Instrukcja obsługi Garmin gWind
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Garmin gWind (60 stron) w kategorii Morski. Ta instrukcja była pomocna dla 10 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/60
gWind™ Wireless
Installation Instructions......................................................... 2
Instructions d'installation....................................................... 6
Istruzioni di installazione..................................................... 10
Installationsanweisungen....................................................14
Instrucciones de instalación................................................18
Instruções de Instalação..................................................... 22
Installatie-instructies........................................................... 26
Installationsvejledning.........................................................30
Asennusohjeet.................................................................... 34
Installeringsinstruksjoner.................................................... 38
Installationsinstruktioner..................................................... 42
Instrukcja instalacji..............................................................46
Pokyny pro instalaci............................................................ 50
Upute za instalaciju.............................................................54
安装说明............................................................................. 58
Garmin®, the Garmin logo, and Nexus® are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. gWind
™, GND™, and GMI™ are trademarks of Garmin Ltd. or its subsidiaries.
These trademarks may not be used without the express permission of Garmin.
NMEA 2000® and the NMEA 2000 logo are registered trademarks of the National Marine Electronics Association.
November 2016 190-01723-99_0EPrinted in Taiwan
TA-2013/1725
TA-2013/2433
gWind™ Wireless
Installation Instructions
Important Safety Information
WARNING
See the Important Safety and Product Information guide in the
product box for product warnings and other important
information.
CAUTION
Always wear safety goggles, ear protection, and a dust mask
when drilling, cutting, or sanding.
Use caution when working from heights.
This device provides wireless wind speed and wind angle
information to a NMEA 2000
® network on your boat. The wind
transducer transmits information to a Wireless Server Interface
(WSI) box, which must connect to a Garmin®GND™ 10 black box
bridge to send the data to a NMEA 2000 network.
Registering Your Device
Help us better support you by completing our online registration
today.
• Go to .http://my.garmin.com
• Keep the original sales receipt, or a photocopy, in a safe
place.
Battery Warnings
WARNING
If these guidelines are not followed, the battery may experience
a shortened life span or may present a risk of damage to the
device, fire, chemical burn, electrolyte leak, and/or injury.
• Do not disassemble, modify, remanufacture, puncture, or
damage the device or batteries.
• Do not immerse or expose the device or batteries to water or
other liquids, fire, explosion, or other hazard.
• Do not use a sharp object to remove batteries.
• Keep batteries away from children.
• Only replace batteries with correct replacement batteries.
Using other batteries presents a risk of fire or explosion. To
purchase replacement batteries, see your Garmin dealer or
the Garmin website.
• Do not operate the device outside of the following
temperature range: from -20° to 50°C (from -4° to 122°F).
• When storing the device for an extended time period, store
within the following temperature range: from 0° to 35°C (from
32° to 95°F).
• Contact your local waste disposal department to dispose of
the device/batteries in accordance with applicable local laws
and regulations.
Installing the Battery
NOTICE
The appropriate battery is provided with this device. Installing a
battery not provided by or purchased from Garmin may damage
the device.
Before mounting the device, you must install the included
battery.
1Using a #2 Phillips screwdriver, open the battery door on the
device.
2Insert the connector from the battery
À to the port on the
board inside the device Á.
The connector fits into the port only one way. Forcing the
connector into the port may damage it.
3Route the battery cable inside the device housing
Â, and
place the battery under the board
Ã.
4Taking care to avoid pinching the battery wires, close and
secure the battery door.
Installing the Propeller
1Ensure the shaft À lines up correctly with the slot on the
propeller.
The socket on the propeller fits only one way on the shaft.
2Press on the propeller until it is seated on the device.
3Install the set screw Á to hold the propeller securely to the
device.
Mounting Considerations
When selecting a mounting location for the wind transducer,
observe these considerations.
• The wind transducer should be mounted on a horizontal
surface on the mast head À.
2 Installation Instructions
• If there is not a horizontal surface on the mast head, an
appropriate shim must be added to create a horizontal
surface.
• The wind transducer should be installed facing the front of
the boat Á, parallel to the center line.
NOTE: If you do not mount the device facing the exact front
of the boat, you must configure the orientation to receive
accurate wind-angle data (Adjusting the Orientation,
page 4).
