Instrukcja obsługi EverFocus ED930

EverFocus Kamera monitorująca ED930

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla EverFocus ED930 (17 stron) w kategorii Kamera monitorująca. Ta instrukcja była pomocna dla 10 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/17

ED910 & ED930

720p Analog High Denion

True Day/Night Indoor Dome Camera

User’s Manual

Release Date: Nov., 2014

Precauons

1. Do not install the camera near electric or magnec elds. Install the camera away from

TV/radio transmitters, magnets, electric motors, transformers and audio speakers since the

electromagnetic elds generated from these devices may distort the video image or

otherwise interfere with camera operation.

2. Never disassemble the camera beyond the recommendaons in this manual nor introduce

materials other than those recommended herein. Improper disassembly or introducon of

corrosive materials may result in equipment failure or other damage.

3. Try to avoid facing the camera toward the sun. In some circumstances, direct sunlight may

cause permanent damage to the sensor and/or internal circuits, as well as creang

unbalanced illuminaon beyond the capability of the camera to compensate.

4. Keep the power cable away from water and other liquids and never touch the power cord

with wet hands. Touching a wet power cord with your hands or touching the power cord

with wet hands may result in electric shock.

5. Never install the camera in areas exposed to oil, gas or solvents. Oil, gas or solvents may

result in equipment failure, electric shock or, in extreme cases, re.

6. Cleaning. For cameras with interchangeable lenses, do not touch the surface of the sensor

directly with the hands. Use lens ssue or a coon pped applicator and ethanol to clean

the sensor and the camera lens. Use a damp soft cloth to remove any dirt from the camera

body. Please do not use complex solvents, corrosive or abrasive agents for cleaning of any

part of the camera.

7. Do not operate the camera beyond the specied temperature, humidity or power source

rangs. This camera is suitable for indoor operaon only. Use the camera at temperatures

within -10°C~50°C (14°F~1 °F) and humidity between 20%~ 80%; this device is not rated as 22

submersible. The input power source is 12VDC or 24VAC. Be sure to connect the proper + / -

polarity and voltage, as incorrect polarity or too high a voltage will likely cause the camera

to fail, and such damage is not covered by the warranty.

8. Mounng. Use care in selecng a solid mounting surface which will support the weight of

the camera plus any wind, snow, ice or other loading, and securely aach the camera to the

mounng surface using screws and anchors which will properly support the camera. If

necessary (e.g. when mounng to drop ceilings) use a safety wire to provide addional

support for the camera.

Safety Noce

Federal Communicaon Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protecon

against harmful interference in a residenal installaon. This equipment generates uses and

can radiate radio frequency energy and, if not installed and used in accordance with the

instrucons, may cause harmful interference to radio communicaons. However, there is no

guarantee that interference will not occur in a parcular installaon. If this equipment does

cause harmful interference to radio or television recepon, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one of the

following measures:

- Reorient or relocate the receiving antenna.

- Increase the separaon between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC Cauon: Any changes or modications not expressly approved by the party responsible for

compliance could void the user's authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operaon is subject to the following two

condions: (1) This device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operaon.

Specyfikacje produktu

Marka:	EverFocus
Kategoria:	Kamera monitorująca
Model:	ED930

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z EverFocus ED930, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Kamera monitorująca EverFocus

EverFocus EQ350 Instrukcja

23 Września 2024

EverFocus EZN7221 Instrukcja

22 Września 2024

EverFocus ED200/N-3W Instrukcja

22 Września 2024

EverFocus EHN3261 Instrukcja

22 Września 2024

EverFocus EBD935 Instrukcja

22 Września 2024

EverFocus EQ250A/N Instrukcja

22 Września 2024

EverFocus EBD430 Instrukcja

22 Września 2024

EverFocus EM900FP4 Instrukcja

22 Września 2024

EverFocus EIVP-KBU-IV-V0004 Instrukcja

22 Września 2024

EverFocus EDN468ME Instrukcja

22 Września 2024

Instrukcje Kamera monitorująca

Najnowsze instrukcje dla Kamera monitorująca

Dahua Technology Pro IPC-HDPW5442G-Z Instrukcja

15 Stycznia 2025

Toshiba IKS-WR7412 Instrukcja

13 Stycznia 2025

AVerMedia FC1320-P Instrukcja

13 Stycznia 2025

Digitus OptiMax DN-16037 Instrukcja

13 Stycznia 2025

Hikvision DS-2CE59U1T-AVPIT3ZF Instrukcja

12 Stycznia 2025

Hikvision IDS-2CD7526G0-IZHSY Instrukcja

12 Stycznia 2025

Hikvision DS-2CD2163G0-I(S) Instrukcja

12 Stycznia 2025

Hikvision DS-2CD2H83G1-IZS Instrukcja

12 Stycznia 2025

Speco Technologies O5LB1 Instrukcja

12 Stycznia 2025

ZKTeco AntarVis 2.0 Instrukcja

12 Stycznia 2025