Instrukcja obsługi Friedland Evo Wirefree 200m - D412

Friedland dzwonek do drzwi Evo Wirefree 200m - D412

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Friedland Evo Wirefree 200m - D412 (1 stron) w kategorii dzwonek do drzwi. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/1
Evo Wirefree 200m* Chime Kit with Light
Instructions
Please retain these instructions for future reference
Pack contents:
Portable Door Chime with Light
Bell push & CR2032 Lithium coin cell battery
Adhesive pad,2xscrews(ø3xm)2xwallplugs (ø5 x 25mm)
for mounting the bell push
Fig. 6
Fig. 7
7. Programming a second push
Within 5 minutes of pressing the first push, press the second
push
until the chime sounds, then use button B to change the tune
if required.
If more than 5 minutes has elapsed since the first push was
programmed, press and hold both buttons A and B until the chime
sounds, this takes approx 5 seconds. The chime is now cleared
and can programmed to one or two door pushes
All EVO and Décor Chimes and Bell Pushes use programming
to ensure no interaction from other neighbouring systems.
8. Sound Selection
A = Main push sound selection
B = Second push sound selection
Chime tune options are as follows:
1. Big Ben 2 Note (Default Tune for 1st Push)
2. Mini Bell 4 Note w/ Echo (Default Tune for 2nd Push)
3. Clarinet
4. Altosax
9. Flashing Light and sound controls
The settings are:
0. Sound only
1. Sound with flashing light
2. Flashing light only
Flashing Light and sound control
To turn the door chime sound off or to stop
the flashing LED light when the bell push
is pressed, turn knob C
Note: when the chime is being programmed
this control will not function for 5 minutes.
Trouble Shooting
Chime not Sounding
Batteries may not be inserted correctly
Check all batteries have been inserted correctly
Chime may be positioned out of range of the bell push
Move your chime closer to the bell push
Note:
During the programming cycle the transmission range may be reduced
The chime will resume optimum range after 5 minutes
A metallic object may be blocking the signal from bell push position
Experiment with the location of the chime to see if you can move it in a
more suitable place
The battery in the bell push may need replacing
Press the bell push. If the confidence light (D) flashes 5 times after
being pushed, replace the battery
Note: In cold conditions, poor location or environment, operating at
maximum range it is advisable to replace the battery more frequently
before the indicator light flashes
(i.e every 12 - 18 months) to maintain optimum performance
Your bell push and chime haven't been programmed
Do the automatic programming of your chime and bell push
The Selection knob may have been set incorrectly
Do position of knob C as described in section 8 above
LED flashing light does not flash
The selection knob is not set correctly, reset position of knob C as
described in section 8 above
A
C
B
02
1
C
LED light
Declaration
Novar ED&S hereby declares that this wirefree product is in compliance with
the essential requirements and other relevant provisions of the Radio and
Telecommunications Terminal Equipment ( R & TTE ) directive, 1999/5/EC
GB
Fig. 8
-
+
+
-
+
-
Friedland guarantees this product for 3 years from date of purchase.
Proof of purchase is required, this does not affect your statutory rights.
If you require further information about our products, call the Friedland helpline
on 01268 563066.
Friedland, The Arnold Centre, Paycocke Road, Basildon, Essex, SS14 3EA, England
www.friedland.co.uk
Fig. 1
Fig. 2
Novar ED&S h
the essential
Telecommuni
8. Sound Se
A = Main pus
B = Second p
Chime tune o
1. Mini Bell 2
2. Mini Bell 1
3. Flugel Hor
Friedland guaran
Proof of purchas
If you require fur
on 01268 56306
Friedland, The A
www.friedl
Fig. 3
A
Fig. 4
B
Trouble Sh
Chime not S
Batteries m
Check all ba
Chime may
Move your c
Note: During
be reduced.
The chime w
A metallic ob
Experiment w
in a more su
The battery
Press the be
being pushe
Note: In cold
maximum ra
frequently be
(i.e every 12
Your bell pu
Do the autom
+
All EVO a
to ens
You will require:
3 X LR6 (AA) Alkaline batteries for the Door Chime
Only long-life Alkaline batteries must be used
A small crosshead and flathead screwdriver, a ø5mm. masonry drill
Installation
*Please note: The stated range of this product is measured in open
field conditions. Walls, ceilings and the positioning the bell push or
door chime on or near metal structures or reinforced PVC doors or
doorframes will reduce the transmission range.
1. Open the bell push
To open the front cover carefully
insert a flat bladed screw driver, into
the slot and twist gently (A). When
refitting the front cover to ensure the
weather proofing is maintained,
always mount the bell push in the
upright position and replace the
cover securely. Fig. 1
2. To fit or replace the battery
Open the front cover and
insert the CR 2032 Lithium
coin cell battery into the cover
as shown in Fig. 2.
3. Mount the bell push
Ensure the wall surface is clean and dry.
Mount using either the double sided
sticky pad on a smooth surface, or the
screws and wall plugs provided, See Fig 3.
Do not mount the push on or near (< 30cm)
large metal objects, as it will block signals
from the push. Next, hook the cover at
the top, then press down at the bottom to
clip in place.
4. Test the bell push
When the bell push button is pressed,
the confidence light (B)
in Fig. 4, will
illuminate to reassure the caller that
the bell push is
working.
The light will flash 5 times when
the battery needs replacing
5. Fit the Door chime batteries
Remove battery compartment cover and insert three LR6 (AA)
alkaline batteries as shown in Fig. 8.
The first time a chime unit is powered up, the sounds available
are demonstrated.
6. Automatic Programming of bell pushes
First, place the chime close to the door push (within 8m/ 25ft)
to program the chime and check that it is working.
Press the door push until the chime responds with a tune.
You can leave this tune or change the tune by using button A
(see Fig. 6, sound selection).
10. Replacing Batteries
First remove decorative cover
and replace with three LR6 (AA)
alkaline batteries. (Fig. 8)
When replacing batteries the
chime is still programmed
and can be used straight away.


Specyfikacje produktu

Marka: Friedland
Kategoria: dzwonek do drzwi
Model: Evo Wirefree 200m - D412

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Friedland Evo Wirefree 200m - D412, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje dzwonek do drzwi Friedland

Instrukcje dzwonek do drzwi

Najnowsze instrukcje dla dzwonek do drzwi

Gira

Gira 2506 20 Instrukcja

15 Października 2024
Panasonic

Panasonic VL-VM902EX Instrukcja

12 Października 2024
Elro

Elro DB260F Instrukcja

10 Października 2024
Eufy

Eufy Video Doorbell C30 Instrukcja

9 Października 2024
Velleman

Velleman HAM9011 Instrukcja

9 Października 2024
CATA

CATA CK 6000 X Instrukcja

8 Października 2024
CATA

CATA THALASSA 600 GWH Instrukcja

8 Października 2024