Instrukcja obsługi Fisher & Paykel 23986

Fisher & Paykel nieskategoryzowany 23986

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Fisher & Paykel 23986 (2 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

Refrigerator Surround Kit

Installation instructions

E402B, E442B, E522B, RF610A, RF540, RF522A models NZ AU GB AE HK SG IE US CA EU CN IN

Important!

SAVE THESE INSTRUCTIONS

The model shown in this document may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to our website

www.fisherpaykel.com or contact your local Fisher & Paykel dealer.

3 Parts suPPlied

Top trim (x 1)

Side trim (x 2)

Bottom trim

(x 1)

Side trim

brackets (x 10)

Side trim

brackets (x 4)

Side trim centre

brackets (x 6)

Top trim brackets:

– Single

refrigerator kits

(2 x brackets)

– Side by Side kits

(3 x brackets)

Screw type A:

#8 x 12 Pozi

Drive CSK (x 26)

Long screws

10 x 75 CSK PH

P/no SP0207

(x 2)

Floor stops

P/no 460912

(x 2)

Washers

4 x 11 x 1mm

(x 2)

6 seCure side

trim braCkets

Locate the ten side trim brackets.

Position five brackets to the left hand side of

the cabinet and the remaining five brackets to

the right hand side of the cabinet.

Brackets should be evenly spaced down each

side (see diagram 3a/b). Secure each of these

brackets with the two screws provided.

Care must be taken to line up the front edge

of the brackets with the leading edges of

thecabinet.

Diagram 3b

Diagram 3a

7 seCure Floor stoPs

Two floor stops are supplied to prevent the refrigerator from being pushed too far back into the cavity.

These are mounted on the base or floor at a distances of 688mm (27") from the face front edge of the

trim kit.

688 mm

150 mm

Diagram 4

4 Cabinetry dimensions

Diagram 1a

Cabinet at floorlevel

Diagram 1b

Cabinet above toekick

C1C2

Installation diagrams for illustration purposes only Diagram 1

Cutout dimensions – flush to edge of door (mm / inches)

635 (25") model

680 (26 /") model

790 (31 /") model

900 (35 /") model

635 (25") model

+ 635 (25") model

680 (26 /") model

+ 680 (26 /") model

790 (31 /") model

+ 790 (31 /") model

Awidth 807 (31 ⁄”) 852 (33 ⁄”) 962 (37 ⁄”) 1072 (42 ⁄”) 1467 (57 ⁄”) 1557 (61 ⁄”) 1777 (70”)

Bdepth* 700 (27 ⁄”) 700 (27 ⁄”) 700 (27 ⁄”) 700 (27 ⁄”) 700 (27 ⁄”) 700 (27 ⁄”) 700 (27 ⁄”)

C1height** 1790 (70 /") 1790 (70 /") 1790 (70 /") 1875 (73  ⁄ ") 1790 (70 /") 1790 (70 /") 1790 (70 /")

C2height*** 1806 (71 /") 1806 (71 /") 1806 (71 /") 1891 (74 /") 1806 (71 /") 1806 (71 /") 1806 (71 /")

Dair vent

depth 200 (8”) 200 (8”) 200 (8”) 200 (8”) 200 (8”) 200 (8”) 200 (8”)

Eair vent

width 502 (19 /") 547 (21 ⁄") 657 (25 /") 767 (30 /") 1162 (45 ⁄") 1252 (49 ⁄") 1472 (58")

* Depth is a minimum requirement

** Height is without 16mm MDF packer

*** Height is with 16mm MDF packer

Cut out dimensions above are to be used as dimensions.minimum

5 seCure toP

trim braCkets

Locate the two/three top trimbrackets.

For the Side By Side Refrigerator kits, one

bracket is to be screwed in the top centre of the

cabinet, secure the top bracket with two of the

screws (Type A, #8 x 12 PoziDrive CSK).

For all other kits, the two brackets are to be

secured on either side, by two screws which are

mounted from the side (seediagram 2).

Looking at the front of the product, place the

top brackets on top of the woodencabinet.

Care must be taken to line up the top front

edge of the brackets with the leading edge of

the cabinet.

Hint: Holes should be drilled in the centre of

the slot in the brackets to allow for adjustment.

End bracket Centre bracket

Diagram 2

1 reFrigerator surround kit

This kit is designed to be used with models with a cabinet height of

between: 1695mm – 1806mm (66 ¾”–71 /”) with curved or flat door styling.

Youcan find the part number for each installation type in Section 10.

To give the most integrated look, the kitchen cabinetry should be flush with

the front of the refrigerator door.

Tools required (not included)

No. 2 drill bit – long

Electric drill

Phillips screwdriver

1 x 16mm ( inch) piece of MDF the same size as the base of the cavity ⁄

(optional). Not needed if refrigerator cabinet is sitting directly on the floor

and not on raised toe kickarea

Joiner kit (part number 819264) required if joining two refrigerators side by side

Before starting

All dimensions are internal or cut out dimensions.

The refrigerator can be installed:

1. In a cavity with a toe kick under the product with the bottom trim fitted to the base (diagram 1b/5).

2. In a cavity with 16mm panel under the product with the bottom trim fitted to the panel

(diagram 1a/6).

3. In a cavity where the product is at floor level with no bottom trim (diagram 1a).

4. Check whether your fridge has hinges concealed by the front of the fridge door. If unsure refer to

page 2 note*** for instructions.

2 getting started

Check that the internal Cupboard Cavity dimensions are correct (see diagram 1a/b).

Unpack the refrigerator and/or freezer cabinets from their separate delivery cartons (see individual

cartons for unpacking procedures).

