Instrukcja obsługi Extech MO57

Extech Niesklasyfikowane MO57

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Extech MO57 (2 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
MO57- - /17 en GB_V1.0 7
1
USER MANUAL
Pinless Moisture Meter
Model 57MO
Introduction
Thank you for selecting 57 employs a the Extech MO57 MPinless oisture Meter. The MO non-
destructive spherical sensor that safely glides over surfaces to measure the relative moisture in
wood and other building materials ( board, sheet rock, cardboard, pwall laster, concrete, and mortar)
at any angle to a depth of 10.2cm (4”).
To indicate moisture MO57 provides a digital reading audible tones and ‘moisture droplevel the , , let’
icons. Audi ble tones (eight levels of intensity) and droplet icons (1, 2, or 3) increase in proportion to
increased moisture. Additional features include Auto Power OFF and Display Lock (hold).
This meter ships fully tested and calibrated and, with proper use, will provide years of reliable
service. Please visit our website ( ) to check for the latest version of this User Guide, www.extech.com
Product Updates, and Customer Support.
Measurement Considerations
To measure moisture, the sensor emits and senses low- -power electro magnetic signals. The
displayed reading in percent is an average of the moisture content measured over the measurement
surface area and the maximum depth of penetration . .0(10 2cm [4 ”]). Moisture that is closer to the
surface has a greater effect on the displayed average than the moisture nearer to the maximum
depth of penetration.
Placing the sensor on a surface whose thickness is less than the maximum depth of penetration may
result in unreliable moisture readings; in these cases, you can stack material on top of the measured
surface to increase the thickness.
The MO57 also produces audible tones and ‘moisture droplet’ display icons to indicate moisture
level. The audible tone rate and number of droplets increase as the moisture level increases. When
measuring, keep hand stationary on the meter while holding and moving the meter, as hand
movement can affect the readings.
Meter Description
1. LCD Display
2. Power button
3. Display Lock/Beeper button
4. Material Select button
5. Sensor
Note Batt: ery compartment on rear of meter
Display Description
1. Droplet icons (1 for low moisture, 2 for medium, and 3 for high)
2. Wood mode
3. Building Material mode
4. Beeper active icon
5. Moisture reading
6. Percent moisture unit (relative)
7. Display Lock mode
8. Battery status icon
Button Descriptions
Symbol
Button name
Description
Power - ON OFF Long press to switch the meter ON or OFF
/
Material Select (wood/building
materials)
Short press to toggle material groups
/ Display Lock / Beeper control
Short press locks/unlocks reading on the display
Long press toggles the Beeper ON/OFF
Operation
Powering the Meter
1. . Long press the power button to turn the meter ON/OFF
2. The meter emits audible tones and calibration upon start Keep the -performs a self -up.
measurement sensor at least 8 to 10 cm (3 to 4”) from hands and during calibrationobjects .
The calibration reading must not exceed 0.5. If so, re calibrate ensuring that hands or other -
objects are clear of the sensor. enever Note: Calibrate the meter wh moving from one
measurement area to another.
3. If the battery symbol appears or if the meter does not switch ON, . replace the battery
1
23
4
5
MO57- - /17 en GB_V1.0 7
2
Auto Power OFF
The meter will automatically power OFF if the reading stays 0% for 3 minutes. If the meter detects
readings, other than 0%, it will not automatically power OFF.
Display (Hold) Lock
Short press the Display Lock button to freeze the displayed reading. The icon is visible on
the display when Display Lock is active. Press again to return to the normal operating mode.
Beeper ON/OFF
The beeper defaults to ON. To switch the beeper OFF, long press the Display Lock/Audible Beeper
button . When the beeper is active, the audio display icon will be visible.
Pinless Moisture Measurements
1. ( Short press the Material Select button ) to toggle the Wood and Building Material
modes of operation. The displayed icon s indicate the selected mode.
