Instrukcja obsługi Dual MMC36BT

Dual radio MMC36BT

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Dual MMC36BT (21 stron) w kategorii radio. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/21
INSTALLATION/OWNER'S MANUAL
Marine Receiver with Speaker Zone Control
MMC36BT
Inputs
Weather
Band
Tunner
2
MMC36BT
Please read entire manual before installation.
Installation
Mounting the Controller
1. Choose a mounting location the dash board or instrument panel that will in
allow room behind to run cables to the . Consider how you the black box
will use the AUX IN, LINE and USB and route the appropriate OUTPUTS connector
extension cables to an accessible area a RCAnd for installation.
3. Once you have determined a mounting location, you will need to cut a rectangular
shaped hole in the panel (4.84” X 3.15” / 123mm X 80mm).
IMPORTANT! Do not mount the commander or black box where they are submerged in water.
4. After the hole is cut slide the commander and wiring into the hole.
5. Slide the included spring washers (B) over the screw posts (A) and attach the screw
posts to the back of the commander.
6. Place the “U” bracket (C) over the screw posts and secure the radio to the dash using the
included hex nuts (D). If necessary, cut the score marks (E) on either side of the mounting
bracket to custom fit the bracket length for your application.
NOTE: Before final installation, test the wiring connections to make sure the unit
is connected properly and the system works.
7. When the black box installation, use the 4 rubber mounting stoppers (included in package)
on the bottom of the black box. This provides clearance from surface moisture and provides
sufficient ventilation for the heat.
9. Plug in all wiring harnesses and cables.
C
D
E
A
B
BLACK BOX
RUBBE E EA)R ST OPP R (4
C OLLERONTR Cutout dimensions
123 X 84mmmm
2. The contorller should be mounted to a dry, clean and flat surface.
8. Connect the controller to the black box using the supplied 13-pin DIN cable.
3
MMC36BT
Wire Connection
Fuse:
When replacing the fuse, make
sure new fuse is the correct type
and amperage. Using an incorrect
fuse could damage the radio.
Tip:
When a suitable ground wire is
not present in the vehicle wiring
harness, connect the black ground
wire to the vehicle chassis.
ACC (+12V)
GROUND (-)
CAMERA (+)
AMP T URN- (+)ON
REVE E (+)RS
(Brown)
(Gray)
(Black)
(Yellow)
(Blue)
(Blue)
(White)
(Red)
( ite)Wh
(Red)
( ite)Wh
(Red)
FRONT
CHANNEL AUXSUBWOOFER REAR
CHANNEL
FUSE
(Red)
(Black)
(Brown)
(Blue)
(Orange)
(Yellow)
LINE OUT
LEFT
LIN OUTE
RIGHT
LIN OUTE
LEFT
LIN OUTE
RIGHT
AUX IN
LEFT
AUX I N
RIGHT
Zone 1
SPEAKERS
Zone 2
SPEAKERS
Zone 3
SPEAKERS
(White)
(White/Black)
FRONT LEFT
FRONT RIGHT
REAR LEFT
REAR RIGHT
(Gray)
(Gray/Black)
(Green)
(Green/Black)
(Violet)
(Violet/Black)
(White)
(Whit Blac k)e/
(Gray)
(Gray/Bl ack)
(Green)
(Green/Black)
(Violet)
(Violet/Black)
DISPLAY
CONTROLLER
MaleFemale
13-pin Din Cable
3m (10 feet)
SWI INPUT USB CAMERA INPUT
ANTENNA
(Black)
(Black)
LEFT
RIGHT
LEFT
RIGHT
(Black)
(Optional R17) MW
DISPLAY
CONTROLLER
20A
ZONE 1
ZONE 2 & 3


Specyfikacje produktu

Marka: Dual
Kategoria: radio
Model: MMC36BT

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Dual MMC36BT, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje radio Dual

Dual

Dual DAB 420 BT Instrukcja

4 Października 2024
Dual

Dual DAB 71 Instrukcja

26 Września 2024
Dual

Dual DAB 100 Instrukcja

25 Września 2024
Dual

Dual DAB 27 Instrukcja

25 Września 2024
Dual

Dual DAB 4C Instrukcja

24 Września 2024
Dual

Dual DAB 500 Instrukcja

24 Września 2024
Dual

Dual DAB 400 Instrukcja

24 Września 2024
Dual

Dual BR - 2 Instrukcja

23 Września 2024
Dual

Dual DAB 81 Instrukcja

23 Września 2024
Dual

Dual BR Instrukcja

23 Września 2024

Instrukcje radio

Najnowsze instrukcje dla radio