Instrukcja obsługi DeWalt DW746X

DeWalt Maszyna do piłowania DW746X

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla DeWalt DW746X (52 stron) w kategorii Maszyna do piłowania. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/52

INSTRUCTION MANUAL

GUIDE D'UTILISATION

MANUAL DE INSTRUCCIONES

DW746, DW746X

Woodworker’s Table Saw

Scies circulaires à table d’entrepreneur

Sierra de banco para madera

INSTRUCTIVO DE OPERACIÓN, CENTROS DE

SERVICIO Y PÓLIZA DE GARANTIA. ADVERTENCIA:

LEASE ESTE INSTRUCTIVO ANTES DE USAR EL

PRODUCTO. SI TIENE DUDAS, POR FAVOR LLAME.

Before returning this

product call

1-800-4-DEWALT

IF YOU SHOULD EXPERIENCE A PROBLEM WITH

YOUR D EWALT PURCHASE,

CALL 1-800-4 DEWALT

IN MOST CASES, A DEWALT REPRESENTATIVE CAN RESOLVE YOUR

PROBLEM OVER THE PHONE.

IF YOU HAVE A SUGGESTION OR COMMENT, GIVE US A CALL.

YOUR FEEDBACK IS VITAL TO THE SUCCESS OF DEWALT'S QUALITY

IMPROVEMENT PROGRAM.

See our catalog on the World Wide Web at www.dewalt.com

English

GROUNDED, CORD-CONNECTED MACHINES INTENDED FOR USE ON A SUPPLY

CIRCUIT HAVING A NOMINAL RATING LESS THAN 150 VOLTS

If the machine is intended for use on a circuit that has an outlet that looks like the one

illustrated in Fig. A, the machine will have a grounding plug that looks like the plug illus-

trated in Fig. A. A temporary adapter, which looks like the adapter illustrated in Fig. B,

may be used to connect this plug to a matching two-conductor receptacle as shown in

Fig. B if a properly grounded outlet is not available. The temporary adapter should be

used only until a properly grounded outlet can be installed by a qualified electrician. The

green-colored rigid ear, lug, and the like, extending from the adapter must be connected

to a permanent ground such as a properly grounded outlet box. Whenever the adapter

is used, it must be held in place with a metal screw.

GROUNDED

OUTLET

BOX

GROUNDING PIN

GROUNDING

MEANS

ADAPTER

GROUNDING PIN

A B C D

NOTE: In Canada, the use of a temporary adapter is not permitted by the Canadian

Electric Code.

DANGER: IN ALL CASES, MAKE CERTAIN THAT THE RECEPTACLE IN QUESTION IS

PROPERLY GROUNDED. IF YOU ARE NOT SURE, HAVE A QUALIFIED ELECTRICIAN

CHECK THE RECEPTACLE.

240 Volt, Single-Phase Operation

The motor supplied with your machine is a dual voltage, 120/240 volt motor. It is shipped

ready-to-run for 120 volt operation. However, it can be converted for 240 volt operation. A

qualified electrician should perform the conversion or take the machine to an authorized

DEWALT service center. When conversion is complete, the machine must conform to the

National Electric Code and all local codes and ordinances.

The machine is converted by rewiring the motor for 240 volts, installing a

240-volt plug on the power supply cord and replacing the switch (if neces-

sary) with one that is rated for 240-volt operation.

The saw with the 240-volt plug should ONLY be connected to an outlet

having the same configuration as the plug illustrated. No adapter is avail-

able or should be used with the 240-volt plug.

DANGER: IN ALL CASES, MAKE CERTAIN THAT THE RECEPTACLE

IN QUESTION IS PROPERLY GROUNDED. IF YOU ARE NOT SURE, HAVE A QUALIFIED

ELECTRICIAN CHECK THE RECEPTACLE.

Double Insulation

If saw is of double-insulated construction, read the following instructions.

Double insulated tools are constructed throughout with two separate layers of electrical

insulation or one double thickness of insulation between you and the tool’s electrical system.