When selecting a mounting location for the wireless server
interface (WSI), observe these considerations.
• Before permanently mounting the WSI, you must test the
signal strength between the wind transducer and the WSI
( ).Testing the Signal Strength, page 3
• The WSI is not water resistant and must be installed in a
location that is not exposed to any spray, washdown, or
submersion.
• The best location for the WSI is under the deck, near the hull,
as high as possible in the boat.
• You should install the WSI as close to the wind transducer as
possible.
• Metallic objects in the path of the wind transducer and the
WSI greatly reduce the transmission distance.
• The antenna is on the top of the WSI Â, and works best
when it is pointing toward the wind transducer.
• The WSI works the best when installed on a bulkhead
parallel to the pole of the wind transducer, in a fore-aft
direction.
Installing the Mounting Bracket
1Using the mounting bracket as a template, mark the pilot hole
locations.
2Using a 4.5 mm (11/64 in.) bit, drill the pilot holes.
3Fasten the mounting bracket to the surface using the
included screws.
Securing the Device in the Mounting Bracket
1Loosen the lock nut À on the device by turning it counter-
clockwise by hand until it stops.
2Place the device in the mounting bracket by pushing it down
Á and sliding it back until it stops Â.
3Secure the device in the bracket by turning the lock nut
clockwise by hand until it stops.
4Attach the security clamp à to the device to prevent the lock
nut from loosening.
Mounting the WSI
Before permanently mounting the WSI, you must test the signal
strength between the sensor and the receiving box.
1Determine the mounting location.
2Using the device as a template, mark the pilot hole locations
on the mounting surface.
3Using a 1/8 in. drill bit, drill the pilot holes.
4Use the included screws to attach the device to the mounting
surface.
Testing the Signal Strength
Before you can permanently mount the WSI, you must test the
signal strength between the wind transducer and the WSI.
1Temporarily connect the WSI to the GND 10.
2If it is not connected already, connect the GND 10 to the
same NMEA 2000 network as a marine instrument.
3Go to a page on the marine instrument that shows wind data.
4Select an option:
• If no wind data appears on the marine instrument, move
the WSI to a new location and repeat step 3.
• If wind data appears on the marine instrument, note the
location and permanently mount the WSI.
WSI Box Connection Considerations
NOTICE
It is recommended to provide a direct 12 Vdc power supply to
the WSI box. It is mandatory to provide a direct 12 Vdc power
supply if any other units are connected to the Nexus
® network or
wired to the WSI box.
The WSI box must connect to a Garmin GND 10 black box
bridge to communicate with the NMEA 2000 network on your
boat. When connecting the included cable to the WSI box and to
the GND 10 bridge, observe these considerations.
Installation Instructions 3
Specyfikacje produktu
| Marka: | Garmin |
| Kategoria: | Morski |
| Model: | gWind |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Garmin gWind, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Morski Garmin
15 Sierpnia 2024
9 Sierpnia 2024
4 Lipca 2024
4 Lipca 2024
4 Lipca 2024
4 Lipca 2024
4 Lipca 2024
4 Lipca 2024
3 Lipca 2024
3 Lipca 2024
Instrukcje Morski
- Morski President
- Morski Lowrance
- Morski Fusion
- Morski IVT
- Morski ICOM
- Morski Simrad
- Morski Raymarine
- Morski Rockford Fosgate
- Morski Humminbird
- Morski Alphatron
- Morski Silva
- Morski Polmar
- Morski Eagle
- Morski Furuno
- Morski Klarfit
- Morski BandG
- Morski Dickinson Marine
- Morski Efoy
- Morski Navionics
- Morski Echotec
- Morski Interphase
- Morski Easy
- Morski Lofrans
- Morski Fastnet
- Morski KVH
- Morski Standard Horizon
- Morski SEAFARER
- Morski Nasa
- Morski Katadyn
- Morski Sailtron
- Morski Lorenz
- Morski Raytheon
- Morski Geonav
- Morski Digital Yacht
- Morski Plastimo
Najnowsze instrukcje dla Morski
5 Października 2024
28 Września 2024
28 Września 2024
28 Września 2024
28 Września 2024
28 Września 2024
28 Września 2024
28 Września 2024
28 Września 2024
27 Września 2024