Instrukcja obsługi Eurolite LVH-5

Eurolite Kontroler LVH-5

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Eurolite LVH-5 (4 stron) w kategorii Kontroler. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/4
www.eurolite.de
USER MANUAL
BEDIENUNGSANLEITUNG
LVH-5
VIDEO SWITCH
© Copyright
Nachdruck verboten!
Reproduction prohibited!
1 2 3 4
HOLD
RATE
MIN MAX
LVH-5
AUT OMATIC AUDIO V IDEO S WIT CH
LVH-5 VIDEO SWITCH
1234
CO NT RO L OUT PUT S
DC 12 -24V
LVH-5
AUTOMAT IC AUDIO VID EO SWIT C H
RESET
VIDEO OUT
INPUT INPUT
LOOP OUT LOOP OUT
12
34
INPUT INPUT
LOOP OUT LOOP OUT
Signal source
Signalquelle
75 terminator plugW
75 AbschlusswiederstandW
75 signal outputW
75 SignalausgangW
Signal source
Signalquelle
Durchschleifsignal zu
other 75 video inputW
Feed-through signal to
anderem 75 VideoeingangW
12-24 V DC
optional jumpers
optionale Jumper
2 sources/Quellen
3 sources/Quellen
Input and output video signals must be 75 terminated.
W
Videoein- und ausgangssignale benötigen 75 Abschlüsse.
W
LVH-5 VIDEO SWITCH
MANUAL SWITCH 4:1
The LVH-5 was designed to switch video signals from up to four sources to one output.
Switching is made automatically and is indicated by control LEDs. The switching time is
adjustable. Each channel features a manual override button to stop the sequencing mode.
Each input is provided with a parallel output for feed-through of the input signal. The open
collector outputs allow for controlling other units. Power connections are made using block
terminals. The unit is compatible with NTSC and PAL systems.
SAFETY INSTRUCTIONS
• Before your initial start-up, please make sure that there are no transport damages. Should
there be any, do not take the device into operation and immediately consult your dealer.
• Operate the device only after having familiarized with its functions. Do not permit operation
by persons not qualified for operating the device.
• Protect the device against humidity and heat. Keep away from heaters and other
heating sources!
• We recommend a frequent cleaning of the device. Disconnect from mains first. Use
a soft lint-free and moistened cloth. Never use alcohol or solvents!
• There are no serviceable parts inside the device. Maintenance and service operations are
only to be carried out by authorized dealers.
• Damage, caused by manual modifications on the device are not subject to warranty. If the
device is used for other purposes than originally intended or if it is not correctly connected,
the product may suffer damages and the guarantee becomes void.
• This product is allowed to be operated with 12-24 V DC. This device falls under protection
class 3 and was designed for indoor use only.
OPERATION
Prior to connecting switch off all units and do not turn them on again until you have made all
necessary connections.
1 Connect each signal source which is to be switched via a 75 coaxial cable with BNC
plugs to the jacks INPUT1-4.
2 The input signal fed through is available at the outputs LOOP OUT. These outputs allow to
connect the line inputs of further LVH-5 or different units. If 75 termination of the input
signal is required, plug the supplied terminator onto the LOOP OUT jack. The output
video signal is 75 back-terminated to provide unity gain (0 dB) into a 75 terminated
input.
3 Connect the unit to which the video signal is to be switched via a 75 coaxial cable with
BNC plugs to the jack VIDEO OUT.
4 If fewer than four signal sources are being used, a jumper may be installed to program the
LVH-5 to use two or three sources. With two signal sources, connect the jumper to the
terminals RESET and 3; with three signal sources connect it to the terminals RESET and 4.
5 The open collector outputs allow to control other units. For this purpose, connect the
external unit's relay contacts to the terminals REMOTE CONTROL1-4.
6 To power the unit 12-24 V DC are required. For this purpose, connect a power source (e.g.
power supply unit, battery) to the terminals DC 12-24. Always observe the correct polarity.
Connect the marked core to the left contact "+".
7 When power is first applied to the LVH-5, it sequences between the video inputs at the
interval set on the control RATE. An LED indicator above each selector button shows
which video source is active. To stop the sequencing, press the desired selector button 1-4.
Then the output displays that input. While the unit is holding at that signal source, the
HOLD LED flashes. Press the selector button once again to resume the sequencing or
switch to another signal source with the selector buttons while in hold mode.
TECHNICAL SPECIFICATIONS
Power supply: ..................12-24 V DC, 110 mA
4x video inputs: ................5 k (bridged), 75 (terminated), BNC
5x outputs: .......................75 , BNC (4 feed-through outputs, 1 amplified output)
4x open collector outputs:.50 mA, block terminals
Dimensions (LxWxH): ......146 x 78 x 42 mm
Weight: ............................390 g
W
W
W W
W
W W
W
Please note: Every information is subject to change without prior notice. 20.01.2009 ©

Specyfikacje produktu

Marka: Eurolite
Kategoria: Kontroler
Model: LVH-5

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Eurolite LVH-5, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Kontroler Eurolite

Eurolite

Eurolite LVH-1 Instrukcja

16 Września 2024
Eurolite

Eurolite DMX Operator 192 Instrukcja

13 Września 2024
Eurolite

Eurolite LVH-5 Instrukcja

12 Września 2024
Eurolite

Eurolite LVH-4 Instrukcja

12 Września 2024
Eurolite

Eurolite LVH-3 Instrukcja

11 Września 2024
Eurolite

Eurolite LVH-8 Instrukcja

10 Września 2024
Eurolite

Eurolite VSD-108 Instrukcja

10 Września 2024
Eurolite

Eurolite DMX Scene Setter 24/48 Instrukcja

10 Września 2024
Eurolite

Eurolite AVS-402 Instrukcja

8 Września 2024
Eurolite

Eurolite DPMX-1216 Instrukcja

7 Września 2024

Instrukcje Kontroler

Najnowsze instrukcje dla Kontroler

DJI

DJI Motion Controller Instrukcja

14 Stycznia 2025
8BitDo

8BitDo Ultimate C Wired Controller Xbox Instrukcja

11 Stycznia 2025
Balam Rush

Balam Rush Kontrol React G575 Instrukcja

11 Stycznia 2025
PCE Instruments

PCE Instruments PCE-RE100P Instrukcja

10 Stycznia 2025
PCE Instruments

PCE Instruments PCE-RE21R Instrukcja

10 Stycznia 2025
Sonance

Sonance VC30R Instrukcja

8 Stycznia 2025
BeamZ

BeamZ WTR10-5 Instrukcja

5 Stycznia 2025
Audibax

Audibax MC1000 Instrukcja

5 Stycznia 2025
Somfy

Somfy Keypad 2 RTS Instrukcja

1 Stycznia 2025
Somfy

Somfy Keypop RTS Instrukcja

1 Stycznia 2025