Instrukcja obsługi Fender Passport Event Series 2

Fender system hi-fi Passport Event Series 2

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Fender Passport Event Series 2 (44 stron) w kategorii system hi-fi. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/44
OWNER’S MANUAL | MANUAL DE INSTRUCCIONES
MODE D’EMPLOI | MANUAL DO PROPRIETÁRIO
MANUALE UTENTE | BEDIENUNGSHANDBUCH
INSTRUKCJA OBSŁUGI | NÁVOD K POUŽITÍ
NÁVOD NA POUŽITIE | UPORABNIŠKI PRIROČNIK
SYSTEM SETUP
Congratulations on purchasing a Fender® Passport Event Series 2
audio system—a self-contained portable audio system designed for
great sound anywhere. Carry Passport like a suitcase, and simply flip
open the cabinet-release latches to access two full-range speaker
cabinets, a powered mixer, and power and speaker cables.
Use Passport as a public address system or to amplify musical
instruments and vocals. Connect mobile devices for easy
accompaniment, including Bluetooth pairing. Passport's quick
and easy setup, its ability to cover large audiences and its simple
operation are the hallmarks of this innovative product. Its control
panel features mono mic/line channels and stereo line channels
with a variety of input jacks to provide superb connectivity
flexibility.
Register your Passport Event Series 2 online at start.fender.com.
ENGLISH
PASSPORT
®
EVENT SERIES 2
1
1. OPEN: Flip open cabinet latches on top of Passport
and detach speaker cabinets from powered
mixer section:
3. SPEAKER CABLE/POWER CORD STORAGE: Open storage
compartment on rear of mixer and remove power cord and
speaker cables:
2. PLACEMENT: For optimal results, elevate speaker cabinets on
Passport speaker stands or sturdy tables. Place the speakers far
apart to maximize stereo separation. Position mixer close by
for easy access to control panel:
4. Plug POWER CORD/SPEAKER CABLE CONNECTION:
speaker cables into left and right speaker jacks on back of
the mixer ( ), then connect corresponding upper right arrow
left and right speakers. Make sure power switch is off before
connecting power cord (included) into power inlet on back of
mixer (lower left arrow); plug other end into a grounded AC
power outlet:
ENGLISH
2
5. INPUTS: Connect microphones to channels 1 through 4;
connect other mono sound sources such as instruments to any
channel ( ). Use channel 6/7 inputs (large arrows smaller arrows) for
stereo/mono sound sources such as keyboards, other line-level
audio sources, and mobile devices:
7. POWER UP: Turn on all external equipment connected to
Passport first, then turn Passport on. Power LED will illuminate
green:
9. SETTING LEVELS: Connect a microphone or other sound
source and slowly turn up that channel's VOLUME control
(curved yellow arrow). LED above VOLUME control will
illuminate green when signal is present. LED will illuminate
yellow when signal is approaching clipping level; will
illuminate red when clipping (distortion) occurs. For best
performance, set channel VOLUME and TONE controls (curved
green arrows) so that LED is green and occasionally yellow.
If LED turns red, reduce VOLUME or TONE control settings.
If LED is still turning red after adjusting VOLUME and TONE
controls, press MIC/LINE button in (straight arrow):
Adjust each channel the same way. Use channel VOLUME
knobs to set relative loudness of each channel for overall
balance, then adjust MASTER VOLUME knob for overall mix
loudness. MASTER VOLUME has a SIGNAL LEVEL METER
just to the right; if meter illuminates red, decrease MASTER
VOLUME accordingly.
6. INITIAL VOLUME/REVERB: Turn MASTER VOLUME knob,
all channel VOLUME knobs and all REVERB knobs fully
counterclockwise to start:
8. SETTING MASTER VOLUME: Turn MASTER VOLUME up to
1/4 volume:
10. SETTING TONE/REVERB: Starting with each TONE
control (TREBLE, BASS) in the center-detented position (flat
equalization), set each TONE control to preference for best
clear and consistent sound coverage throughout the area.
REVERB controls (green arrows) are not center detented; set
these to preference:

Specyfikacje produktu

Marka: Fender
Kategoria: system hi-fi
Model: Passport Event Series 2

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Fender Passport Event Series 2, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje system hi-fi Fender

Fender

Fender Mustang GT200 Instrukcja

13 Września 2024
Fender

Fender Passport Event Series 2 Instrukcja

10 Września 2024
Fender

Fender Mustang GT40 Instrukcja

9 Września 2024

Instrukcje system hi-fi

Najnowsze instrukcje dla system hi-fi

Philips

Philips TAM3205M2 Instrukcja

14 Stycznia 2025
Philips

Philips TAM3505M2 Instrukcja

14 Stycznia 2025
OSD Audio

OSD Audio Nero Stream ARC Instrukcja

14 Stycznia 2025
Morel

Morel SUB-8X Instrukcja

14 Stycznia 2025
Morel

Morel BEAT-X Instrukcja

14 Stycznia 2025
Morel

Morel Sopran 634 Instrukcja

14 Stycznia 2025
Klipsch

Klipsch HD Theater 500 Instrukcja

14 Stycznia 2025
Lenco

Lenco MC-129 MP3 Instrukcja

13 Stycznia 2025
Terratec

Terratec HA-1 Charge Instrukcja

13 Stycznia 2025
Thomson

Thomson MIC400BT Instrukcja

12 Stycznia 2025