Instrukcja obsługi Dimplex Mansfield MAN20CH
Dimplex
Otwarte palenisko
Mansfield MAN20CH
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Dimplex Mansfield MAN20CH (7 stron) w kategorii Otwarte palenisko. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/7
MANSFIELD INSET
MAN20BR & MAN20CH
The product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic Compatibility (EMC)
EN55014, These cover the essential requirements of EEC Directives 2006/95/EC and 2004/108/EC
08/52561/0 Issue 0
Dimplex MANSFIELD Inset Fires
Model: MAN20BR, MAN20CH
IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR
FUTURE REFERENCE
Important Safety Advice:
When using electrical appliances, basic precautions should always be followed to
reduce the risk of re, electrical shock and injury to persons, including the following:
If the appliance is damaged, check with the supplier before installation and operation.
Do not use outdoors.
Do not use in the immediate surroundings of a bath, shower or swimming pool.
Do not locate the heater immediately below a xed socket outlet or connection box.
This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved. Children shall not play
with the appliance. Cleaning and user mantenance shall not be made by children with
out supervision.
Children of less than 3 years should be kept away unless continuously supervised.
Children aged from 3 years and less thab 8 years shall only switch on/off the
appliance provided that it has been placed or installed in its intended normal
operating position and they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the hazards involved. Children
aged from 3 years and less than 8 years shall not plug in, regulate and clean the
appliance or perform user mantenance.
CAUTION
Some parts of this product can become very hot and cause burns. Particular attention
has to be given where children and vulnerable people are present.
Do not use this heater in series with a thermal control, a program controller, a timer or
any other device that switches on the heat automatically, since a re risk exists when
the heater is accidentally covered or displaced.
Ensure that furniture, curtains or other combustible material are positioned no closer
than 1 metre from the heater.
In the event of a fault unplug the heater.
Unplug the heater when not required for long periods.
Although this heater complies with safety standards, we do not recommend its use on
deep pile carpets or on long hair type of rugs.
The appliance must be positioned so that the plug is accessible.
If the supply cord is damaged it must be replaced by the manufacturer or service
agent or a similarly qualied person in order to avoid a hazard.
Keep the supply cord away from the front of the heater.
WARNING: In order to avoid overheating, do not cover the heater. Do not place
material or garments on the heater, or obstruct the air circulation around the heater.
The heater carries a DO NOT COVER warning.
Control Knob ‘C’:- Controls the Thermostat setting.
Turning the control knob Anti Clockwise will decrease the temperature setting, turning the control knob Clockwise
will increase the temperature setting.
Control Knob ‘D’:- Controls the intensity of the ame eect.
Turning the control knob Anti Clockwise increases the ame eect, turning the control knob Clockwise will decrease
the ame eect.
When the water in the tank and in the sump runs out the main lamps will go out. See instructions under ‘Maintenance’, ‘Filling
the water tank’. When this procedure is complete, the main lamps will illuminate but it will take 30 seconds before the ames
return.
Setting the Thermostat
Plug in and switch on the re to the full heat setting. Turn the Control Knob ‘C’ fully clockwise (max temperature setting) to
warm the room rapidly. When the room temperature has reached the desired level, turn the thermostat knob back slowly until
you hear the thermostat just click o. The heater will then maintain the room temperature at the chosen level.
Note: Should your heater fail to come on when the thermostat is at a low setting, this may be due to the room temperature
being higher then the thermostat setting
Thermal safety cut-out
A thermal safety cut-out is incorporated in the fan heater to prevent damage due to overheating. This can happen if the heat
outlet was restricted in any way or if the chimney ue has not been blocked o eectively. If the cut-out operates, unplug the
heater from the socket outlet and allow approximately 10 minutes before reconnecting. Before switching the heater back on
remove any obstruction that may be restricting the heat outlet, then continue normal operation.
Caution: In order to avoid a hazard due to inadvertent resetting of the thermal cutout, this appliance must not be supplied
through an external switching device, such as a timer, or connected to a switch that is regularly switched on and o by the
utility.
Tips for using your appliance.
1. With the ame setting on minimum the unit will use approximately 40ml of water per hour and will last 3 times as long than
when it is at maximum ame setting.
