Instrukcja obsługi Flir N233ZD

Flir Kamera monitorująca N233ZD

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Flir N233ZD (1 stron) w kategorii Kamera monitorująca. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/1
PACKAGE CONTENTS:
1x CD
1x Micro PT IP Camera
Quick Start Guides
Installing the Camera
A
2.1MP HD IP Micro PT Camera
N233ZD
Quick Connection Guide
B
• Use an appropriate low voltage power cable to prevent fire or electrical
shock.
• Make sure to install the camera in an area that can support the camera
weight.
• There are no user serviceable parts inside the camera. Please do not
disassemble the camera.
• Do not clean the lens cover with an abrasive cleaning material. Please use
a lint free micro-fiber cloth to clean the lens cover.
• Camera is rated for outdoor use (IP66), but is not intended for submersion
in water.
Safety PrecautionsWeights & Dimensions
C
Installing the Camera Connecting the Camera (continued)
0.6lbs / 0.3kg
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
FCC Notice
1 2 3
1x Allen Key
1. Ethernet Port: Connect the camera to an NVR or a router or
switch on your network using Cat5e or better Ethernet cable
(not included). PoE Class 3 supported.
2. Power Input: If not using PoE, connect the camera to a 12V
DC power source (300mA or higher required).
Remove the vinyl film from the camera lens once installation is
complete.
Information in this document is subject to change
without notice. As our products are subject to continuous
improvement, FLIR Systems, Inc. and our subsidiaries reserve
the right to modify product design, specifications and
prices, without notice and without incurring any obligation.
E&OE © 2014 FLIR Systems, Inc. All rights reserved.
www.flirsecurity.com/pro
For support, visit
Latest software and manuals available on
www.flirsecurity.com/pro
N233ZD_QCG_EN_R1
Weight
2.3” /
58mm
Connect cables as shown in the section “Connecting the Camera”.
D
Align the 3 notches on the side of the dome camera with the
3 corresponding pegs on the mounting plate. Push the camera
gently into the mounting plate until you hear a ‘click‘.
3x Mounting Screws
Use the included mounting template to mark holes for the
mounting screws and camera cable.
Drill holes for the mounting screws and camera cable.
NOTE: Use the included drywall anchors if installing on a drywall
surface.
Align the metal mounting plate so that the 3 screw holes in the
plate line up with the 3 holes drilled in the wall.
Attach the flat side of the mounting plate to the surface using the
included mounting screws (3x).
1
2
3x Drywall Anchors
Inserting the microSD Card
Resetting the Camera
5.1” /
130mm
ERemove the M2x5 screw from the side of the camera using the
included Allen key.
Drywall anchors (3x)
Mounting surface
Mounting plate
Mounting screws (3x)
M2x5 screw
F
H
I
J
NOTE: The pegs and notches only align one way. Do not force
the camera to fit into the mounting plate.
Notches (x3)
Pegs (x3)
Re-insert the M2x5 screw removed in Step E. Tighten firmly using
the included Allen key.
G
Ensure the camera is grounded with the
pre-inserted M2x5 screw.
A
B
Separate the camera from the mounting plate if needed.
Remove the 2 screws from the compartment
cover using a Phillips screwdriver (not included).
C
D
Slide the microSD carriage cover to open, then
lift upward.
Place a microSD card (not included) into the
carriage with the metal contacts facing down.
OPEN
LOCK
A
B
C
Separate the camera from the mounting plate
if needed.
Remove the 2 screws from the compartment
cover using a Phillips screwdriver (not included).
Press and hold the reset button for 4 seconds.
OPEN
LOCK
Close and lock the carriage cover. Replace the
compartment cover on the camera base.
E
Reset button
Replace the compartment cover on the
camera base.
D
1x Mounting Plate 1x Mounting Template
GND port

Specyfikacje produktu

Marka: Flir
Kategoria: Kamera monitorująca
Model: N233ZD

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Flir N233ZD, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Kamera monitorująca Flir

Flir

Flir T4390BT Instrukcja

13 Września 2024
Flir

Flir Quasar CM-6308 Instrukcja

13 Września 2024
Flir

Flir M42046 Instrukcja

13 Września 2024
Flir

Flir F-313 Instrukcja

12 Września 2024
Flir

Flir Quasar CM-4321 Instrukcja

11 Września 2024
Flir

Flir N233VE Instrukcja

11 Września 2024
Flir

Flir Summit DBV54DL Instrukcja

11 Września 2024
Flir

Flir M617CS Instrukcja

11 Września 2024
Flir

Flir Summit DBB43TL Instrukcja

10 Września 2024
Flir

Flir DH2589TBB Instrukcja

9 Września 2024

Instrukcje Kamera monitorująca

Najnowsze instrukcje dla Kamera monitorująca

Dahua Technology

Dahua Technology Pro IPC-HDPW5442G-Z Instrukcja

15 Stycznia 2025
Toshiba

Toshiba IKS-WR7412 Instrukcja

13 Stycznia 2025
AVerMedia

AVerMedia FC1320-P Instrukcja

13 Stycznia 2025
Digitus

Digitus OptiMax DN-16037 Instrukcja

13 Stycznia 2025
Hikvision

Hikvision DS-2CE59U1T-AVPIT3ZF Instrukcja

12 Stycznia 2025
Hikvision

Hikvision IDS-2CD7526G0-IZHSY Instrukcja

12 Stycznia 2025
Hikvision

Hikvision DS-2CD2163G0-I(S) Instrukcja

12 Stycznia 2025
Hikvision

Hikvision DS-2CD2H83G1-IZS Instrukcja

12 Stycznia 2025
Speco Technologies

Speco Technologies O5LB1 Instrukcja

12 Stycznia 2025
ZKTeco

ZKTeco AntarVis 2.0 Instrukcja

12 Stycznia 2025