Instrukcja obsługi Ferm TCM1012

Ferm maszyna do cięcia TCM1012

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Ferm TCM1012 (16 stron) w kategorii maszyna do cięcia. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/16

www.ferm.com

EN Original instructions 02

DE Übersetzung der

Originalbetriebsanleitung 04

NL Vertaling van de oorspronkelijke

gebruiksaanwijzing 06

FR Traduction de la notice originale 08

ES Traducción del manual original 11

TILE CUTTER

TCM1012

TILE CUTTER

Thank you for buying this Ferm product.

By doing so you now have an excellent product,

delivered by one of Europeís leading suppliers.

All products delivered to you by Ferm are

manufactured according to the highest standards

of performance and safety. As part of our

philosophy we also provide an excellent customer

service, backed by our comprehensive Warranty.

We hope you will enjoy using this product for

many years to come.

Read the operating instructions

carefully before using this device.

Familiarize yourself with its functions

and basic operation. Service the device

as per the instructions to ensure that it

always functions properly. The

operating instructions and the

accompanying documentation must be

kept in the vicinity of the device.

Contents

1. Technical specifications

2. Safety instructions

3. Assembly

4. Use

5. Maintenance

1. Technical specifications

max. 10 mm

max. 400 mm

30-80 mm

0-45°

2. Special safety instructions

1. The tile cutting machine is fitted with a

replaceable circular blade. Therefore, keep

children away.

2. After use the machine must be stored in a

safe and dry place, away from children.

3. This machine has been designed for cutting

and breaking glazed tiles, and must not be

used for any other purpose.

4. When using the tile cutting machine make

sure to keep extension leads and such away

from the machine.

5. Always place the tile cutting machine on a

level and firm surface.

6. CAUTION! The edges of cut tiles are sharp.

3. Assembly

Assemble the tile cutting machine as shown in the

drawing.

Assembly of the tile cutting machine

Remove all the parts from the box and assemble

the tile cutting machine as follows:

1. Slide the black rubber feet (T) over the

corners of the tile cutter. Slide a washer onto

the bolt and push this into the rubber foot.

Now slide a washer and a nut over the bolt on

the back and fasten this properly. Repeat this

for the other three corners.

2. Mount the fastening blocks (N) with the 2

tubes (M) onto the bottom plate (V) using the

4 bolts (O) and washers (P).

3. Screw the lever (H) onto the tube fastening (I).

4. Finally, mount the sash angle (U) onto the

bottom plate (V) using the knob (S) and

washer.

Assembly of the hollow square chisel

1. Place the hollow square chisel above the hole

in the bottom plate (V).

2. Make sure that the clamping plate (E) comes

under the 2 tubes and fasten this using the

socket head wrench supplied. The socket

head wrench is situated in the black fastening

plate (C).

3. It is important that the drill (G) and the knife

(F) are adjusted in such a way that they just

touch the bottom plate (V). This adjustment

can be done using the two nuts at the top of

the hollow square chisel. Then fasten these

nuts against each other.

3. How to cut and break tiles

1. Use a soft-tipped (carpenter’s) pencil to mark

off the cutting line.

2. Place the tile against the stop, the glazed

side facing upward. The pencil mark must be

directly below the blade.

3. Firmly hold the tile and cut several times (at

least 4) along the mark. After each cut, press

the lever more firmly.

4. Lift the lever when it has reached the front

edge of the tile and moved it backward.

5. Subsequently the break-off unit is lifted.

Repeat along the full width of the tile until the

notch is sufficiently deep.

The cutting movement results from

moving the lever from the back edge of

the tile towards its front, while lightly

pressing the lever.

Wall tiles

(single baked)

Lift the lever and position the break-off unit in the

middle of the tile. Press the lever down and the tile

will break.

Floor tiles

(double-baked):

Sometimes these much harder tiles cannot be cut

in two by means of the break-off unit (K) on the tile

cutting machine.

In these cases after making the notch the tile must

be broken in two by tapping the underside of the

tile with a light hammer along the full length of the

notch. This way the break line will spread through

the tile, and cause the tile to break in two along

the line. By means of the wing nut (Q) the angle of

the stop can be adjusted.

Making holes by means of the (hand) drill

1. Mount the drill attachment including the drill

over the centre of the hole in the base. It

is important that the drill and the blade are

adjusted in such a way that they just touch the

base. This adjustment can be made by means

of the upper two nuts.

Make sure to tighten the nuts after

adjustment.

Place the tile underneath the drill, the glazed

side facing upwards. By squeezing the

grips the tile can accurately be positioned

underneath the drill.

2. Moving the blade away from the centre will

enlarge the diameter of the hole. NB. The

scale on the blade holder indicates the radius

of the hole, i.e. the diameter is twice this

length.

3. By turning the handle clockwise, first a small

hole is drilled and subsequently a larger hole

of the correct size.

4. Do not press the handle while it is turned, this

may cause the tile to break.

5. Maintenance

The guide rods and the drill attachment do not •

require greasing.

After use remove any dust from the machine •

and store it in a dry place. If you expect the

machine will not be used for some time, it is

best to apply a thin coating of oil to the guide

rods and the lever.

Periodical maintenance of the tile cutting

machine prevents unnecessary

problems.

Replacing the knife

If the knife is worn, it can be replaced by a new

model.

This is done as follows:

Loosen the screw with which the knife is •

fastened and remove the knife from the

machine. Replace this knife by a new one and

fasten the screw again.

Guarantee

For the conditions of guarantee, please refer to

the separately provided guarantee card.

Specyfikacje produktu

Marka:	Ferm
Kategoria:	maszyna do cięcia
Model:	TCM1012

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Ferm TCM1012, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje maszyna do cięcia Ferm

Ferm TCM1012 Instrukcja

7 Sierpnia 2024

Instrukcje maszyna do cięcia

Najnowsze instrukcje dla maszyna do cięcia

Genius Nicer Dicer Quick Instrukcja

11 Stycznia 2025

Eldom Sliss KR350 Instrukcja

11 Stycznia 2025

RGV Desy AF 220 AM Instrukcja

10 Stycznia 2025

RGV Desy AF 275 F Instrukcja

10 Stycznia 2025

Royal Catering RCKS-3 Instrukcja

10 Stycznia 2025

Royal Catering RCKS-2 Instrukcja

10 Stycznia 2025

Ovela OVSAFSLCERA Instrukcja

5 Stycznia 2025

Royal Catering RCAM-250 Instrukcja

3 Stycznia 2025

Royal Catering RCES-215/12 Instrukcja

31 Grudnia 2025

CaterChef 537150 Instrukcja

31 Grudnia 2025