Instrukcja obsługi GEV 16897

GEV Bewegingsdetector 16897

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla GEV 16897 (6 stron) w kategorii Bewegingsdetector. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/6
Max. 14 Ct./Min aus dem deutschen Festnetz.
Mobil max. 42 Ct./Min.
International calls may vary.
GEV GmbH
Heidehofweg 16
25499 Tangstedt
Germany
www.gev.de
service@gev.de
Hotline: +49 (0)180/59 58 555
www.gev.de
Typ: Einbau-Bewegungsmelder
ATHLET MINI 360° LBD 16897
BA01175800
16WOA31
16897
A B
2 3
C
ROT
BRAUN
BLAU
LOAD
~IN
N L
on on on on on on on on
NIGHT/
24 HOURS
SENS
TIME
1 2
16 mm
76
Subject to technical and design changes without prior notice.
DEGBFRITPL
How it works
The motion detector operates using passive infrared technology.
Via a PIR sensor, the detector notices any heat sources moving
within its field of detection and switches on automatically.
Static heat sources do not trigger it. The adjustable twilight
switch lets you choose whether you have the motion detector
working day and night or only when it is dark. The integrated
timer also lets you adjust how long the light stays on.
Safety information
To be fitted by qualified electricians only, observing all
standard national installation regulations.
No work to be carried out while live. The circuit trip
switch must therefore be switched o.
Check to make sure the connecting cable is not live!
All warranty claims will be null and void in the event of any
damage or loss caused by failure to observe these operating
instructions. We accept no liability for any consequential
losses or damage. We accept no liability for any personal injury
or material damage caused by improper use or by failure to
observe the safety advice.
In such cases all warranty claims will be null and void. For
reasons of safety and approval, no unauthorised conversion
and/or modification of the appliance is allowed.
Where to install
The motion detector is at its most eective when approached
diagonally. Motion detectors should therefore always be set up
so that they are not directly approached.
Installation
The Inset Mini Motion Detector LBD consists of two parts:
Fig. A1 Fig. A2an inset sensor a power section. Disconnect
the inset sensor plug from the power section. Make a 16 mm-
diameter hole in the area in which you wish to install the device
and push the inset sensor into it. After installing the inset
sensor, reconnect the plug to the power section. Mount the
power pack in place . (Fig. A)
Connect the mains connection cable as shown in the circuit
diagram . Switch the circuit trip switch back on. (Fig. B)
Range test
Set the dip switch to 5 sec. and the TIME night/24 hours dip
switch to „24 hours (dip switch position OFF)“. If the motion
detector is switched on via a separate switch, turn this on. A
self-test is then initiated lasting approx. 30 seconds. When the
device turns o, the range test will begin. The device will now
switch on for approx. 5 seconds in response to any movement,
regardless of the ambient lighting level. This time period is
initiated by any movement from the front. This range test is
designed to help you to determine the field of detection. Set
the Sens dip switch according to your requirements (dip switch
position o, high sensitivity). Once this has been adjusted
successfully you will be able to make further settings.
Settings (Fig. C)
TIME: Time setting for switch-on time 5 sec. – 8 min. The
switch-o delay time is selected by moving the dip switch to
the „ON“ position.
NIGHT/24HOURS: Twilight switch 10 , dip switch position Lux
ON: If the brightness of the ambient light is less than 10 , the Lux
connected consumer is switched on. Twilight switch 2000 Lux,
dip switch position OFF: If the brightness of the ambient light
is less than 2000 Lux, the connected consumer is switched on.
Recycling instructions
This device may not be disposed of with the unsorted
household waste. Owners of old devices are required by
law to dispose of this device professionally. Contact your
town council for further information.
Recessed-mounted motion detector
ATHLET MINI 360° LBD 16897
Technical data
Field of detection 360° with a beam angle of 120°
Range approx. 6 m
Time adjustment the time adjustment can be set via the dip switch: 5 sec., 30 sec., 1 min., 3 min., 5 min., 8 min.
Twilight switch can be configured via dip switch, approx. 10 Lux/approx. 2000 Lux
Mains connection 230 V ~, 50 Hz
Switching capacity max. 200 W LEDs, max. 200 W energy saving lamp, max. 800 W incandescent lamps
Power consumption approx. 0,5 W
Protection type IP 44 for the sensor, IP 20 for the power section
Protection class II
Troubleshooting – Practical tips
Problem Cause Remedy
Motion detector switches the
light on too late
• Movement from the front “ dip switch to O (dip switch • Set „Sens
down)
Motion detector fails to achieve
maximum range
• Motion detector is mounted too low
• Dierence in temperature between heat source
and surroundings is not big enough
• Mount higher
Motion detector switches
light
on constantly or
when not necessary
• Constant thermal movement:
There are areas within detection range that are not
supposed to be monitored, e.g. footpaths, roads,
trees etc. Unexpected changes in heat sources
caused by storms, rain or fans.
The influence of direct / indirect sunlight

Specyfikacje produktu

Marka: GEV
Kategoria: Bewegingsdetector
Model: 16897

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z GEV 16897, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Bewegingsdetector GEV

GEV

GEV 16897 Instrukcja

2 Października 2024
GEV

GEV 16910 Instrukcja

2 Października 2024
GEV

GEV 16934 Instrukcja

2 Października 2024

Instrukcje Bewegingsdetector

Najnowsze instrukcje dla Bewegingsdetector

Pepperl+Fuchs

Pepperl+Fuchs RMS-D Instrukcja

2 Października 2024
Megatron

Megatron MT68031 Instrukcja

27 Września 2024
Megatron

Megatron MT68033 Instrukcja

27 Września 2024
DESQ

DESQ 2008 Instrukcja

26 Września 2024
Pentatech

Pentatech AN05 Instrukcja

24 Września 2024
Pentatech

Pentatech AN03 Instrukcja

24 Września 2024
Satel

Satel APMD-250 Instrukcja

22 Września 2024
Pentatech

Pentatech CA300 Instrukcja

22 Września 2024
ORNO

ORNO OR-CR-261 Instrukcja

22 Września 2024
ORNO

ORNO OR-CR-250 Instrukcja

22 Września 2024