Instrukcja obsługi Fantini Cosmi EV92

Fantini Cosmi kocioł centralnego ogrzewania EV92

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Fantini Cosmi EV92 (10 stron) w kategorii kocioł centralnego ogrzewania. Ta instrukcja była pomocna dla 9 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/10

FANTINI COSMI S.P.A. VIA DELL’OSIO 6

20090 CALEPPIO DI SETTALA (MI) ITALIA

Phone no. +39 02 95682.222 Fax no. +39 02 95307006

E-mail: export@fantinicosmi.it

Web: www.fantinicosmi.it

EV92 - SLAVE

DIGITAL INPUT

MODULE

in different modes and to be managed through daily

time programming.

DIGITAL INPUT OPERATION PROGRAMS

All the eight inputs can be congured with the sta-

tus showing when failure or signalling is activated:

OPENING or CLOSING, and the operation program:

FAILURE ON, FAILURE OFF and TIMED FAILURE.

When selecting the Timed Failure program, the set

time programming will be taken into account.

TIME PROGRAMMING

When selecting the TIMED FAILURE program, each

digital input can be activated in three preset time

bands equal for each day of the week.

Input is just monitored in the period falling between

the three ON and the three OFF times. If one of the

three time bands is excluded (to do this press the

PLUS and MINUS keys of the remote keyboard to

highlight the dashes --,--) input will not be monitored.

N.B. When all the three time bands are excluded,

the digital input is monitored continuously as if the

ALWAYS ON program is set.

USE

The EV92 module is suitable to be used on all plants

where it is necessary to acquire and to manage

switching from one to eight failure or operation sig-

nalling contacts. The EV92 module is mainly suited

for industrial plants, water control systems, green-

houses, heating or air-conditioning plants, etc..

OPERATION

The EV92 module features eight digital optoisolated

inputs, each of which can be congured to operate

DESIGN CHARACTERISTICS

6-module DIN container; removable terminal boards

facilitate replacement.

Digital input signalling led

BUTTON to reset

factory settings

INSTALLATION

INSTALLING THE CONTROL UNIT

Mount the device onto the DIN rail inside a panel in

order to provide suitable protection. Removable ter-

minal boards facilitate wiring and replacement. Con-

necting leads to the control unit must have a section

of at least 1 mm2 and a length of 1000 metres.

CONNECTION TO THE FANBUS

Connect the EV92 control unit to the Master EV90

through the FANBUS. Bear in mind that the bus has

low voltage and it is not polarised, terminals can

therefore be inverted with each other without causing

malfunction.

CONTROL UNIT ADDRESS

The control units must be addressed through the

terminal board to work properly. The address of the

EV92 unit is made up of a high part that corresponds

to number “3”, and a low part that may take on a value

between “0” and “7”. The MASTER unit starts a pro-

gressive search of SLAVES EV92 from address “30”

and it will stop if it gets no reply. It is therefore neces-

sary that connected slaves have different consecutive

addresses starting from address “30”.

The diagrams below show how to set the low part of

the address through terminal board ‘A’ :

ADDRESS “30” ADDRESS “31” ADDRESS “32” ADDRESS “33”

ADDRESS “37”ADDRESS “36”ADDRESS “35”ADDRESS “34”

EV92 WIRING DIAGRAM

TO FANBUS

EV90

ALARM 5

ALARM 1

ALARM 2

ALARM 3

ALARM 4

ALARM 6

ALARM 7

ALARM 8

COMMON ALARM 7-8

COMMON ALARM 5-6

COMMON ALARM L1

COMMON ALARM L2

COMMON ALARM 3

COMMON ALARM 4

POWER SUPPLY

230V

N.B. ALL INPUTS MUST BE VOLTAGE

FREE CONTACTS

A1 A2 A4 COM

ADDRESS

SETTINGS AND ADJUSTMENTS

FACTORY SETTINGS

The EV92 leaves the factory with all parameters set

for standard operation. Should it be necessary to

reset factory parameters (default data), turn off the

power supply, then turn it on again while pressing the

key on the front panel. All data entered will be lost,

whereas factory parameters will be reset.

INITIALISING THE DEVICE

Each time the slave module is powered, the leds set

on the front panel will start ashing simultaneously

until the Master EV90 starts communicating with the

relevant device by selecting its address or transmit-

ting time data through the bus. As from this moment

the salve module will start working regularly.

SETTINGS AND ADJUSTMENTS

To modify EV92 data it is necessary to use the Master

EV90 that will act like the display and the remote key-

board of the EV92. Data is entered through special

menus provided for the purpose which may contain

a number of submenus. Press the “PLUS” “MINUS”

“FORWARD” “BACK” “UP” and “DOWN” keys to

scroll the different menus and to modify parameters.

Specyfikacje produktu

Marka:	Fantini Cosmi
Kategoria:	kocioł centralnego ogrzewania
Model:	EV92

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Fantini Cosmi EV92, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje kocioł centralnego ogrzewania Fantini Cosmi

Fantini Cosmi EV85 Instrukcja

24 Września 2024

Fantini Cosmi EV91C Instrukcja

5 Września 2024

Fantini Cosmi EV90 Instrukcja

1 Września 2024

Fantini Cosmi EV87 Instrukcja

31 Sierpnia 2024

Fantini Cosmi EV92 Instrukcja

25 Sierpnia 2024

Fantini Cosmi EV91D Instrukcja

19 Sierpnia 2024

Fantini Cosmi EV91A Instrukcja

14 Sierpnia 2024

Fantini Cosmi EV91B Instrukcja

13 Sierpnia 2024

Fantini Cosmi EV80 Instrukcja

13 Sierpnia 2024

Fantini Cosmi EV02F Instrukcja

7 Sierpnia 2024

Instrukcje kocioł centralnego ogrzewania

Najnowsze instrukcje dla kocioł centralnego ogrzewania

ACV E-Tech P 201 Instrukcja

15 Stycznia 2025

Buderus Logamax plus GB192 i Instrukcja

13 Stycznia 2025

Intergas HRE 24-18 Instrukcja

13 Stycznia 2025

Intergas HRE 36-30 Instrukcja

13 Stycznia 2025

Intergas H22VRTW Instrukcja

13 Stycznia 2025

Intergas HRE 28-24 Instrukcja

13 Stycznia 2025

Baxi Neta-tec Combi 28 GA Instrukcja

11 Stycznia 2025

Baxi Platinum Compact Instrukcja

28 Grudnia 2024

Baxi Platinum iPlus Instrukcja

28 Grudnia 2024

Kospel EKD.M3 Instrukcja

27 Grudnia 2024