Instrukcja obsługi Emos M0230
Emos
Multimeter
M0230
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Emos M0230 (75 stron) w kategorii Multimeter. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/75
2
1
2
4
5
6
1
3
8
7
MAX
INPUTCOM
FUSED
MAX
FUSED
500mA
10A
10SEC
EACH 15MIN
MAX
600V
A
H
Select
OFF
200
10
200m
1.5V
9V
200
2
20
2M
200k
20k
2k
600
200
600
TEMP
BATT
V
V
A
EN61010- 1
CAT III 600V
°C°F
TRUE RMS
9
3
GB | Digital Multimeter
Read this instruction manual thoroughly before you begin using
the M0230. It contains particularly important passages concerning
occupational safety principles when using the device. Such passages
are highlighted. Reading the manual will prevent potential injury by
electric current or damage to the device.
The multimeter was designed in accordance with standard EN
61010-1, applying to electronic measuring instruments belonging
to category CAT III 600 V, pollution degree 2. CAT III is intended for
measuring circuits powered by xed wiring installations, such as
relays, sockets, distribution boxes, feeder lines and short branching
circuits and lighting systems in large buildings.
Do not use the multimeter to measure ranges that fall into the
category IV!
Warning:
Use the M0230 multimeter only in the manner specied below. Other
uses may cause damage to the device or endanger your health.
Comply with the following instructions:
• Before measuring resistance, diodes or current, disconnect the
circuits from the power supply and discharge any high-voltage
capacitors. Use a function appropriate for the given measure-
ment. Before changing the range (or switching functions) dis-
connect the conductors from the circuit that is being measured.
• Make sure the device is undamaged before you begin using the
multimeter. If you nd obvious signs of damage on the body of
the device, do not make any measurements! Check that the
surface of the multimeter does not have scratches and that the
side joints are not coming apart.
• Also check the insulation on the measuring probes. Damaged
insulation may result in injury by electric current. Do not use
damaged measuring probes!
• Do not measure voltages above 600 V! If you intend to measure
current, check the multimeter‘s fuse and turn o the power
supply to the circuit before you connect the multimeter. Before
Specyfikacje produktu
Marka: | Emos |
Kategoria: | Multimeter |
Model: | M0230 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Emos M0230, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Multimeter Emos
7 Września 2024
30 Sierpnia 2024
29 Sierpnia 2024
7 Sierpnia 2024
2 Lipca 2024
Instrukcje Multimeter
- Multimeter PeakTech
- Multimeter Voltcraft
- Multimeter Milwaukee
- Multimeter GW Instek
- Multimeter Stanley
- Multimeter TFA
- Multimeter Chauvin Arnoux
- Multimeter Gembird
- Multimeter Uni-T
- Multimeter Owon
- Multimeter Velleman
- Multimeter Gossen Metrawatt
- Multimeter Fluke
- Multimeter BENNING
- Multimeter Metrix
- Multimeter Ferm
- Multimeter Extech
- Multimeter Testboy
- Multimeter Kyoritsu
- Multimeter Powerfix
- Multimeter Monacor
- Multimeter Laserliner
- Multimeter Profile
- Multimeter Appa
- Multimeter Amprobe
- Multimeter Tacklife
- Multimeter Somogyi
- Multimeter Steren
- Multimeter Flir
- Multimeter Maxwell
- Multimeter Topcraft
- Multimeter Altai
- Multimeter Plieger
- Multimeter Greenlee
- Multimeter Högert
- Multimeter Wago
- Multimeter Bruder Mannesmann
- Multimeter Metrel
- Multimeter Digi-tool
- Multimeter Elma
- Multimeter PCE Instruments
- Multimeter CEM
Najnowsze instrukcje dla Multimeter
19 Września 2024
18 Września 2024
18 Września 2024
17 Września 2024
17 Września 2024
17 Września 2024
17 Września 2024
17 Września 2024
17 Września 2024
16 Września 2024