Instrukcja obsługi Golden Age Project PRE-73 DLX PREMIER

Golden Age Project odbiornik PRE-73 DLX PREMIER

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Golden Age Project PRE-73 DLX PREMIER (2 stron) w kategorii odbiornik. Ta instrukcja była pomocna dla 12 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

W W W . G O L D E N A G E P R E M I E R . C O M I

Vintage Style Preamplifier

PRE-73 DLX

PREMIER

INTRODUCTION

Congratulations on choosing the Golden Age Project PRE-73 DLX PREMIER microphone preampliﬁer!

The PRE-73 DLX PREMIER is a one-channel vintage style microphone-, line- and instrument preampliﬁer. The signal path uses only dis-

crete components like resistors, capacitors and transistors. The line and microphone input and the line output are transformer balanced,

using three different transformers, each one optimized for its purpose.

This is the way audio components were built before integrated circuits became available. The subjective sound quality delivered by

vintage equipment is often prefered over the one delivered by modern products, a situation that is even more obvious now when music is

recorded with clean sounding digital audio equipment.

The circuit used in the PRE-73 DLX PREMIER is similar to the preamp section in the classical 1073 module with a corresponding sound

character that is warm, punchy, sweet and musical. These classic characteristics have been heard on countless recordings through the

years and it is a versatile sound that works very well on most sound sources and in most genres. The essence of this sound is now avail-

able at a surprisingly low cost, making it available to nearly everyone.

FEATURES

- Vintage style electronics. No integrated circuits in the signal path.

- All soldered, connector-free internal design for the purest and most reliable signal path, the only connector used is for the gain switch,

- UK-made Carnhill mic input and line output transformers and highpass inductor. The line input uses a custom transformer and the

circuit board is prepared for the Carnhill tone. The output is balanced and fully ﬂoating and can drive a 600 ohm load up to about 28 dBu.

- Traditional 23-position 1073-style gain switch that is also used to select the mic or the line input jack.

- Combo XLR/TRS mic and line input jacks and separate output XLR and TRS jacks for ﬂexible connections.

- A Neutrik XLR/TRS combo jack with gold over nickel plated bronze contacts is used for the mic input.

- Maximum gain on the mic input is 80 dB, enough to handle passive ribbon mics with quiet sound sources.

- Switchable impedance on the mic input, 1200 or 300 ohms. Changing the load impedance will change the tone of many mics.

- Gain range on the line input: -20 to + 10 dB.

- An active instrument input for guitar and bass that passes the signal through the mic input transformer, with selectable input imped-

ance, hi-Z or 100 kohm, by an internal jumper.

- Switchable phantom power and absolute phase. Traditional gain switch plastic knob and metal knobs for the other controls.

- The phantom power can deliver up to 10 mA according to the speciﬁcation standard. The 6.8 kohm phantom power resistors are

matched to within 0.1% to maintain good common-mode rejection in the circuit.

- Selectable 1073-style inductor based highpass ﬁlter at 50, 80, 160 or 300 Hz with a slope of 18 dB / octave.

- Selectable two position AIR EQ with a boost of about 3 or 6 dB at around 30 kHz.

- Insert jack for inserting EQ´s and other units. The insert jack can be switched in/out from the front panel. An internal jumper can select

if the insert jack always has an output signal or not.

- The output level control makes it possible to make ﬁne gain adjustments and also to overload the main gain stage(s) for more character

and then lower the signal to a suitable level before the output stage.

- An output pad allows the user to add character by attenuating the output signal after the output transformer by -7, -14, -21 or -28 dB for

overdriving the output stage and the output transformer by adding gain and then lower the output signal to a suitable level with the pad.

- A simple but effective 4-step LED output level meter.

- Tantalum and polystyrene capacitors in the traditional positions. Neutrik XLR/TRS combo jack is used for the mic input.

- Switches on the back panel for 600 ohm output termination and ground lift.

- Relays are used to control internal switching for phantom power, mic low-Z, insert and DI for shorter circuit board signal paths. The

relays are controlled by front panel switches.

- Circuit board star grounding scheme.

- Power supply with separate regulators for the audio circuit and the relay and LED circuit.

- External power supply to avoid interaction with the audio circuits and transformers.

- A solid build quality that will last many years of normal use.

