Instrukcja obsługi Genelec F One

Genelec subwoofer F One

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Genelec F One (13 stron) w kategorii subwoofer. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/13
Operating Manual
操作手册
F One
F One Active Subwoofer
General description
The Genelec F One is a very compact
active subwoofer designed to complement
Genelec G One or G Two active loudspeak-
ers. The F One extends the system’s bass
response down to 35 Hz and integrates
perfectly with the main loudspeakers in
any environment. The playback level for the
whole system is conveniently controlled by
the wireless volume control provided with
the subwoofer. A wired volume control is
available as an option.
The F One has integrated bass manage-
ment for the two output channels which
directs frequencies below 85 Hz to the
subwoofer and higher frequencies through
the output connectors to the main loud-
speakers. When using the subwoofer for the
.1/LFE channel of a multichannel system, we
recommend that bass management is done
in the processor or receiver and only the LFE
channel is connected to the subwoofer.
Installation
Before connecting the audio signals, ensure
that all equipment is switched off.
As the F One contains its own amplier, no
separate power amplier is needed. Never
connect the F One to the loudspeaker out-
puts of a power amplier, integrated ampli-
er or receiver.
Please follow the steps listed below for a
succesful setting up of the subwoofer:
1. Check the contents of the shipment.
in addition to the subwoofer, there is a
wireless remote control, a mains cable,
an IR extension cable and a Quick Setup
Guide.
2. Pull out the battery insulating strip from
the underside of the remote control as
shown in gure 1. This strip insulates the
battery from the contacts on the remote
control during shipping and the remote
control does not function before it is
removed.
3. Place the subwoofer in its position.
4. Connect audio cables from your signal
source(s). You can connect up to two
digital audio sources and two analog
audio sources.
5. Connect the main loudspeakers to the
output connectors of the subwoofer.
6. Adjust the phase of the subwoofer as
instructed in this manual and the Quick
Setup Guide.
7. Use test recordings and familiar music
pieces to judge the sound balance. Use
the “SUBWOOFER LEVEL” rotary control
and the “BASS ROLL-OFF” dip switches
to ne-tune the balance. If this fails,
consider relocating the subwoofer.
Operating Environment
The F One subwoofer is designed for
indoor use only. The ambient temperature
should be 15-35 °C (50-95 °F) and the rela-
tive humidity 20-80 %. Condensation is not
allowed. If it has been stored or transported
in a cool environment, the product must be
allowed to warm up in its packing to the
ambient temperature before connecting
mains power.
Connectors
The F One is equipped with both analog
and digital signal input connectors, that
can be used simultaneously to connect
up to four audio sources (two analog, two
digital). Switching between sources is done
with the Select button on the connector
panel or with the “<” and “>” buttons on
the remote control. The colour of the LED
light on the subwoofer enclosure indicates
which source is selected.
Analog Input Connectors
The F One has two stereo inputs (3.5 mm
jack and L/R RCA connectors) and an LFE
RCA connector. The stereo inputs are par-
allel, so you can connect two audio sources
at the same time, just play only one of them
at a time. The Select function does not
work between these two inputs. The LFE
input is used for the LFE (.1) signal in a
2.1 or 5.1 channel sound system. The LFE
input has a 120 Hz low pass lter, so it is
not suitable for full frequency range signals.
Digital Input Connectors
The F One has two digital signal input con-
nectors, one coaxial and one optical, that
accept stereo PCM format digital signal. You
can connect two digital sources and switch
between them using the Select function.
Figure 1. Removing the battery insulating strip
from the remote control
Figure 2. Connectors and controls of the F One.
Figure 3. Audio cabling
2 dB
ROLL OFF PHASE
0/ 180°
0/ 90°
4 dB
F One Active Subwoofer
SELECT
L
OUT
RR
IN
L
STEREO
LFE
COAXIAL
OPTICAL
DIGI LTA
AUDIO IN
IR IN
LED OFF
ISS SENSITIVITY LOWISS
HT MODE
292 F1BT 6
www.genelec.com MADE IN FINLAND
SYSTEM
VOLUME
CONTROL
MAX
MIN
SUBW LEVEL
ON
OFF
SYSTEM VOLUME
CONTROL CONNECTOR
SUBWOOFER LEVEL
ROTARY ADJUSTMENT
DIP SWITCH GROUP:
ROLL OFF
PHASE
ANALOG AUDIO INPUTS:
RCA L AND R
3.5 MM STEREO JACK
LFE
DIP SWITCH GROUP:
HT MODE
ISS SENSITIVITY LOW
ISS
LED OFF
RCA L AND R
AUDIO OUTPUT
CONNECTORS
DIGITAL AUDIO INPUTS:
RCA COAXIAL
TOSLINK OPTICAL
MAINS INPUT
POWER BUTTON
IR IN CONNECTOR
SELECT BUTTON
DIGITAL SIGNAL SOURCES:
TV, STREAMER, SOUND CARD ETC.
ANALOG SIGNAL SOURCES:
PHONE, COMPUTER, RECEIVER ETC.AV
Tuner87 . H z5 M
GIZMO
2 dB
ROLL OFF PHASE
0/ 180°
0/ 90°
4 dB
L
OUT
R R
IN
L
STEREO
LFE
COAXIAL
OPTICAL
DIGI LTA
AUDIO IN
IR IN
SYSTEM
VOLUME
CONTROL
LED OFF
ISS SENSITIVITY LOWISS
HT MODE
292 F1BT 6
MAX
MIN
SUBW LEVEL
ON
OFF
F One Active Subwoofer
www.genelec.com MADE IN FINLAND

Specyfikacje produktu

Marka: Genelec
Kategoria: subwoofer
Model: F One

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Genelec F One, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje subwoofer Genelec

Genelec

Genelec 7040A Instrukcja

20 Sierpnia 2024
Genelec

Genelec F One Instrukcja

14 Sierpnia 2024

Instrukcje subwoofer

Najnowsze instrukcje dla subwoofer

JL Audio

JL Audio SGR-10TW3 Instrukcja

13 Października 2024
Teufel

Teufel T6 Instrukcja

13 Października 2024
Polk

Polk DB1040 Instrukcja

10 Października 2024
OSD Audio

OSD Audio NERO DUAL X8 Instrukcja

9 Października 2024
OSD Audio

OSD Audio NERO WSA Instrukcja

9 Października 2024
Kicker

Kicker 51CWQ102 Instrukcja

9 Października 2024
Kicker

Kicker 51CWQ122 Instrukcja

9 Października 2024
Kicker

Kicker 43C84 Instrukcja

9 Października 2024
Kicker

Kicker 51CWQ124 Instrukcja

9 Października 2024
OSD Audio

OSD Audio FS12 Instrukcja

9 Października 2024