Instrukcja obsługi Fender Passport Conference Series 2

Fender Speaker Passport Conference Series 2

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Fender Passport Conference Series 2 (20 stron) w kategorii Speaker. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/20
OWNERS MANUAL
MANUAL DE INSTRUCCIONES
MODE D’EMPLOI
MANUAL DO PROPRIETÁRIO
SYSTEM SETUP
Congratulations on purchasing a Fender® Passport Conference
Series 2 audio system—a self-contained portable audio system
designed for great sound anywhere. Carry Passport like a
suitcase, and simply flip open the cabinet-release latches to
access two full-range speaker cabinets, a powered mixer, and
power and speaker cables.
Use Passport as a public address system or to amplify musical
instruments and vocals. Connect mobile devices for easy
accompaniment, including Bluetooth audio streaming.
Passport's quick and easy setup, its ability to cover large
audiences and its simple operation are the hallmarks of this
innovative product. Its control panel features mono mic/line
channels and stereo line channels with a variety of input jacks to
provide superb flexibility.
Register your Passport Conference Series 2 online at start.fender.com.
ENGLISH
PASSPORT
®
CONFERENCE SERIES 2
1
1. OPEN: Flip open cabinet latches on sides of Passport and
detach speaker cabinets from powered mixer section:
3. SPEAKER CABLE/POWER CORD STORAGE: Open storage
compartment on rear of mixer and remove power cord and
speaker cables:
2. PLACEMENT: For optimal results, elevate speaker cabinets on
Passport speaker stands or sturdy tables. Place the speakers far
apart to maximize stereo separation. Position mixer close by
for easy access to control panel:
4. Plug POWER CORD/SPEAKER CABLE CONNECTION:
speaker cables into left and right speaker jacks on back of
the mixer ( ), then connect corresponding left arrow at left
and right speakers. Make sure power switch is off before
connecting power cord (included) into power inlet on back
of mixer ( ); plug other end into a grounded AC arrow at right
power outlet:
ENGLISH
2
5. INPUTS: Connect microphones to channels 1, 2 and 3. Other
mono sound sources such as instruments can be connected
to any channel. Use channel 4/5 inputs for stereo/mono
sound sources such as keyboards, other line-level audio
sources, and mobile devices:
7. POWER UP: Turn on all external equipment connected to
Passport first, then turn Passport on. Power LED will illuminate
green:
9. SETTING LEVELS: Connect a microphone or other sound
source and slowly turn up that channel's VOLUME control. LED
above VOLUME control will illuminate green when signal is
present. LED will illuminate yellow when signal is approaching
clipping level; LED will illuminate red when clipping
(distortion) occurs. For best performance, set VOLUME and
TONE controls so that LED is green and occasionally yellow.
If LED turns red, reduce VOLUME or TONE control settings.
If LED is still turning red after adjusting VOLUME and TONE
controls, press MIC/LINE button in:
Set up each channel the same way. Use channel VOLUME
knobs to adjust relative loudness of each channel until
reaching preferred overall balance, then use MASTER VOLUME
to adjust overall mix loudness.
6. INITIAL VOLUME: Turn MASTER VOLUME knob and all
channel VOLUME knobs fully counterclockwise to start:
8. SETTING MASTER VOLUME: Turn MASTER VOLUME up to
1/4 volume:
10. SETTING TONE: Starting with each TONE control in the
center-detented position (flat equalization), set each TONE
control to preference for best clear and consistent sound
coverage throughout the area:

Specyfikacje produktu

Marka: Fender
Kategoria: Speaker
Model: Passport Conference Series 2

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Fender Passport Conference Series 2, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Speaker Fender

Instrukcje Speaker

Najnowsze instrukcje dla Speaker

Focal

Focal CMS 50 Instrukcja

19 Września 2024
OSD Audio

OSD Audio IW525 Instrukcja

19 Września 2024
Martin Logan

Martin Logan IC3 Instrukcja

19 Września 2024
OSD Audio

OSD Audio C1090VK Instrukcja

19 Września 2024
Tracer

Tracer Powertone BT Instrukcja

19 Września 2024
LogiLink

LogiLink SP0008 Instrukcja

19 Września 2024
OSD Audio

OSD Audio ICE810 Instrukcja

19 Września 2024
OSD Audio

OSD Audio ICE650 Instrukcja

19 Września 2024
Atlas Sound

Atlas Sound SMP-12 Instrukcja

19 Września 2024