Instrukcja obsługi EverFocus EM900FP4

EverFocus Kamera monitorująca EM900FP4

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla EverFocus EM900FP4 (15 stron) w kategorii Kamera monitorująca. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/15

EM900F eZ.HD Series

1080p Full High Definition

Micro Mini Metal Camera

User’s Manual

Release Date: February 6 201

Precautions

1. Do not install the camera near electric or magnetic fields. Install the camera away from

TV/radio transmitters, magnets, electric motors, transformers and audio speakers since the

electromagnetic fields generated from these devices may distort the video image or

otherwise interfere with camera operation.

2. Never disassemble the camera beyond the recommendations in this manual nor introduce

materials other than those recommended herein. Improper disassembly or introduction of

corrosive materials may result in equipment failure or other damage.

3. Try to avoid facing the camera toward the sun. In some circumstances, direct sunlight may

cause permanent damage to the sensor and/or internal circuits, as well as creating

unbalanced illumination beyond the capability of the camera to compensate.

4. Keep the power cable away from water and other liquids and never touch the power cord

with wet hands. Touching a wet power cord with your hands or touching the power cord

with wet hands may result in electric shock.

5. Never install the camera in areas exposed to oil, gas or solvents. Oil, gas or solvents may

result in equipment failure, electric shock or, in extreme cases, fire.

6. Cleaning. For cameras with interchangeable lenses, do not touch the surface of the sensor

directly with the hands. Use lens tissue or a cotton tipped applicator and ethanol to clean

the sensor and the camera lens. Use a damp soft cloth to remove dirt from the camera any

body. Please do not use complex solvents, corrosive or abrasive agents for cleaning of any

part of the camera.

7. Do not operate the camera beyond the specified temperature, humidity or power source

ratings. This camera is suitable for indoor operation only. Use the camera at temperatures

within - 0 210°C~5 °C (14°F~11 °F) and humidity less than 80%; this device is not rated as

submersible. The input power source is 12VDC. Be sure to connect the proper + / - polarity

and voltage, as incorrect polarity or too high a voltage will likely cause the camera to fail,

and such damage is not covered by the warranty.

8. Mounting. Use care in selecting a solid mounting surface which will support the weight of

the camera plus any wind, snow, ice or other loading, and securely attach the camera to the

mounting surface using screws and anchors which will properly support the camera. If

necessary (e.g. when mounting to drop ceilings) use a safety wire to provide additional

support for the camera.

Safety Notice

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates uses and

can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one of the

following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

Specyfikacje produktu

Marka:	EverFocus
Kategoria:	Kamera monitorująca
Model:	EM900FP4

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z EverFocus EM900FP4, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Kamera monitorująca EverFocus

EverFocus EQ350 Instrukcja

23 Września 2024

EverFocus EZN7221 Instrukcja

22 Września 2024

EverFocus ED200/N-3W Instrukcja

22 Września 2024

EverFocus EHN3261 Instrukcja

22 Września 2024

EverFocus EBD935 Instrukcja

22 Września 2024

EverFocus EQ250A/N Instrukcja

22 Września 2024

EverFocus EBD430 Instrukcja

22 Września 2024

EverFocus EM900FP4 Instrukcja

22 Września 2024

EverFocus EIVP-KBU-IV-V0004 Instrukcja

22 Września 2024

EverFocus EDN468ME Instrukcja

22 Września 2024

Instrukcje Kamera monitorująca

Najnowsze instrukcje dla Kamera monitorująca

Trebs CCD-401C Instrukcja

15 Października 2024

Hikvision DS-2CE56D5T-AIRZ Instrukcja

15 Października 2024

D-Link DCS-7510 Instrukcja

15 Października 2024

Ubiquiti Networks UniFi Video UVC-G3-AF Instrukcja

14 Października 2024

Hikvision DS-2TD2137-7/VP Instrukcja

13 Października 2024

Alecto DVC-215IP Instrukcja

13 Października 2024

Hikvision DS-2DE7A245IX-AE/S1 Instrukcja

13 Października 2024

Hikvision DS-2TD2166-15/V1 Instrukcja

13 Października 2024

Hikvision DS-2CD2325FWD-I Instrukcja

13 Października 2024

Hikvision DS-2CD2323G2-IU Instrukcja

12 Października 2024