W W W . G O L D E N A G E P R E M I E R . C O M II

CIRCUIT DESCRIPTION

The signal ﬁrst enters an input transformer,

one for the mic input and a one for the line

input. The primary of the mic input trans-

former has two windings that are either con-

nected in series or in parallell which results

in an input impedance of either 1200 Ohms

or 300 Ohms for the microphone input.

The transformers are followed by two input

gain stages. For gains up to 50dB, only one

of them is being used. For gains above 50dB,

the second gain stage is inserted in the signal path. Both gain stages uses

only three transistors each.

The signal then goes to the insert relay, the highpass ﬁlter and the output

level potentiometer and from there on to the output stage. This stage again

only uses three transistors, the last one in the chain is a hefty 2N3055 power

transistor run in class-A mode, driving the output transformer that is followed

by the stepped output attenuator.

So, all in all, the complete signal chain only contains a maximum of nine

active elements. Compare that to the big number of transistors that are usu-

ally used in one single integrated circuit!

USING THE PRE-73 DLX PREMIER

Using a preampliﬁer is not rocket science. Here are some points though to

help you getting the maximum out of the PRE-73 DLX PREMIER:

- Connect the cable from the power adaptor to the 24V AC connector on the

back panel of the PRE-73 DLX PREMIER. Do position the adaptor away from

the preamp. Power on the unit with the POWER switch on the front panel.

- Connect your mic and/or line sources to the input XLR/TRS combo jacks on

the back panel. A mic and a line source can be connected at the same time,

- Switching between the mic and line input is simply done by setting the LINE/

MIC gain switch to one of the LINE or MIC positions.

- Connect a cable from the XLR or the TRS output jack to the next unit in the

signal chain. Both jacks are connected in parallel and carry the same signal.

The outputs can feed both balanced and unbalanced inputs.

- Engage +48V phantom power for any microphone that needs it. It is a good

procedure to always disengage the phantom power and wait for about 10

seconds before unplugging a microphone.

- When the LOW-Z switch is engaged, the input impedance of the mic input

drops from 1200 Ohms to 300 Ohms. This will change the tone of many micro-

phones and will give you one more soundshaping option. It will also increase

the signal level.

SOUND CHARACTER

If you want the smallest amount of coloration, always set the OUTPUT level

potentiometer at or close to maximum, the OUTPUT PAD to OFF and adjust the

output level with the stepped LINE/MIC gain switch.

If you want more character, you can do any, or both of the following:

1. Turn the OUTPUT level potentiometer counterclock-wise and increase gain

with the LINE/MIC switch. This will drive the input gain stage(s) harder and

provoke more character from them.

2. Engage the stepped output attenuator (OUTPUT PAD) and again increase

gain with the LINE/MIC switch. This will also drive the output stage and the

output transformer harder and add character.

Setting OUTPUT PAD at -14 dB is also useful if the input of the following unit

has the -10 dBu semi-professional operating level. The standard operating

level of the PRE-73 DLX is +4 dBu, the output level into a 600 ohm load will be

about 1,23V when the “0” VU LED is lit when OUTPUT PAD is OFF.

DI INPUT

Instruments can be connected to the active DI TRS input on the front panel.

The DI uses a FET-buffer and has an input impedance of about 1,5 Mohm.

Press the DI switch to engage this input. The DI input works in the MIC posi-

tions of the LINE/MIC switch. Mic and Line sources at the back can remain

connected. The output of the DI circuit is sent through the mic input trans-

former.

HIGHPASS FILTER

The PRE-73 DLX PREMIER has an inductor based highpass ﬁlter with a roll off

of 18 dB/octave. This is a very useful tool to remove excessive bass energy.

AIR EQ

Engage one of the two positions of the AIR EQ if you want to add some level in

the upper frequency range. The center of the boost is at around 30 kHz.

The center OFF-position of the switch disengages the boost.

PHASE SWITCH

The phase switch simply reverses the phase by reversing the wires from

the secondary winding of the output transformer. Reversing the phase of the

signal is useful on a number of occasions, one example is phase reversing

the lower mic of a snare drum to make it sum in phase with the upper mic.

INSERT JACK

There is an unbalanced insert jack located on the back panel where you can

insert equalizers and other external effect units. It has an operating level of

about -18 dBu to -10 dBu. Send is on “tip” and return on “ring”.

The insert is engaged by pressing the INS switch on the front panel.