2. Do not tilt or move the re while there is water in the tank or sump.
3. Make sure that the re is on a level oor.
4. The ame control knob ‘D’ Fig.2 may be turned up or down to give a more realistic eect.
5. Sometimes the ames appear more real when the ame control knob is turned down.
6. Give the ame generator some time to react to changes you may make on the ame control knob.
Maintenance
WARNING: ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE BEGINNING ANY MAINTENANCE
Changing lamps.
If the smoke appears grey or colourless it may be that one or more lamps have failed.
You can check for lamp failure as follows.
1. Leaving the ame eect on, lift out the fuelbed and water tank. (See Fig.3)
2. It should be possible to view the lamps with the nozzle (See Fig.4) in place and observe which one needs to be changed.
3. Put Switch ‘A’ in the ‘OFF’ position, and unplug the re from the mains.
4. Leave the appliance for 20 minutes to allow the lamps to cool down before removing them.
5. Remove the sump as described in the Cleaning Section.
6. Remove the defective lamp, by gently lifting vertically and disengaging the pins from the lamp holder, (See Fig.4 and 4a).
Replace with a Dimplex OPTIMYST, 12V, 50W, Gu5.3 base, 8º beam angle, coloured lamp. (Purchased from www.dimplex.co.uk
under the section ‘After Sales Service’, details of how to purchase the lamps are contained therein.)
7. Carefully insert the two pins of the new lamp into the two holes in the lamp holder. Push rmly in place. (See Fig.4 and 4a).
8. Replace the sump, nozzle, water tank and fuelbed.
9. Switch on.
Filling the water tank.
When the water tank is empty, the ame and smoke eect shuts o and you will hear 2 audible beeps, follow these steps.
1. Press Switch ‘A’ to (See Fig.2)(0)
2. Gently lift out the fuelbed and set aside carefully. (See Fig.3)
3. Remove the water tank by lifting upwards and outwards.
4. Place the water tank in sink and remove cap, Anti-clockwise to open. (See Fig.5)
5. Fill tank with ltered tap water only . This is necessary to prolong the life of the ame and smoke producing unit.
The water should be ltered through a conventional domestic water lter unit and the lter should be replaced regularly.
6. Screw the cap back on, do not overtighten.
7. Return the tank to the sump, with the tank cap facing down and the at side of the tank facing outward.
Specyfikacje produktu
| Marka: | Dimplex |
| Kategoria: | Otwarte palenisko |
| Model: | Mansfield MAN20CH |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Dimplex Mansfield MAN20CH, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Otwarte palenisko Dimplex
26 Września 2024
26 Września 2024
26 Września 2024
23 Września 2024
21 Września 2024
21 Września 2024
21 Września 2024
21 Września 2024
20 Września 2024
7 Września 2024
Instrukcje Otwarte palenisko
- Otwarte palenisko Smeg
- Otwarte palenisko Ardes
- Otwarte palenisko Ambiano
- Otwarte palenisko Einhell
- Otwarte palenisko Bimar
- Otwarte palenisko Furrion
- Otwarte palenisko Bomann
- Otwarte palenisko Klarstein
- Otwarte palenisko Qlima
- Otwarte palenisko TriStar
- Otwarte palenisko Invicta
- Otwarte palenisko Napoleon
- Otwarte palenisko Blumfeldt
- Otwarte palenisko Fieldmann
- Otwarte palenisko Edilkamin
- Otwarte palenisko Cotech
- Otwarte palenisko Eurom
- Otwarte palenisko EWT
- Otwarte palenisko Well Straler
- Otwarte palenisko Faber
- Otwarte palenisko Manor House
- Otwarte palenisko Brixton
- Otwarte palenisko La Nordica
- Otwarte palenisko Jotul
- Otwarte palenisko Hwam
- Otwarte palenisko Euromac
- Otwarte palenisko Deville
- Otwarte palenisko Spartherm
- Otwarte palenisko Haas+Sohn
- Otwarte palenisko Olsberg
- Otwarte palenisko Firefriend
- Otwarte palenisko Uniflame
- Otwarte palenisko Eligent
- Otwarte palenisko Blue Rhino
- Otwarte palenisko Amantii
- Otwarte palenisko Planika
Najnowsze instrukcje dla Otwarte palenisko
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024