under the bike
from the right side (opposite jiffy stand side) lining up
the frame rails with each of the perpendicular jacking
rails on the lift. When properly aligned, the left frame rail
will be approximately 1” from the lift end section (Figure
2) and lift base will be adjacent to the Jiffy Stand (Figure
3). This will allow bike to be centered when moved to an
upright position.
1WARNING
®
1 of 3
Kit Number 98965-99
i01478
Figure 1 Frame Level Extrusion
Figure 2.
Figure 3.
i01479
i01480
Frame leveling extrusion
Side of frame
approximately
1” from end of
lift rail
Bottom of
frame rail
Lift adjacent to
Jiffy Stand
Jiffy
Stand
extended
Forward
lift rail
Forward
lift rail
3. See Figure 4. Install one frame lift adapter to the right
front frame rail. When properly installed, frame lift
adapter should butt against frame/footpeg support as
shown.
4. Holding motorcycle securely, carefully lean the bike
slightly to the right and install one of the frame lift
adapters to the left front frame rail (Figure 5) and one
frame lift adapter to the left rear frame rail (Figure 6).
Note that rear frame lift adapter follows the frame rail at
an angle inward under the bike.
5. Recheck overall position of lift. Frame lift adapters
should be centered over lift rails. Release friction pad
latch as shown in Figure 7.
-J01521 2 of 3
Figure 4.
Figure 5.
i01481
Figure 7.
Frame rail adapter
should rest snugly
against
footpeg/frame
support
i01484
Figure 6.
Use brake to
help hold bike
securely
Install frame lift
adapter over front
section of rail
i01483
Install frame lift adapter over
rear section of frame rail
Friction pad
latch Friction pad
i01482
Frame lift adapter
6. With one person still holding the bike upright, raise the
lift rails slightly so that the frame lift adapters begin to
contact the lift rails, making sure the adapters are
“square” to the frame. Figure 8. illustrates the left side
frame lift adapters in the correct position during initial lift
contact.
7. With one person holding the bike securely, remove
frame leveling extrusion from under the front tire, tilt bike
to the left and slide frame leveling extrusion (“U” section
up) between the right rear frame and the lift rail as
shown in Figure 9.
RAISING LIFT
1. With one person holding the bike securely, slowly raise
lift until the motorcycle wheels are off the ground and lift
is in position for work. Make sure the bike is balanced on
the lift rails.
2 Install 4 Hog Ties™ (2 per side) according to procedures
provided in the Motorcycle Lift Instructions. Figure 10.
illustrates Hog Ties™ installed.
LOWERING LIFT
1. See Figure 11. With Jiffy Stand extended, slowly lower
lift until tires are on ground and a gap exists between the
frame lift adapters and the upper portion of the lift rails.
2. Remove Hog TiesTM according to procedures provided in
the Motorcycle Lift Instructions.
Make sure to remove all frame lift adapters prior to riding
the motorcycle. Failure to remove lift adapters can result
in loss of control resulting in death or serious injury.
Removal
1. Carefully lean the bike to the right and remove frame lift
adapters from the left frame rail.
2. Carefully lean the bike to the left and remove frame lift
adapter and frame leveling extrusion from right frame
rail.
3. Lower the motorcycle lift completely and rest the bike on
the Jiffy Stand. Lock the friction pad lever latch to allow
movement of the lift.
4. Pull out lift from under motorcycle.
1WARNING
i01485
Figure 8.
Figure 9.
i01486
Figure 11.
i01488
Figure 10.
i01487
3 of 3
-J01521
Left side frame lift
adapters correctly
installed
Frame leveling extrusion
on right (rear) side
installed correctly
Front Hog
Tie™
Rear
Hog Tie™
Front Rear
Specyfikacje produktu
| Marka: | Harley Davidson |
| Kategoria: | Silnik |
| Model: | J01521 (1999) |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Harley Davidson J01521 (1999), zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Silnik Harley Davidson
29 Września 2024
22 Września 2024
17 Września 2024
6 Września 2024
5 Września 2024
4 Września 2024
1 Września 2024
29 Sierpnia 2024
Instrukcje Silnik
- Silnik Yamaha
- Silnik Triumph
- Silnik Kawasaki
- Silnik Honda
- Silnik Milwaukee
- Silnik KTM
- Silnik Ducati
- Silnik BMW
- Silnik GasGas
- Silnik Suzuki
- Silnik Husqvarna
- Silnik Aprilia
- Silnik Mercedes-Benz
- Silnik Danfoss
- Silnik Texas
- Silnik ELAC
- Silnik Mitsubishi
- Silnik Indian
- Silnik Reebok
- Silnik Juki
- Silnik Beta
- Silnik Bajaj
- Silnik Royal Enfield
- Silnik Sherco
- Silnik Hyosung
- Silnik Benelli
- Silnik Cagiva
- Silnik Mash
- Silnik Hero
- Silnik Victory
- Silnik Emco
- Silnik Moto Guzzi
- Silnik SMC
- Silnik Ridley
- Silnik Anova
- Silnik Zero
- Silnik MV Agusta
- Silnik BodyCraft
- Silnik Mahindra
- Silnik CRRCpro
Najnowsze instrukcje dla Silnik
15 Października 2024
15 Października 2024
14 Października 2024
14 Października 2024
14 Października 2024
14 Października 2024
14 Października 2024
13 Października 2024
13 Października 2024
13 Października 2024