Instrukcja obsługi Flir N233VE

Flir Kamera monitorująca N233VE

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Flir N233VE (1 stron) w kategorii Kamera monitorująca. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/1
PACKAGE CONTENTS: Installing the Camera Installing the Camera (continued)
3MP IP Vandal Dome Camera
N233VE
Quick Connection Guide
• Use an appropriate low voltage power cable to prevent fire or
electrical shock.
• Make sure to install the camera in an area that can support the
camera weight.
• There are no user serviceable parts inside the camera. Please do not
disassemble the camera.
• Do not clean the lens cover with an abrasive cleaning material. Please
use a lint free micro-fiber cloth to clean the lens cover.
• Camera is rated for outdoor use (IP66), but is not intended for
submersion in water.
Safety PrecautionsInserting the microSD Card
Resetting the Camera
Weights & Dimensions
Connecting the Camera
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
FCC Notice
1 2 3
Information in this document is subject to change
without notice. As our products are subject to continuous
improvement, FLIR Systems, Inc. and our subsidiaries reserve
the right to modify product design, specifications and
prices, without notice and without incurring any obligation.
E&OE © 2015 FLIR Systems, Inc. All rights reserved.
N233VE_QCG_EN_R1
1 x CD
1 x IP Vandal Dome Camera
Quick Start Guides
1 x Allen Key
3 x Mounting Screws 3 x Drywall Anchors
1 x Mounting Template
1 x RJ45 Waterproof Cap
0.8lb /
0.4kg
Weight
For support, visit
Latest software and manuals available on
www.flir.com/security/support
www.flir.com/security/support
A
A
A
B
B
B
C
C
C
D
D
E
E
Use the included mounting template to mark holes for
the mounting screws and camera cable.
Use the included Allen key to loosen the screws on the
dome cover. Remove the dome cover.
Remove the dome cover. Make sure the camera is powered on.
Remove the dome cover.
Slide the metal cover down to open it.
Reset button microSD slot
Insert the microSD card (not included)
into the slot.
Close the cover and slide it up to lock
the microSD card in place.
Replace the dome cover. Tighten the dome cover screws (3x).
Replace the dome cover. Tighten the dome cover screws (3x).
Press and hold the reset button on the camera base for 5 seconds to
reset the camera to default settings.
Drill holes for the mounting screws and camera cable.
Connect cables as shown in the section “Connecting the
Camera”.
Attach the camera base to the mounting surface using
the included mounting screws (3x).
NOTE: Use the included drywall anchors if installing into
drywall.
F
G
H
Set the position and angle of the camera.
Rotate the camera around the base (rotates 360°
before it is stopped).
Use a Phillips screwdriver to loosen the adjustment
screws on both sides of the camera module. Tilt the
camera module. Tighten both screws when finished.
Adjust the position of the camera lens by twisting the
camera lens housing.
Replace the dome cover. Use the included Allen key to
tighten the screws (3x).
Remove the vinyl film from the dome cover.
ATTENTION: Make sure IR LEDs are not blocked
by the dome cover to prevent IR reflection.
3.2” /
81mm
4.3” /
110mm
1 2 3
Power Input: If not using PoE, connect the camera to a
12V DC power source (370mA or higher required).
Alarm I/O (Optional): Connect alarm/sensor devices (not
included).
Ethernet Port: Connect the camera to an NVR or a router
or switch on your network using Cat5e or better Ethernet
cable (not included). PoE Class 3 supported.
NOTE: Install the included RJ45 waterproof cap if needed.
Audio I/O (Optional): See the Instruction Manual for
details.
1.
2.
3.
4.
1 2 34
1.
2.
3.
Mounting screws (3x)
Drywall anchors (3x)

Specyfikacje produktu

Marka: Flir
Kategoria: Kamera monitorująca
Model: N233VE

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Flir N233VE, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Kamera monitorująca Flir

Flir

Flir T4390BT Instrukcja

13 Września 2024
Flir

Flir Quasar CM-6308 Instrukcja

13 Września 2024
Flir

Flir M42046 Instrukcja

13 Września 2024
Flir

Flir F-313 Instrukcja

12 Września 2024
Flir

Flir Quasar CM-4321 Instrukcja

11 Września 2024
Flir

Flir N233VE Instrukcja

11 Września 2024
Flir

Flir Summit DBV54DL Instrukcja

11 Września 2024
Flir

Flir M617CS Instrukcja

11 Września 2024
Flir

Flir Summit DBB43TL Instrukcja

10 Września 2024
Flir

Flir M400XR Instrukcja

7 Września 2024

Instrukcje Kamera monitorująca

Najnowsze instrukcje dla Kamera monitorująca

Trebs

Trebs CCD-401C Instrukcja

15 Października 2024
Hikvision

Hikvision DS-2CE56D5T-AIRZ Instrukcja

15 Października 2024
D-Link

D-Link DCS-7510 Instrukcja

15 Października 2024
Ubiquiti Networks

Ubiquiti Networks UniFi Video UVC-G3-AF Instrukcja

14 Października 2024
Hikvision

Hikvision DS-2TD2137-7/VP Instrukcja

13 Października 2024
Alecto

Alecto DVC-215IP Instrukcja

13 Października 2024
Hikvision

Hikvision DS-2DE7A245IX-AE/S1 Instrukcja

13 Października 2024
Hikvision

Hikvision DS-2TD2166-15/V1 Instrukcja

13 Października 2024
Hikvision

Hikvision DS-2CD2325FWD-I Instrukcja

13 Października 2024
Hikvision

Hikvision DS-2CD2323G2-IU Instrukcja

12 Października 2024