Instrukcja obsługi EverFocus EBD430

EverFocus Kamera monitorująca EBD430

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla EverFocus EBD430 (15 stron) w kategorii Kamera monitorująca. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/15

EverFocus

Operation Instructions

3”

”

-A

Operation Instruction

Please read this manual first for correct installation and operation. This manual should be retained for

future reference. The information in this manual was current when published. The manufacturer

reserves the right to revise and improve its products. All specifications are therefore subject to change

without notice.

by any means without written permission of the EverFocus Electronics Corporation.

Precautions

1. Do not place any object on top of the cover.

2. Be careful when handling the camera, to prevent any damage do not drop it or subject it

to strong shock or vibration. Do not disassemble it or attach it on an unstable base.

3. Install the camera away from TV or radio transmitters, magnets, electric motors,

transformers and audio speakers because the magnetic fields generated from these devices

may distort the video image.

4. Install the camera away from heaters, or other heat generating devices as the high

temperature could cause deformation, discoloration or other damage to the camera.

Install the camera at where the temperature range will stay between -40°C to 50°C (-40°F

to 122°F).

5. Never aim the camera at the sun or other extremely bright objects whether it is in use or

not.

6. Do not touch the surface of CCD sensor directly with your ﬁngers. Use a soft cloth to

remove any dirt from the camera body. If necessary, use lens tissue or a cotton tipped

applicator and ethanol to clean the CCD sensor and the camera lens. When the camera

is not in use, protect the surfaces covering the lens and IR emitters.

7. rating instructions should be adhered to. All warnings on the product and in the ope

8. Do not use attachments not recommended by the camera manufacturer as they may cause

hazards.

9. Do not allow anything to rest on the power cord. Do not locate this device where the cord

may be abraded or may cause a hazard by persons walking on it.

10. Do not overload wall outlets and extension cords as this can result in fire or electric

shock.

11. Never push objects of any kind into his appliance through cabinet slots as they may touch

dangerous voltage points or short out parts that could result in fire, electric shock or

damage to the camera.

12. Refer all work related to the installation of this product to qualified service personnel or

system installers.

Federal Communication Commission Interference

Statement

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible

for compliance could void the user's authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired operation.

Note: There is a screw located in the focus ring and the zoom ring for

waterproofing purposes only. These are NOT set screws!! Please don’t loosen or

remove them.

Specyfikacje produktu

Marka:	EverFocus
Kategoria:	Kamera monitorująca
Model:	EBD430

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z EverFocus EBD430, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Kamera monitorująca EverFocus

EverFocus EQ350 Instrukcja

23 Września 2024

EverFocus EZN7221 Instrukcja

22 Września 2024

EverFocus ED200/N-3W Instrukcja

22 Września 2024

EverFocus EHN3261 Instrukcja

22 Września 2024

EverFocus EBD935 Instrukcja

22 Września 2024

EverFocus EQ250A/N Instrukcja

22 Września 2024

EverFocus EBD430 Instrukcja

22 Września 2024

EverFocus EM900FP4 Instrukcja

22 Września 2024

EverFocus EIVP-KBU-IV-V0004 Instrukcja

22 Września 2024

EverFocus EDN468ME Instrukcja

22 Września 2024

Instrukcje Kamera monitorująca

Najnowsze instrukcje dla Kamera monitorująca

Trebs CCD-401C Instrukcja

15 Października 2024

Hikvision DS-2CE56D5T-AIRZ Instrukcja

15 Października 2024

D-Link DCS-7510 Instrukcja

15 Października 2024

Ubiquiti Networks UniFi Video UVC-G3-AF Instrukcja

14 Października 2024

Hikvision DS-2TD2137-7/VP Instrukcja

13 Października 2024

Alecto DVC-215IP Instrukcja

13 Października 2024

Hikvision DS-2DE7A245IX-AE/S1 Instrukcja

13 Października 2024

Hikvision DS-2TD2166-15/V1 Instrukcja

13 Października 2024

Hikvision DS-2CD2325FWD-I Instrukcja

13 Października 2024

Hikvision DS-2CD2323G2-IU Instrukcja

12 Października 2024