Tools built with this insulation system are not intended to be grounded. As a result, your tool

is equipped with a two prong plug which permits you to use extension cords without concern

for maintaining a ground connection.

NOTE: Double insulation does not take the place of normal safety precautions when oper-

ating this tool. The insulation system is for added protection against injury resulting from a

possible electrical insulation failure within the tool.

Definitions: Safety Guidelines

The definitions below describe the level of severity for each signal word. Please read

the manual and pay attention to these symbols.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may

result in minor or moderate injury.

CAUTION: Used without the safety alert symbol indicates a potentially hazardous

situation which, if not avoided, result in may property damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT

TOOL, CALL US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258)

General Safety Rules

WARNING: Read all instructions before operating product. Failure to follow all

instructions listed below may result in electric shock, fire and/or serious injury.

SAVE THESE INSTRUCTIONS

WARNING: FOLLOW ALL WIRING CODES and recommended electrical connections to

prevent shock or electrocution.

Grounding Instructions

If saw is of grounded construction, read the following instructions.

DANGER: SHOCK HAZARD. THIS MACHINE MUST BE GROUNDED WHILE IN USE.

SERIOUS INJURY COULD RESULT.

ALL GROUNDED, CORD-CONNECTED MACHINES

In the event of a malfunction or breakdown, grounding provides a path of least resis-

tance for electric current to reduce the risk of electric shock. This machine is equipped

with an electric cord having an equipment-grounding conductor and a grounding plug.

The plug must be plugged into a matching outlet that is properly installed and grounded

in accordance with all local codes and ordinances. Do not modify the plug provided - if it

will not fit the outlet, have the proper outlet installed by a qualified electrician. Improper

connection of the equipment-grounding conductor can result in risk of electric shock.

The conductor with insulation having an outer surface that is green with or without yel-

low stripes is the equipment-grounding conductor. If repair or replacement of the electric

cord or plug is necessary, do not connect the equipment-grounding conductor to a live

terminal. Check with a qualified electrician or service personnel if the grounding instruc-

tions are not completely understood, or if in doubt as to whether the machine is properly

grounded. Use only three-wire extension cords that have three-prong grounding type

plugs and matching three-conductor receptacles that accept the machine’s plug, as

shown in Fig. A. Repair or replace damaged or worn cord immediately.

Specyfikacje produktu

Marka:	DeWalt
Kategoria:	Maszyna do piłowania
Model:	DW746X

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z DeWalt DW746X, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Maszyna do piłowania DeWalt

DeWalt DCCS621 Instrukcja

3 Stycznia 2025

DeWalt DCPS671 Instrukcja

3 Stycznia 2025

DeWalt DCS590 Instrukcja

3 Stycznia 2025

DeWalt DW861 Instrukcja

9 Października 2024

DeWalt DCS397 Instrukcja

7 Października 2024

DeWalt DWE249 Instrukcja

7 Października 2024

DeWalt DWM120 Instrukcja

2 Października 2024

DeWalt DW309K Instrukcja

30 Września 2024

DeWalt DW317 Instrukcja

30 Września 2024

DeWalt DW100 Instrukcja

23 Września 2024

Instrukcje Maszyna do piłowania

Najnowsze instrukcje dla Maszyna do piłowania

Husqvarna 455e Rancher Instrukcja

12 Stycznia 2025

Güde GSS 400 Instrukcja

12 Stycznia 2025

Makita DUC306PG2 Instrukcja

12 Stycznia 2025

HiKOKI C 6BU3 Instrukcja

11 Stycznia 2025

DEDRA DED7060 Instrukcja

11 Stycznia 2025

Einhell KGS 190 Instrukcja

11 Stycznia 2025

Sun Joe SWJ599E Instrukcja

11 Stycznia 2025

Einhell BT-MB 550 U Instrukcja

11 Stycznia 2025

Maruyama MCV51 Instrukcja

11 Stycznia 2025

Vonroc JS505DC Instrukcja

9 Stycznia 2025