Ensure the floor and/or the cupboards are protected from damage during the unpacking and

assembly of the cabinets.

Check the refrigerator and freezer doors are hinged on the desired side.

Check that the kit is complete (refer to Parts Supplied in section 3).

Note 1: Due to the size of the refrigerator cabinets, it is essential that assembly of the kit be undertaken

with a minimum of two able-bodied persons.

Note 2: It is important to include adequate venting to the top of the cabinet to ensure the efficient

operation of the refrigerator.

Note 3: The installation of the cabinet or cabinets can be at floor level as shown in diagram 1a or installed

above the toe kick board as in diagram 1b.

Note 4: Rollers and feet must be fitted.

Note 5: Cabinets installed above the toe kit should have a floor base constructed to support the total

weight of the loaded cabinet or cabinets placed on it.

The placement of the 16mm ( ") MDF or plywood under the cabinet or cabinets on either installation /

type is to allow the fitment of the bottom trim that covers it. It is optional.

10 kit Part numbers and Cut out dimensions table

Refrigerator Model

Kit Part Numbers Cut Out Dimensions

Brushed

Stainless

Plus

Joiner

Kit

Width

Depth

Height

C**

1 x 635

(25")

807

635

1790

23980 807mm

31 ⁄”

700mm

27 /”

1790mm

70 /”

1 x 635

(25")

807

635

1790

23981 807mm

31 ⁄”

700mm

27 /”

1790mm

70 /”

2 x 635

(25")

1467

635635

1790

23982 819264 1467mm

57 /”

700mm

27 /”

1790mm

70 /”

1 x 680

(26 /")

852

680

1790

23983 852mm

33 ⁄”

700mm

27 /”

1790mm

70 /”

1 x 680

(26 /")

852

680

1790

23984 852mm

33 ⁄”

700mm

27 /”

1790mm

70 /”

2 x 680

(26 /")

1557

680 680

1790

23985 819264 1557mm

61 / ”

700mm

27 /”

1790mm

70 /”

9 moVe into CaVity

If installing two refrigerators/

freezers side by side a joiner

kit is required. Refer to these

instructions and fit joiner kit

before pushing refrigerator into

place, see diagram6.

Plug refrigerator into electrical

socket, run water connection

to refrigerator if required

(Ice&Water models only).

Gently install refrigerator into

cabinetry making sure it is

centred within the surroundtrim.

The front of the refrigerator

door should be flush with the

front of the cabinetry to obtain

anintegratedlook.

Ensure the front leveling feet are

adjusted to take the load of the

fridge and keep it in place.

Optional

Diagram 6

8 trim installation

The bottom trim is designed to cover the front edge of the

floor base panel of the cabinet. This trim can be installed

on a raised toe kick (diagram 1a) or toe kick below the

refrigerator (diagram 1b)

Remembering that if this trim is to be used with the

refrigerator at floor level the cut out dimensions will need

to have 16mm ( ") added to its height to allow for the /

bottom trim to be fitted. Note this trim is optional on this

type ofinstallation. If used with a raised toe kick the 16mm

packer should be part of the base (diagram5). Therefore

16mm is not required to be added to the height dimension.

1. If used place the 16mm (/") piece of plywood or

with bottom trim fitted into the cavity (diagram 5 or 6).

Note the piece should be the same size as the base of

the cavity.

2. Remove protective coating film from surround trim.

3. To install the surrounds, first clip in the top surround.

Ensure the locator strips at the rear of the top brackets clip

into the rear of the top trim.

4. Clip both side trims into place starting from the front

cabinet edge.

16mm (/ inch)

plywood or MDF

board insert

Part of base

Diagram 5

Refrigerator Model

Kit Part Numbers Cut Out Dimensions

Brushed

Stainless

Plus

Joiner

Kit

Width

Depth

Height

C**

1 x 790

(31 /")

962

790

1790

23986 962mm

37 /”

700mm

27 /”

1790mm

70 /”

1 x 790

(31 /")

962

790

1790

23987 962mm

37 /”

700mm

27 /”

1790mm

70 /”

2 x 790

(31 /")

1777

790790

1790

23988 819264 1777mm

70”

700mm

27 /”

1790mm

70 /”

1 x 900

(35 /")

(French door

model)

1072

900

1875

23989 1072mm

42 ¼”

700mm

27 /”

1875mm

73  / ”

1 x 790

(31 /")

(French door

model)

962

790

1790

23990 962mm

37 /”

700mm

27 /”

1790mm

70 /”

* Depth is a minimum requirement

** Height is without 16mm MDF packer

*** For refrigerators / freezers where the hinge is not concealed

by the door refer to spare parts for the correct kit number.

820413 D should list non concealed number kit.

Before you call for service or assistance ...

Check the things you can do yourself. Refer to the installation instructions, your User Guide – inparticular

the troubleshooting section and check that:

your product is correctly installed.

you are familiar with its normal operation.

If after checking these points you still need assistance or parts, use the link at

www.fisherpaykel.com for regional service providers.

839254 A NZ AU GB AE HK SG IE US CA EU CN IN 09.13

Concealed Hinge Non Concealed Hinge

Specyfikacje produktu

Marka:	Fisher & Paykel
Kategoria:	nieskategoryzowany
Model:	23986
Kolor produktu:	Stal nierdzewna
Wysokość produktu:	1790 mm
Szerokość produktu:	962 mm
Głębokość produktu:	700 mm
Model:	Części AGD
Typ napędu:	Lodówka
Materiały:	Stal nierdzewna
Kompatybilność marki:	Fisher & Paykel
Odpowiedni dla:	Lodówka