Instrukcja obsługi Gamber-Johnson 7160-1584-00

Gamber-Johnson podstawa/stacja dokująca 7160-1584-00

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Gamber-Johnson 7160-1584-00 (6 stron) w kategorii podstawa/stacja dokująca. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/6
If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868
Form RevisionProduct
INSTALLATION INSTRUCTIONS
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brake lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
7160-1584-XX
F110 DOCKING STATION
Rev C INST-1052
Printing Spec: PS-001
© Copyright 2022 Gamber-Johnson, LLC
This instruction sheet is for the following products:
Item No. 7160-1584-00 No RF
Item No. 7160-1584-03 Tri-RF
Item No. 7160-1584-20 No RF WITH ACCELEROMETER
Item No. 7160-1584-23 Tri-RF WITH ACCELEROMETER
Item No. 7160-1584-30 No RF WITH ACCELEROMETER POWERED RS232
Item No. 7160-1584-33 Tri-RF WITH ACCELEROMETER POWERED RS232
Item No. 7160-1584-40 No RF WITH POWERED RS232
Item No. 7160-1584-43 Tri-RF WITH POWERED RS232
1/6
This instruction sheet is for the F110 docking station only. For instructions on features,
set-up, and operation of the F110 computer, please refer to the manual provided by
Getac with the computer.
This docking station is designed to be used with a variety of Gamber-Johnson mounting
systems. Installation instructions for other Gamber-Johnson products are provided with
each individual product.
During Installation:
DO NOT connect this docking station to the vehicle battery until:
All other electrical connections are made1.
Mounting of all components is complete2.
Verification that no shorts exist in the entire system3.
DO NOT install equipment or route wiring or cords in the deployment path of any air bag.
When drilling into the vehicle, DO make sure that both sides of the surface are clear of anything that
could be damaged.
CAUTION: If wiring is shorted to the frame, high current conductors can cause hazardous sparks
resulting in electrical fires or flying molten metal.
After installation:
Test the docking station to ensure that it is working properly.
File these instructions in a safe place and refer to them when performing maintenance or re-
installing.
WARNING: Failure to follow all safety precautions and instructions may result in property damage,
serious injury, or death.
IMPORTANT SAFETY INFORMATION FOR INSTALLERS
Safety is dependent on the proper installation and servicing of this docking station. It is important to
read and follow all instructions before installing this product.
To properly install a Gamber-Johnson docking station you must have a good understanding of
automotive electrical procedures and systems, along with proficiency in the installation and service of
aftermarket vehicle equipment.
There are no adjustments required at any time of the electrical components within the docking station.
Opening the docking station will void the product warranty.
Conduct a "Bench Test"
Gamber-Johnson strongly advises a "bench test" be conducted to verify all electronic and
software issues are resolved prior to installation:
Make sure the computer is operational by itself.1.
Insert computer into the docking station and verify that the computer is 2.
operating in the dock.
Interconnect entire assembly and verify start-up of all components, including 3.
other equipment (printers, modems, scanners, etc.)
Gamber-Johnson recommends positioning of all mounts and equipment in the vehicle
prior to the actual install to verify that mounting locations are safe and practical.
PRE-INSTALLATION RECOMMENDATOINS
2 / 6
F110 DOCKING STATION FEATURE IDENTIFICATON
MICROPHONE
HEADPHONE
VGA
HDMI
USB 3.0
(900 mA)
USB 2.0
(500mA)
ETHERNET
ANTENNA
PASS-THROUGH
(SMA)
POWER SUPPLY INPUT
19VDC
3/6
Serial Label
1/4-20 UNC Threaded
Inserts - 75mm VESA
Hole Pattern
Cable Restraint Bracket
Serial Ports
*Note: 7160-1584-3X & -4X
Models have power on PIN #9
Latch
Tri-RF Connector
Guide Pins
Connector
Lock

Specyfikacje produktu

Marka: Gamber-Johnson
Kategoria: podstawa/stacja dokująca
Model: 7160-1584-00

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Gamber-Johnson 7160-1584-00, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje podstawa/stacja dokująca Gamber-Johnson

Gamber-Johnson

Gamber-Johnson 7160-1883-00 Instrukcja

22 Sierpnia 2024
Gamber-Johnson

Gamber-Johnson 7170-0551-03 Instrukcja

22 Sierpnia 2024
Gamber-Johnson

Gamber-Johnson 7160-1642-00 Instrukcja

22 Sierpnia 2024
Gamber-Johnson

Gamber-Johnson 7160-1882-00 Instrukcja

22 Sierpnia 2024
Gamber-Johnson

Gamber-Johnson 7160-1584-00 Instrukcja

22 Sierpnia 2024
Gamber-Johnson

Gamber-Johnson 7160-1884-00 Instrukcja

22 Sierpnia 2024
Gamber-Johnson

Gamber-Johnson 7160-1882-10 Instrukcja

22 Sierpnia 2024

Instrukcje podstawa/stacja dokująca

Najnowsze instrukcje dla podstawa/stacja dokująca

I-TEC

I-TEC Thunderbolt 3 Instrukcja

28 Września 2024
I-TEC

I-TEC USB-C Metal Nano Docking Station Instrukcja

28 Września 2024
Karma

Karma Pocket Go Instrukcja

24 Września 2024
Karma

Karma BM 1015 Instrukcja

24 Września 2024
Karma

Karma BM 863RM Instrukcja

24 Września 2024
Havis

Havis DS-GTC-312-3 (Getac V110) Instrukcja

20 Września 2024
Havis

Havis DS-GTC-313-3 (Getac V110) Instrukcja

20 Września 2024
Havis

Havis DS-GTC-611-3 (Getac S410) Instrukcja

20 Września 2024
Havis

Havis DS-GTC-315-3 (Getac V110) Instrukcja

20 Września 2024
Havis

Havis DS-GTC-613-3 (Getac S410) Instrukcja

20 Września 2024