Instrukcja obsługi Flyzone Calypso

Flyzone Zabawki sterowane radiem Calypso

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Flyzone Calypso (4 stron) w kategorii Zabawki sterowane radiem. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/4

REQUIRED FOR COMPLETION

In addition to the items listed in the instruction manual for the

Rx-R edition, the Calypso ARF also requires the following items:

❍ 18A (Electronic Speed Controller) (FLZA6011)ESC

❍ C28-30 1300kV (FLZA6012)brushless motor

❍ Spinner, folding (FLZA6006)propeller set

❍ (4) Calypso micro servos (FLZA6013), or any of the

Futaba® micro servos that have the same case as the

S3117 such as the following:

◗ S3117 (FUTM0417)

◗ S3157 (FUTM0657)

◗ S3156 (FUTM0656)

❍ (2) 18"–24" [460 mm – 610 mm] servo wire extensions

for aileron servos (HCAM2200 for Futaba J)

❍ The ailerons may be mixed electronically through the

mixing in your transmitter, or “hard-wired” together into

the same channel with a (FUTM4130).Y-harness

❍ The Calypso may be assembled with just about any kind

of glue including foam-safe or regular CA, but for gluing

in the servos something thicker and ﬂ exible is preferred

such as Zap Goo or similar (PAAR3200).

❍ A 1.5mm is required for tightening the set Allen wrench

screws in the folding propeller hub (DTXR0288).

❍ Non-permanent threadlocker for all metal-to-metal screws

(GPMR6060)

ASSEMBLY

Assemble the Wings

First, let’s center the aileron servo arms before gluing the

servos into the wing…

❏ 1. Temporarily connect the aileron servos and ESC to your

receiver and turn on your transmitter. Making sure the trims

on your transmitter are centered, connect the battery to the

ESC. If necessary, remove and re-mount the servo arms so

they will be perpendicular as shown. Be certain to replace

the servo arm screws.

You may work on both wings simultaneously, or do one

wing at a time.

❏ 2. Without using any glue, temporarily ﬁ t the servos into the

pockets in the wing. Hook up the ailerons with the hardware shown.

❏ 3. Connect a 18" – 24" [460mm – 610mm] servo extension

to the aileron servo wires and secure the connection with tape,

Manual Supplement

Refer to this Instruction Manual Supplement

for initial assembly of your Calypso ARF.

After completing the assembly steps in

this supplement, continue with the twenty-

page RTF / Rx-R / Tx-R Calypso instruction

manual booklet.

heat shrink tubing or a dab of glue. Lay the servo wires down

inside the channels.

❏ 4. If you plan to hook up the optional ﬂ aps, it will be a

little easier to cut the ﬂ ap servo openings in the bottom wing

covers and ﬁ t the ﬂ ap servos at this time, so go ahead and

do so—but ﬁ rst refer to the illustration at step 13 on page 11

of the Calypso instruction manual for the correct orientation

of the ﬂ ap servos and servo arms. If unsure whether or not

you will be using ﬂ aps, the servo installation and hookup is

easy enough to retroﬁ t later (as illustrated on page 8 of the

instruction manual).

❏ 5. Without using any glue, test-ﬁ t the bottom wing cover to

the wing. Make sure the cover lays all the way down ﬂ at into

the cavity and make any adjustments necessary.

❏ 6. Glue the aileron servos (and ﬂ ap servos if installed) into

position—thick or medium CA is suitable, but if ever necessary,

the servos will be easier to extract later if something more

ﬂ exible such as Zap Goo or similar is used.

❏ 7. Glue the bottom wing cover into position—thick or medium

CA is okay here, but not to allow any glue to leak into use care

the channel or into the clamp for the joiner tube. If necessary,

use tape or weights to hold the cover down until the glue

hardens.

❏ 8. Glue the spars and optional aileron pushrod covers into

position. Also apply a strip of white or clear tape over the

channel for the aileron servo wire.

Assemble the Fuselage

Non-permanent threadlocker

should be used on all screws

that thread into metal such as

the motor mount screws, the

set screws in the propeller hub

and the screws that secure the

spinner—a large amount of

threadlocker is not required—

just enough to “wet” the ﬁ rst few

threads.

❏ 1. Guide the motor wires through the oval hole in the bottom

of the motor mount. Then, mount the motor with the two 3 x

5mm screws (don’t forget to use threadlocker on the screws).

❏ 2. Fasten the propeller hub onto the motor shaft using a

1.5mm hex wrench to tighten the set screws. Then, mount the

spinner with the 3 x 12mm screws.

❏ 3. Connect the ESC to the motor and mount the ESC to the

inside of the fuselage with strips of the included adhesive-back

hook-and-loop material. Note: If, while running up the motor

later, the propeller turns backward, simply switch any two of

the three motor wires with each other to make the motor turn

the other direction.

Specyfikacje produktu

Marka:	Flyzone
Kategoria:	Zabawki sterowane radiem
Model:	Calypso

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Flyzone Calypso, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Zabawki sterowane radiem Flyzone

Flyzone Calypso Instrukcja

30 Września 2024

Flyzone A6M2 Zero Instrukcja

30 Września 2024

Flyzone B-25 Mitchell Instrukcja

30 Września 2024

Flyzone Cessna 182 Skylane Instrukcja

30 Września 2024

Flyzone Seawind Instrukcja

30 Września 2024

Flyzone Sensei FS Instrukcja

30 Września 2024

Flyzone Extra 300 SX Instrukcja

30 Września 2024

Flyzone DHC-2 Beaver Instrukcja

30 Września 2024

Flyzone Super Cub Instrukcja

30 Września 2024

Flyzone Micro Calypso Instrukcja

14 Września 2024

Instrukcje Zabawki sterowane radiem

Najnowsze instrukcje dla Zabawki sterowane radiem

Spektrum AR6600T Instrukcja

15 Października 2024

Amewi Hyper Go Instrukcja

9 Października 2024

Carson Drift Burner Instrukcja

9 Października 2024

Carson Micro X-Warrior 2.0 Instrukcja

9 Października 2024

Hobbywing XeRun XR10 Pro WP Instrukcja

9 Października 2024

Hobbywing XeRun XR10 Stock Spec G2 Instrukcja

9 Października 2024

Hobbywing XeRun XR10 Justock G3S Instrukcja

9 Października 2024

Hobbywing XeRun XR8 PRO G3 Instrukcja

9 Października 2024

Hobbywing XeRun XR10 Justock G3 Handout Instrukcja

9 Października 2024

Hobbywing XeRun XR8 Plus G2S Instrukcja

9 Października 2024