2. To take a measurement, hold the meter and position the sensor directly touching so that it is
the surface under test (at any angle). The meter can sense moisture to a depth .2cm ( of 10 4” ).
NOTE: The position of your hand can affect the reading. Do not move or reposition the hand
that holds the meter while taking measurements or when the unit.powering
3. s Observe the displayed relative reading , view the displayed moisture droplet icon(s) (more
drops indicate higher moisture levels), and listen for the audible beeping (faster beeping
indicates higher moisture; there are eight intensity levels). As discussed in the Measurement
Considerations section, the displayed reading is an average of the moisture measured over the
tested surface area to the maximum penetration depth.
4. Long press the power button to power OFF the meter.
Relative Moisture Reading Reference Table
BUIL DING MATERIAL (%)
TOTAL RANGE >
0.1~99.9
LOW
0.1~9.9
10.0~16.9
MEDIUM
17.0~23.9
24.0~29.9
30.0~39.9
HIGH
40.0~59.9
60.0~69.9
70.0~99.9
Maintenance
Battery Replacement
When the status icon appears empty or flashingbattery , replace the battery.
1. Remove the battery cover by pushing the compartment latch (bottom, back of meter) .
2. . Replace the 9V battery observing correct polarity
3. . Replace the battery cover securely
4. Dispose of battery responsibly and within applicable legal regulations.
Never dispose of used batteries or rechargeable batteries in household waste.
As consumers, users are legally required to take used batteries to appropriate
collection sites, the retail store where the batteries were purchased, or wherever
batteries are sold.
Disposal: Do not dispose of this instrument in household waste. The user is obligated to take
end- -of life devices to a designated collection point for the disposal of electrical and electronic
equipment.
Care and Cleaning
• Store the meter in an environmentally stable, dust ronment, out of direct sunlight.-free envi
• Remove the battery from the instrument if the meter is to be stored for long periods or if
the battery power symbol appears or flashing on the display.empty ( )
• To clean the meter case, wipe with a damp cloth, do not use solvents or abrasives.
Specifications
Display -LCD with multi function indicators
Sensor Type Pinless spherical sensor
Me destructiveasurement Type Non- , electro- magnetic sensing
Measurement I s) and audible tone with ndication Digital, Moisture Droplet icons (1, 2, or 3 droplet
eight levels of intensity indicating low to high moisture readings
Measurement angeR s:
Wood: Low: 0.1% to 16.9%; Medium: 17.0% to 39.9%; High: 40.0 to 99.9%
Building Materials: Low: 0.1% to 16.9%; Medium: 17.0% to 39.9%; High: 40.0 to 99.9%
Measurement depth Sensor detects to a depth of 10.2cm (4”)
Resolution 0.1%
Accuracy Relative readings only
Auto Power OFF three (3) After approx. minutes with 0% display reading.
Power supply One (1) 9V Battery; Consumption: < 40mA
Low Battery indication < 7.5VDC, approximately
Low Battery APO < 5.5VDC; APO will occur in 20 seconds, approximately
Operating conditions 5 ~ 45oC (41 ~ 113oF); 80%RH max.
Storage conditions 0 ~ 50oC (32 ~ 122oF); 85%RH max.
Dimensions x " 210 x 70 33mm (8.3 x 2.8 x 1.3 )
Weight 155 5.5 g ( oz.) without battery
Copyright © 2017 FLIR Systems, Inc.
All rights reserved including the right of reproduction in whole or in part in any form
www.extech.com

Specyfikacje produktu

Marka: Extech
Kategoria: Niesklasyfikowane
Model: MO57

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Extech MO57, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Extech

Extech

Extech 380396 Instrukcja

3 Października 2024
Extech

Extech HDV600 Instrukcja

3 Października 2024
Extech

Extech 380395 Instrukcja

3 Października 2024
Extech

Extech HDV540 Instrukcja

29 Września 2024
Extech

Extech 380260 Instrukcja

29 Września 2024
Extech

Extech CO220 Instrukcja

27 Września 2024
Extech

Extech MO57 Instrukcja

19 Września 2024
Extech

Extech DCP36 Instrukcja

18 Września 2024
Extech

Extech HD750 Instrukcja

13 Września 2024
Extech

Extech CO100 Instrukcja

11 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024