600 OHM TERM SWITCH

The output transformer used in the PRE-73 DLX PREMIER is designed for

having an ideal load of about 600 ohm. The input impedance of most modern

units is 10 kohm or more. The PRE-73 DLX PREMIER has a 600 ohm output

termination switch located on the back panel. Engaging the switch terminates

the output transformer with a resistor to bring down the load to about 600

ohms when the PRE-73 DLX PREMIER is used with modern products that will

typically have an input impedance of about 10 kohm.

This switch should normally be engaged if you are connecting the PRE-73 DLX

PREMIER to a modern product.

PLEASE NOTE: the output pad is designed for a load of 600 ohms meaning you

must have the termination switched engaged when the output of PRE-73 DLX

PREMIER is connected to a modern unit with a high-impedance input.

GROUND LIFT

There is a ground lift switch on the back panel that lifts the internal ground

from the cabinet. If the unit is mounted in a rack together with other units and

you experience ground loop problems, try engaging it.

CUSTOMIZING THE PRE-73 DLX PREMIER

There are several functions in the PRE-73 DLX PREMIER that can be custom-

ized by the user. Remove the top panel of the box and follow the instructions

below.

1. To change the input impedance of the active DI input to 100 kohm

Locate the jumper “DILowZ” just behind the DI TRS jack. Relocate the jumper

so that it covers both pins.

2. To cut the output signal to the insert jack when insert is not activated

Locate jumper “INSERT OUT” just behind the middle of the LINE input XLR

and the INSERT TRS jack. Remove the jumper and attach it to just one of the

two pins.

GAIN SETTING

There is a lot of gain available in the PRE-73 DLX PREMIER. If you ever experi-

ence self oscillation, make sure that the OUTPUT level control is set at or close

to it´s maximum setting and reduce gain with the LINE/MIC switch. You can

also try to disengage the Air EQ if it is used.

Do not use the highest gain settings with the active DI input engaged, this is

not needed anyway.

CARNHILL UPGRADE

The circuit board of the PRE-73 DLX MKII is prepared for the Carnhill line input

transformer, The upgrade work can be made by the distributor in your area or

you can do it yourself if you have soldering experience.

The Carnhill part can be bought in our webshop at www.goldenagemusic.se.

WARRANTY

The PRE-73 DLX PREMIER is built to last. But as in any electronic device,

components can break down.

There is a 1,0A, slow blow fuse located inside the unit. If the unit dies, please

check this fuse. If it has blown, replace it with a new one. You can also try with

another 24V AC adaptor if you have one available.

If this doesn´t help, or if the unit has another problem, it will need repair and

you should then contact the reseller where you bought the unit.

The warranty period is decided by the distributor for your country. The dis-

tributor will support Golden Age Project resellers and end users with repairs

and spare parts.

REGISTRATION

You are welcome to register your unit at: www.goldenagepremier.com

---------------------------

I would like to thank you for chosing the PRE-73 DLX PREMIER!

I hope it will serve you well and that it will help you in making

many great sounding recordings.

Bo Medin

Handmade high end pro audio for

a lot less than you would expect!

Specyfikacje produktu

Marka:	Golden Age Project
Kategoria:	odbiornik
Model:	PRE-73 DLX PREMIER

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Golden Age Project PRE-73 DLX PREMIER, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje odbiornik Golden Age Project

Golden Age Project PRE-73 JR Instrukcja

15 Września 2024

Golden Age Project PRE-73 DLX Instrukcja

9 Sierpnia 2024

Golden Age Project PRE-73 DLX PREMIER Instrukcja

4 Lipca 2024

Instrukcje odbiornik

Najnowsze instrukcje dla odbiornik

Denon AVR-S900W Instrukcja

15 Października 2024

Pro-Ject Amp Box DS2 Instrukcja

15 Października 2024

AKG HP12U Instrukcja

15 Października 2024

Apart SBR160 Instrukcja

14 Października 2024

American Audio VLP 600 Instrukcja

14 Października 2024

Chord Anni Instrukcja

14 Października 2024

Sennheiser EM 9046 SU Instrukcja

14 Października 2024

Yamaha MusicCast RX-V481 Instrukcja

13 Października 2024

JL Audio VX600/6i Instrukcja

12 Października 2024

Pioneer SX-303RDS Instrukcja

10 Października 2024